간행물
한국기계기술학회지 KCI 등재 Journal of the Korean Society of Mechanical Technology 韓國機械技術學會誌
- 발행기관 한국기계기술학회
- 자료유형 학술지
- 간기 격월간
- ISSN 1229-604X (Print)2092-0385 (Online)
- 수록기간 1999 ~ 2024
- 주제분류 공학 > 기계공학 공학 분류의 다른 간행물
- 십진분류KDC 550DDC 620
권호리스트/논문검색
제17권 제2호 (2015년 4월) 35건
21.
2015.04
구독 인증기관 무료, 개인회원 유료
The performance of helical hydro turbine in water pipe line depends on the sectional shape of turbine blade, pitch angle of turbine blade, solidity and number of turbine blades, To investigate the effects of these design factors on the performance of helical hydro turbine, flow analysis was carried out by using commercial code ANSYS CFX version 14..5. From CFD analysis we obtained the optimum design factors which were the asymmetric blade shape of NACA4420, the pitch angle of 15 degrees and the solidity of 0.3. These results can be used for the actual design of sphere-shaped helical turbine in water pipe line.
4,000원
22.
2015.04
구독 인증기관 무료, 개인회원 유료
Dental brackets are widely used by the orthodontists to correct the misalignment of teeth in the mouth over a long period of time. In this study, finite element analysis of orthodontic bracket has been carried out for the observation of the stress distribution and deformation pattern in the different materials bracket (Stainless Steel, Ceramic, Titanium, Polycarbonate and Nitinol) when subjected to arch wire torsion and tipping force. The simulation results were further optimized with respect to bracket attachment surface. It was found that it is possible to know the change in result is correlated with the attachment surface of the stress and deformation due to change in diameter. The results confirmed that the finite element method has proved to be successful for proper design analysis for future development of the teeth bracket.
4,000원
23.
2015.04
구독 인증기관 무료, 개인회원 유료
A three-dimensional computational fluid dynamics code is developed for predicting nonequilibrium flowfields over Mars entry probes. The numerical scheme is based on the cell-vertex finite volume method for a prismatic unstructured mesh system. Internal energy excitations and chemical reactions with finite rates are considered by introducing the two-temperature model of Park. Eight chemical species, C, N, O, CO, N2, NO, O2, and CO2, and nine chemical reactions are considered in the calculations. The developed code is verified in terms of prediction of heat flux to the body surface near the stagnation point of a Mars entry probe flying with the velocity of 6 km/s. The calculated heat flux reasonably agree with the calculated result in the past studies.
4,000원
24.
2015.04
구독 인증기관 무료, 개인회원 유료
The regular safety inspection of vehicles in service has been tested up to now not by a plate type (dynamic) inspection system but by a roller type (static) inspection system in our country (in Korea). Therefore, the roller type inspection can not reflect the inertia force that there is a load transfer from the rear axle to the front axle during braking. In this study, before introducing the plate type inspection system, the effect on braking force characteristics according to entering velocities of vehicles in service are evaluated statistically. As the results, the reliable entering velocity range is about from 7 km/h to 14 km/h. Also, the regular vehicle safety inspection in domestic country need to adopt the plate type (dynamic) braking force inspection system which can reflect the inertia force.
4,000원
25.
2015.04
구독 인증기관 무료, 개인회원 유료
The objective of this study is to predict the formability of sheet metal for the bladder press. The static implicit finite element method is applied effectively to analyze bladder forming processes using AutoForm software. The material used for forming analysis is AL2024, and the thickness of the plate is 1.6mm, 1.8mm and 2.0mm. Forming force is shown by 101.92kN～87.22kN. The result from the simulation analysis was applied to the bladder press system.
4,000원
26.
2015.04
구독 인증기관 무료, 개인회원 유료
In this paper, the design of hydraulic system for leveling control of a large vehicle was developed. The hydraulic system for leveling control was consisted of four hydraulic actuators and two gravity referenced inclinometer. In order to verify the effectiveness of leveling system via simulation, Hydraulic actuators, vehicle and control algorithm were modeled using ADAMS which is a commercial dynamic analysis software for multi-body system. The test and simulation results of hydraulic actuator were compared and it showed the properness of simulation model. The effectiveness of hydraulic system and leveling control algorithm were verified via simulation results.
4,000원
27.
2015.04
구독 인증기관 무료, 개인회원 유료
The hydraulic equipments has a high utilization in the many works such as the excavation, planation and crane works in the construction sites. They are an essential equipments in the construction site and the loading & unloading works of the large size objects.
In the many parts which are composed of the hydraulic equipments, the main control valve(MCV) is the core of the equipments. The hydraulic energy from the pump controls the direction and the rate of flow by MCV. And the flow rate of the MCV inlet operate some actuators to perform the diverse action of the spool. So, it is important to analysis the shape of the flow path and the notch of the spool. In order to perform the optimal design of the 6-way valve, the study for the analysis of the flow path and the pressure distribution according to the pressure control, which to meet use condition, must be performed.
In this study, we carried out the reverse-engineering of the MCV using the parametric technique as the first step in the research of the MCV. And we analyzed the shape of the flow path and the pressure distribution for the notch of the spool using the optimal modeling of the MCV.
4,000원
28.
2015.04
구독 인증기관 무료, 개인회원 유료
The expansion of the display market could mass-produce the product which becomes the super-slim and ultra-lighting according to the demand of customer. This change etched the mobile display panel in order to make the thin glass. The wet etching refers to the process of removing selectively the unnecessary part in order to form the circuit pattern among the semi-conductor or the LCD manufacturing process. The wet etching can progress the etching about a large amount at a time but the thickness of glass is not smooth or not etched according to the process condition. In this study, the defect factor in the etching process tries to be analyze. The experimental design was established and the processing condition was optimized in order to minimize under non-etch part generation by the experiment of design.
4,000원
29.
2015.04
구독 인증기관 무료, 개인회원 유료
In this study, development of the manufacturing system for the oriental medicine needle was carried through the wire drawing from the wire supply, straightness, heat treatment and surface treatment processes, and finally wire cutting or winding by the online process. As a result, a prototype manufacturing system for the oriental medicine needle wire has been developed. It has been shown that all development targets, such as, straightness, precision, surface roughness, tensile strength, discoloration, noise, diameter range and maximum production speed have been satisfied through the performance test.
4,000원
30.
2015.04
구독 인증기관 무료, 개인회원 유료
In this paper, the design of hydraulic actuating circuit of doing over-running load was performed. Generally, the counter balance valve has been used to protect over-run or free falling of acuating system. But sometimes, it makes some undesirable problems such as pressure surge or vibration. To overcome such problems and satisfy the system requirements, we suggest the hydraulic circuit actuated by servo valve. In order to verify the properness of suggested hydraulic circuit, hydraulic actuator with servo valve was modeled using ADAMS/Hydraulic which is a commercial dynamic analysis software for multi-body system. Also, the effectiveness of hydraulic actuating circuit was verified via test bed and real plant.
4,000원
31.
2015.04
구독 인증기관 무료, 개인회원 유료
The purpose of this study is to introduce the Inventogram program and create new ideas and looking to take advantage of this product. So all this research is that it can be an easy invention. In this study, we'll demonstrate the idea of creating a derivation of the coffee roaster grinder to crush the coffee green bean utilize Inventogram program to prove it.
4,000원
32.
2015.04
구독 인증기관 무료, 개인회원 유료
In this paper, research development about a bladder press forming system has been carried out for sheet metal forming. The bladder press forming system consists largely of three units as follows forming process unit, driving unit and hydraulic power unit including bladder. Structural analysis of frame of total system by the ANSYS program, flow analysis of bladder by CFX version 14 and hydraulic circuit analysis by AMESim were carried for basic design of bladder press forming system. We can get a good forming results from bladder press system. Developed bladder press forming system will be largely used in aircraft manufacturing industry field.
4,000원
33.
2015.04
구독 인증기관 무료, 개인회원 유료
In this study, the effect of upper die type on the load characteristics of lower die and the wasted material was studied numerically. The different shapes(A-type, B-type, and C-type) of upper die were applied. Also finite element analysis method was applied for the analysis in each stage. The half of X, Y plane was analyzed due to the symmetrical shape in order to reduce the analysis time and be accurate results. The coefficient of friction was set to oil_cold conditions as refer to the system library.
It was revealed that principal stress was the order in A, C, and B. A and B type have the highest value in 4 stage, and C type shows the highest value in 3 stage. In addition, Von mises stress were higher in order A, B, and C. A and B type have the highest in 4 stage, and C type shows to have about the same value in the 2 - 5 stage. The load was generally higher than C type. The load of C type was reduced in YY-direction at each stage without 2, 5, 6 stage.
3,000원
34.
2015.04
구독 인증기관 무료, 개인회원 유료
In this study, we have developed an automatic manufacturing system for functional wood plastic composites(WPC) which are one of spotlighting materials for landscape architecture and residential construction material. In addition to the existing facilities, this manufacturing system is consist of an automatic hole manufacturing device, iron band supply and winding device, mold with the iron band insert system, calibration unit, control system, etc. We have performed the performance tests for the system such as the specific gravity, bending strength, screw holding power, percentage of moisture content, formaldehyde, absorption thickness, expansion rate, cold resistance(appearance & bending strength), and shock resistance. As a result, the performance of the prototype system satisfies all the objects of this study.
4,000원
35.
2015.04
구독 인증기관 무료, 개인회원 유료
In this paper, we developed the hydraulic leveling jack(HLJ) with double-tube type structure which could be applicable to excessive lateral load area. In order to develop HLJ, the design requirements, such as the vertical and lateral loads where applied to hydraulic jack, were selected. To verify the structural stability of the HLJ, the structure analysis was performed. In order to verify the operational performance and structural stability of the developed HLJ, test bench was designed. The performance of HLJ was verified via various test using test bench.
4,000원
1
2
