본 논문에서는 유한요소해석을 통한 모듈러 구조물 접합부의 힌지접합부 연구에 관하여 소개한다. 모듈러 구조물은 모듈과 모듈을 적층하는 방식으로 공사를 진행하여 단위 모듈간의 기둥 및 보의 일체성을 기대하기 어려운 특성을 가지고 있다. 그러나 현 모듈러 설 계 시 이러한 구조적 특성을 무시하고 횡력에 대한 모멘트전달을 고려하여 기존 강구조와 동일한 방식으로 해석하고 있다. 더구나 모 멘트접합을 체결하기위해 모듈러 외부뿐만 아니라 내부에서 볼트 체결이 이루어져 조립 후 마감을 추가하는 불합리한 상황도 발생한 다. 이러한 일체성을 기대하기 어려운 특성을 고려하기 위하여 힌지접합을 활용한 모듈러구조시스템을 제안하였다. 논문에서는 기존 의 모멘트접합부에서 힌지접합부로 변경하였을 때 하중의 전달을 확인하기 위하여 이전 다른 연구에서 활용되었던 가위 모델을 변형 한 변형 가위 모델을 고안하여 접합부의 기본 이론을 제안·검토하였고, 기본을 바탕으로 계산된 결과는 구조해석 프로그램인 마이다 스 젠과 비교하여 검증하였다. 추가적으로 기존 모멘트접합부로 설계되었던 모듈러구조물을 힌지접합부로 변경하여 부재내력 및 사 용성을 검토하였다.

This paper presents the effect on the inelastic behavior and structural performance of concrete and filled steel pipe through a numerical method for reliable judgment under various load conditions of the CJS composite structural system. Variable values optimized for the CJS synthetic structural system and the effects of multiple variables used for finite element analysis to present analytical modeling were compared and analyzed with experimental results. The Winfrith concrete model was used as a concrete material model that describes the confinement effect well, and the concrete structure was modeled with solid elements. Through geometric analysis of shell and solid elements, rectangular steel pipe columns and steel elements were modeled as shell elements. In addition, the slip behavior of the joint between the concrete column and the rectangular steel pipe was described using the Surface-to-Surface function. After finite element analysis modeling, simulation was performed for cyclic loading after assuming that the lower part of the foundation was a pin in the same way as in the experiment. The analysis model was verified by comparing the calculated analysis results with the experimental results, focusing on initial stiffness, maximum strength, and energy dissipation capability.

This study proposed a simplified finite element analysis procedure for designing the nonstructural masonry wall in the out-of-plane direction. The proposed method is a two-step elastic analysis procedure by bilinearizing the behavior of the masonry wall. The first step analysis was conducted with initial stiffness representing the behavior up to the effective-yield point, and the second step analysis was conducted with post-yield stiffness. In addition, the orthotropic material property of the masonry was considered in the FE analysis. The maximum load was estimated as the sum of the maximum loads in the first and second step analyses. The maximum load was converted into the moment coefficients and compared with those from the yield line method applied in Eurocode 6. The moment coefficients calculated through the proposed procedure showed a good match with those from the yield line method with less than 6% differences.

Gas springs applied to various industrial fields are generally composed of a cylinder, a piston rod, a cover, and a seal mount. Because of the thin wall of the cylinder, small gas springs are manufactured using a roller forming process that presses the cylinder wall into a groove of cover in the cylinder. In this study, finite element analysis and process design of roller forming are performed to systematically manufacture the small gas spring and develop a roller forming machine. In order to perform roller forming analysis, tensile tests of structural steel pipe are performed and mechanical properties are analyzed. Roller forming process parameters such as radius and depth of roller grooves are derived using the incompressible condition of plastic deformation theory and the results of finite element roller forming analysis. Using the derived roller shape, a roller forming machine is developed and prototypes of the small gas spring are manufactured. Finally, the dimensional accuracy of the manufactured gas spring prototypes is analyzed through three-dimensional shape measurement.

본 논문에서는 우리나라의 중저준위 방폐물 처분을 위한 사일로 형식 지하동굴의 유한요소해석을 수행하였다. 사일로의 벽체부분 은 지름 25m의 원형구조이고, 높이는 35m이다. 사일로의 천장부분은 지름 30m의 돔 형식이고, 높이 17.4m의 규모이다. 사일로는 해 수면으로부터 –80m에서 –130m에 위치하고 있다. 중저준위 방폐물 처분 1단계 시설로 6개의 사일로가 건설되어 운영되고 있으나, 본 연구에서는 1개의 사일로에 대해서 고려하였다. SMAP-3D 프로그램을 사용하여 2차원 축대칭 유한요소모델과 3차원 유한요소모델 을 생성하였다. Generalized Hoek and Brown Model이 수치해석에 적용되었다. 다양한 측압계수(수평방향 현장응력과 수직방향 현장 응력의 비)의 변화에 따른 사일로 형식 지하동굴의 유한요소해석을 수행하였으며, 수치해석결과 및 분석결과가 제시되었다.

Due to environmental pollution, regulations on existing petroleum-based fuels are increasing day by day. LNG is in the spotlight as an eco-friendly fuel that does not emit NOx or SOx, but its boiling point is -163°C, so it needs to be handled with care. Materials that can be used at the above temperature are defined by IMO through the IGC Code. Among them, 9% nickel steel has great advantages in yield strength and tensile strength under cryogenic conditions, but it is difficult to use in arc welding such as FCAW for various reasons. This study is a study to apply fiber laser welding to solve this problem. As a previous study, this study conducted a study to find a welding heat source. After performing bead on plate welding, the optimal heat source was derived by analyzing the shape of the bead and adjusting the parameters of the heat source model. In this case, by applying the multi-island genetic algorithm, which is a global optimization algorithm, not the intuition of the researcher, accurate results could be derived in a wide range.

ROPS is a structure installed to protect drivers from tractor rollover accidents and is being tested for certification under the OECD code. Because this test requires a lot of cost and time to develop the ROPS and to produce test model, the OECD is discussing the introduction of virtual test using finite element analysis. In this study, the results were compared by conducting a strength test and finite element analysis applied with the OECD code to use it as a basic data for standardization of ROPS virtual test methods. It was confirmed that the results of the analysis of the bolts and plates of the coupling part and the folding part were more close to the physical test results than the rigid elements and constraints at the point of coupling the tractor and ROPS.

In this paper, nonlinear finite element analysis was conducted based on the experimental results on buckling restrained brace. The reliability of the analytical model was verified by comparing the results of experimental studies with hysteresis loop, bi-linear curve, cumulative energy dissipation capacity, and equivalent viscous damping. A valid finite element model has been secured and will be used as basic data for finite element analysis of buckling restrained braces in the future.

This study develops finite element models for seismically-deficient reinforced concrete building frame retrofitted using fiber-reinforced polymer jacketing system and validates the finite element models with full-scale dynamic test for as-built and retrofitted conditions. The bond-slip effects measured from a past experimental study were modeled using one-dimensional slide line model, and the bond-slip models were implemented to the finite element models. The finite element model can predict story displacement and inter-story drift ratio with slight simulation variation compared to the measured responses from the full-scale dynamic tests.

In this study, the seismic safety of nuclear power plant structures is evaluated and verified by performing a vibration test on a relatively simple shear wall structure. The shear walls are the prominent members of nuclear power plants and resist the seismic load. The shear wall structure is designed and manufactured to perform shaking table tests and is used to increase the accuracy of the analytical method by comparing them with the numerical analysis results. Different results will be checked and more efficient application methods will be studied depending on the method of designing reinforced concrete structures.

본 논문에서는 Needle-punched C/SiC 복합재료 해석을 위한 효율적인 멀티스케일 해석기법을 소개한다. 기존 Needle-punching으 로 인해 복잡한 미소구조를 갖는 NP 복합재료는 기존의 제안된 복합재료 멀티스케일 기법으로 물성을 계산하는 것은 한계가 있어 왔다. 이를 극복하기 위해 micro-CT 이미지 촬영을 통해 NP 복합재료의 미소구조를 면밀히 파악할 수 있었고, 이미지 프로세싱을 바탕으로 실제구조와 직접적으로 대응할 수 있는 3D high fidelity 모델을 구축하였다. 또한 유한요소해석에 맞춰 요소크기를 조절할 수 있는 sub-region processing 소개를 바탕으로 효율적인 유한요소해석을 수행하였다. NP 복합재료의 미소구조 거동뿐만 아니라, macro-scale 구조해석의 적용을 위해 subcell 모델링을 제안하였다. Needle-punching에 의한 Z축 NP 섬유의 규칙적인 간격을 이용하여 모델링을 수행할 수 있었다. 제안한 두 종류의 모델은 균질화 기법을 이용하여 등가거동 및 등가물성을 파악하였으며, 추가적인 실험 결과와의 비교를 통해 검증을 수행하였다.

이 논문에서는 공용중인 구조물의 상시 계측 자료를 사용한 온라인 유한요소 모델 업데이트 방법을 제안한다. 일반적인 최적화 방법에 기반한 기존의 방법은 최적해를 찾기까지 반복적으로 고유치 해석을 수행해야 하므로 상시 업데이트에 사용하기에는 효과적이지 못하다. 제안하는 방법은 별도의 오프라인 작업이나 사용자의 개입이 없이 자동화된 과정으로 계측과 동시에 온라인 유한요소모델 업데이트를 수행할 수 있는 새로운 방법이다. 자동화된 Cov-SSI 알고리즘을 통해 구조물의 진동 계측 신호로부터 고유진동수 및 모드 형상을 식별하고, 이를 다시 역 고유치 신경망에 입력하여 최종적으로 업데이트된 유한요소 모델의 파라미터를 추정한다. 풍하중을 받는 20층 전단 빌딩 구조 모형에 대한 수치예제를 통해 제시한 방법이 자동으로 연속적인 유한요소모델 업데이트를 할 수 있었음을 확인하였다. 또한, 계측 도중 구조물의 특성이 변화하는 시나리오에 대한 예제에서 구조물의 변화가 일어나는 시점과 변화 후 변동된 구조 모델 파라미터 값을 성공적으로 추정할 수 있음을 확인하였다.

Metal bodies have generally been produced through machining process, even the smallest parts that are assembled and mounted on the metal body. In this study, we will study the process of manufacturing parts called SIM Tray through compound forging process instead of cutting. The process of replacing a series of SIM Tray production process with a composite forging process by simulating the forming process using DEFORM-3D and making process design, mold design, mold fabricating.