검색결과

검색조건
좁혀보기
검색필터
결과 내 재검색

간행물

    분야

      발행연도

      -

        검색결과 44

        21.
        2017.11 KCI 등재 구독 인증기관 무료, 개인회원 유료
        In this paper, numerical modeling is conducted to analyze the tension of an anchor line by varying the size and drag coefficient of a buoy when the trapnet is influenced by the wave and the current simultaneously. A mass-spring model was used to analyze the behavior of trapnet underwater under the influence of waves and current. In the simulation of numerical model, wave height of 3, 4, 5 and 6 m, a period of 4.4 s, and the flow speed of 0.7 m/s were used for the wave and current condition. The drag coefficients of buoy were 0.8, 0.4 and 0.2, respectively. The size of buoy was 100, 50 and 25% based on the cylindrical buoy (0.0311 ㎥) used for swimming crab trap. The drag coefficient of the trapnet, the main model for numerical analysis, was obtained by a circular water channel experiment using a 6-component load cell. As a result of the simulation, the tension of the anchor line decreased proportional to buoy’s drag coefficient and size; the higher the wave height, the greater the decrease rate of the tension. When the buoy drag coefficient and size decreased to one fourth, the tension of the anchor line decreased to a half and the tension of the anchor line was lower than the holding power of the anchor even at 6 m of wave height. Therefore, reducing the buoy drag coefficient and size appropriately reduces the trapnet load from the wave, which also reduces the possibility of trapnet loss.
        4,000원
        22.
        2017.05 KCI 등재 구독 인증기관 무료, 개인회원 유료
        In this study, we propose a method of optimal placement technique of artificial reef considering characteristics of sea areas and provide basic data for efficient budget execution. In addition, we will contribute to increasing the economic efficiency by improving the fisheries productivity by suggesting the scientific basis for the policy data and the increase of the catch through the resource creation based on the ecological information about the biology. Especially, in order to establish the effective disposition (optimum separation distance) of artificial reef considering characteristics of biological and engineering factors, it is necessary to review the artificial reef installation management regulations and investigate the biological effects of artificial reef facilities, is needed. Through this, it is expected that the ground data of the direction of the policy promotion will be derived by suggesting the placement condition of the artificial reef complex which can maximize the resource composition effect according to the target fish species.
        4,000원
        25.
        2016.12 KCI 등재 구독 인증기관 무료, 개인회원 유료
        In this study, a new designed propeller was applied on 24 ton class squid jigging vessel to reduce of fuel consumption. The selected squid jigging boat was under construction at the shipyard to determine the resistance of the hull through the model experiment. The propeller design was carried out by using the experimental data and ITTC procedures. Sea trials were performed by measuring the speed and the horsepower required by the condition of five power levels of engine load, namely 70%, 80%, 90%, MCR and maximum engine power. The speed and delivered horse power were compared between the conventional propeller and the new design propeller. Delivered horse power by installing the new propeller takes 90% engine load at start-up conducted by decreased 9.06%. The measuring speed is increased up to the 0.6 knots in the low-speed range to high range. This study showed that only the design and installation of a new propeller can improve the propulsion efficiency of the boats; furthermore, reduce fuel costs can be achieved at the same time by improving the increased cruising speed.
        4,000원
        26.
        2016.12 KCI 등재 구독 인증기관 무료, 개인회원 유료
        This study aims to investigate effects of the length of the buoy and sand bag line on the loss of webfoot octopus pot. A numerical modeling and simulation was carried out to analyze the process that the pot gear affected by wave using the mass spring model. Through the simulation, tensions of sand bag line under various condition were investigated by length of buoy and sand bag line. The drag force and coefficient k of an artificial shell used in the webfoot octopus pot was obtained from an experiment in a circular water channel, and the coefficient k was applied to the simulation. To verify the accuracy of the simulation model, a simple test was conducted into measuring a rope tension of a hanging shell under flow. Then, the test result was compared with the simulation. The lengths of the buoy line in the simulation were 1.12, 1.41, 1.80, 2.23, 2.69, and 3.17 times of water depth. The lengths of sand bag line were 10, 20, 30, and 40 meters, and conditions of water depth were 8, 15, 22 meters. 4 meter height and 8 second period of wave were applied to all simulations. As a results, the tension of the sand bag line was decreased as the buoy and sand bag line were increased. The minimum tension of the sand bag line was appeared in conditions that the length of the buoy line is twice of water depth and the sand bag line length is over 40 meters (except in case of depth 8 meters.).
        4,000원
        27.
        2016.12 KCI 등재 구독 인증기관 무료, 개인회원 유료
        This study aims to reduce the force exerted to the buoy of the gillnet by wave and current. Five buoy models were selected for experiments and their rope tensions under wave and current action were compared. Five models were EL (ellipsoid), EL-H (ellipsoid-hole), SL (streamlined body), SP (sphere) and CL (cylinder, traditional type). In the first experiment, the Five models were tested without any attachment. In the second experiment, a flagpole was attached to each model. As a result, in the condition without flagpole, the tensions of four models with the exception of the CL were about a half of that of the CL. In the condition with flagpole, the tension of all models was twice larger than that without flagpole. Thus, a new model was suggested to improve the problem, which has a combined body that of a flagpole and a buoy Three new models of CL-L (long and thin cylinder), LF (leaf shape) and LF-F (leaf shape with fin) were designed. Also a cylinder type (CLD) with a flagpole as a control was included in the experiment. As a result, the LF-F had the smallest tension and a half tension of the CLD. Therefore, it is supposed that the flagpole and buoy combined model could reduce the tension on buoy rope and contribute to improve the gillnet loss problem.
        4,000원
        28.
        2016.05 KCI 등재 구독 인증기관 무료, 개인회원 유료
        Mobile fish-cage was developed assuming a cage net with an enclosed area, which and estimated the hydrodynamic characteristics of the cage through the model experiment. Flux-shielding plates, installed in the bow were compared with the resistance test carried out by making a hole, bilge keel and stud, and basic block flow rate consisting of the results to a flat surface plate. The experimental results confirmed the improved resistance performance effect of 3~6% in the bilge keel and the stud form. To assess the stability of the fish-cage, evaluation of the stability in accordance with the stability criteria for determining the floating docks had confirmed that it satisfied the static stability performance under operating conditions at sea.
        4,000원
        29.
        2015.12 KCI 등재 구독 인증기관 무료, 개인회원 유료
        The Fishing gear loss has been repeated every year in the West Sea; however, there has been no solution. So fisher men have undergone economic loss every year. Thus it is required to reduce the loss of fishing gear. In this study to find out the reason that the fishing gear is lost in the Sea, 10 years data of wave and current for 6 locations in the West Sea were investigated and a numerical modelling were conducted into the behaviour of a gillnet in wave and current. The fishing gear was modelled with the mass spring model. As a result, it came out into the open that the location where fishing gear loss occurred most frequently was Choongnam province. The height of the maximum significant wave in this province was 6.7 m and the period of that was 4.4 second. The maximum current speed was 0.7 m/s. As a result of simulation with these data, it was revealed that the buoy is one of the reasons to decrease the holding power of the gillnet. For example, the tension of anchor rope was decreased to 50% while the drag coefficient or volume of buoy was decreased to 25%. So it is predicted that an improvement of the buoy contributes to the reduction of the gillnet loss.
        4,600원
        30.
        2015.08 KCI 등재 구독 인증기관 무료, 개인회원 유료
        In an attempt to find the improvement of the fishing efficiency according to the hull form remodeling for the 3 tuna purse seiner, the Catch-Per-Unit-Effort (CPUE) for that undertaken before (2008) and after (2010) was analyzed. In addition, the CPUE of 6 similar ships operated same period and same fishing ground. As result, it came to verify that the three modified ships had a significant value on the CPUE. An another index for the improvement of fishing efficiency is the rate of reduction of fuel oil consumption for the modified ships. Fuel oil consumption per day in service speed as comparing with the original ships were reduced 2.1%, 4.0% and 5.1% on the modified ship A, B, and C respectively. And each ship’s service speed was increased 1.0 kt, 0.6 kt, and 0.4 kt according to the modified ship A, B, and C in due order. In the conclusion, the remodeling job with newly equipped bulbous bow, lengthened slipway and enlarged rudder area were improved fairly much on fuel oil efficiency, the ship’s speed, and in the end, that led to the improving fishing efficiency. Hence, the remodeling of tuna purse seiner come to improve not only the fishing performance, but contribute to the reduction of operating cost by saving energy for the fisheries industry.
        4,300원
        32.
        2015.02 KCI 등재 구독 인증기관 무료, 개인회원 유료
        In an attempt to improve the maneuvering character of hull form renovated tuna purse seiner. A renovation was carried out on the 3 tuna purse seiner fishing vessel. To grasp the progress of maneuvering and resistance on ship B (730 ton class), new bulbous bow was only attached. The ship A (740 ton class) and C (600 ton class) were modified for new bulbous bow, enlarged slipway and rudder. And then the zigzag and the turning test were carried out. According to the turning test, the advance and the tactical diameter were improved very much for the modified ship. The sea trial was carried out for the original and modified ship A. It is showed that the results of sea trial corresponded with that of the tank test on the whole. In the result of the zigzag test on ship B, the turning ability was improved very much, but the yaw checking ability was deteriorated in just some degree. In the result of the zigzag test on ship C, the turning ability and yaw checking ability were remarkably improved. Ship C was greatly improved among the three ships for the maneuvering character of modified hull form.
        4,000원
        33.
        2014.12 KCI 등재 구독 인증기관 무료, 개인회원 유료
        In this study, the stability of fishing vessels get some change in accordance with the installation of LED luring lamp in comparison with metal halide luring lamp were investigated. Inclining test for 9.77 ton class of squid jigging and hair-tail angling vessel was performed in order to make a stability evaluation. A performance analysis of the target vessels to the stability on the basis of KST-SHIP program was evaluated. The results were as follows in this study. The stability of the fishing vessel by a metal halide such as LED and the like according to the result obtained by the inclining test is a slightly present difference, and the stability is not affected. The fishing vessel with LED lamp installed satisfies all the stability criteria specified in law and IMO rule. Compared to the metal halide LED lamp the increase of the height of the center of gravity and the initial transverse metacenter was caused. Due to the LED installation, the somewhat wider wind area of the waterline, which appears as a result, does not lead to an actual increase in rolling period. But then it is necessary to be designed on that the LED lamp shape reduces wind pressure area. Because of LED lamp installation, the GM value of vessels is increasing faster rolling cycle so causes a decrease in the sense that the crew is aboard.
        4,000원
        34.
        2014.12 KCI 등재 구독 인증기관 무료, 개인회원 유료
        This study describes the result on PV system for evaluating the performance of small fishing boats. Photovoltaic system with 200 watts power generation facilities on the 3-ton fishing boat was carried. Load test was performed on the condition that the work lamps lit during night operations. As a result the performance can be used for more than two hours at 60 watt work lamps. The load test was performed on the condition that fishing vessels are on the cruising condition at sea. The solar power systems have been investigated as a power generation efficiency of about 36.55%. Additional tests show that the power generation efficiency is difficult to expect a maximum of 50% or more.Fuel consumption of fishing boats by installing a solar power system is reduced. Also the PV system is useful for the verification of their availability for fishing vessels as well as the satisfaction of the fishermen. The results for the durability of the photovoltaic device is acceptable, including a solar panel, controller and the performance exhibited no breakage in the harsh marine environment or failure so far. The installed PV system was confirmed that the durability with at least 2 years.
        4,000원
        35.
        2014.08 KCI 등재 구독 인증기관 무료, 개인회원 유료
        The difference of mooring tension by type of buoy was investigated in the circulating water channel and the wave tank for deducting the most stable buoy from the current and the wave condition. 5 types of buoy made up of short cylinder laid vertically (CL-V), short cylinder laid horizontally (CL-H), capsule (CS), sphere (SP) and long cylinder (CL-L) were used for experiments. A mooring line and a weight were connected with each buoy. A tensile gauge was installed between a mooring line and a weight. All buoy’s mooring tension was measured at the same time for the wave test with periods of 1.5~3.0 sec and wave heights of 0.1~0.3 m, and the current test with flow speeds of 0.2~1.0 m/sec. As a result, the order of tension value in the wave test was CL-H > CL-V > SP > CS > CL-L. In the current test CL-V and CL-H were recorded in the largest tension value, whereas SP has the smallest tension value. So it seems that SP buoy is the most effective in the location affected by fast current. CS is predicted to be suitable for a location that influence of wave is important more than that of current if practical use in the field is considered. And it was found that the difference of mooring tension among buoys in wave is related to the product of the cross sectional area and the drag coefficient for the buoy’s bottom side in high wave height. The factor for the current condition was not found. But it was supposed to be related to complex factors like a dimension and a shape by buoy’s posture to flow.
        4,200원
        36.
        2014.05 KCI 등재 구독 인증기관 무료, 개인회원 유료
        The sea cage in marine aquaculture might be varied such as on the stability and shape in the open sea by environmental factors. To evaluate the stability of net cage structures in the open sea, the physical and numerical modeling techniques were applied and compared with field observations. This study was carried out to analyse the stability and the volume loss which would have an effect on the fish swimming behavior in the octagonal pillar type fish cage under the open sea. As a results, the volume loss ratio of the fish cage as measured using a depth sensor was indicated a value of the 30.3% under the current velocity (1.1m/s). The fish cage should be consisted of a concrete block with a weight over 10 tons, a mooring rope diameter over 28mm PP, and a shackle of 25mm under the current speed of 1m/sec for reasonable stability.
        4,000원
        37.
        2012.05 KCI 등재 구독 인증기관 무료, 개인회원 유료
        In head sea, a ship has mainly the longitudinal motion such as vertical acceleration and pitch. In that case, the motion characteristics of a ship will have changed as the location different from each of place vertically and horizontally on board. The author carried out an experiment about the ship's vertical acceleration and pitch according to the location for the head sea, and analyzed the data with the aid of the statistical and spectral analyzing method to get the motion characteristics of the vessels. The response of vertical acceleration and pitch not deeply depend on the decks vertically, but displayed the relative big different value horizontally even if same deck. The biggest response of vertical acceleration and pitch among the accommodations was shown at scientist room, but the value of it not reached to the minimum requirement of ISO 2631-1 for working on board.
        4,000원
        38.
        2012.02 KCI 등재 구독 인증기관 무료, 개인회원 유료
        This study aims to analyze the performance of a submersible fish cage which was designed for developing an economical cage system can be applied in korean aquaculture environment easily. To analyze the performance of the designed cage a model test was carried out. In the test, inclination changes of the upper frame and mooring tensions of model cage were measured during the submerging and surfacing motion in still water and wave condition (period: 2s, wave height: 0.1, 0.2, 0.3m). As a result, in the still water condition the model cage kept horizontal balance and inclination degree of the upper frame was about 1˚. In the wave condition, the model cage showed bilateral symmetric up-and-down motion but the average inclination degree of the upper frame was about 0˚. When the model cage reached at a depth of 1m, the up-and-down motion of the cage was decreased by 12% compared with that of at the surface (period 2s, height 0.3m). In the same wave condition, the maximum and average line tension under the bottom position were about 8% and 11% respectively compared with that of at surface.
        4,200원
        39.
        2011.11 KCI 등재 구독 인증기관 무료, 개인회원 유료
        In an attempt to respond to the increase in international oil prices and reduce operating expenses, ship remodeling was carried out on a 740ton class tuna purse seiner. To strengthen the competitiveness of the fisheries industry by improving vessel performance, a bulbous bow was newly equipped. The slipway and rudder area were also lengthened and enlarged with the propeller and main engine remained unchanged. To reduce the hull resistance, a circle type bulbous bow was attached on the hull behind bow thruster and thus the cost for exchanging electrical equipment for bow thruster was reduced. The new rudder area was expanded 15% more than the old one within the extent that the existing mechanical control part and rudder stock were not changed. To prevent fishing net damage and stabilize wake field, slipway was lengthened to the optimal position. All of the new design of remodeling parts went through the model tests in towing tank and CWC. Besides resistance test, all of necessary model test results were delivered for hydrodynamic character for the modified ship. The maneuvering simulation to verify that the remodeled ship satisfies the IMO rules was performed in both zigzag and turning tests. The estimated resistance with new bulbous bow and lengthened stern was reduced by 4.8% in the 2-dimensional analysis and 17.4% in the 3-dimensional analysis in comparison of conventional ship. The average reduction of resistance was estimated about 10%. Maneuvering character of modified hull form was found to satisfy all regulations under IMO. The remodeling of tuna purse seiner can not only improve fishing performance but also contribute to reduction of operating cost by saving energy for the fisheries industry.
        4,000원
        40.
        2011.08 KCI 등재 구독 인증기관 무료, 개인회원 유료
        This study was performed to develop a video based system which can be used to measure the averaged fish size in a non-intrusive fashion. The design was based on principles of simple stereo geometry, incorporated fish dimensions weight relationships and took into consideration fish movement to lower system costs. As the fish size is an important factor that impacts the economy of an aquaculture enterprise. Size measurements, including fork length, width or height, girth, thickness and mass, can be used to determine fish condition in the fish farm, so the averaged fish size of fish cage needs to consistently monitor in open ocean aquaculture cage. A precision of ±3% for replicate length measurements of a 60cm bar is obtained at distances between 2.0 and 6.0m, and the mean fork length and mean swimming speed of bluefin tuna were estimated to 48.8cm and 0.78FL/s, respectively.
        4,000원
        1 2 3