본 연구에서는 콘크리트내로 침투하는 염소이온을 모니터링하기 위하여, 스크린프리트 기법으로 염소이온 반응형 부식센서를 개발하고, 센서의 세선 수가 부식반응도 및 민감도에 미치는 영향을 실험을 통하여 정량적으로 분석하였다. 개발된 부식센서를 이용하여 염소이온량에 따라 부식 반응도을 확인하였으며, 센서의 파괴정도에 따른 저항변화에서는 단선형 센서보다 다선형 센서에서 큰 저항 변화를 나타내었다. 또한, 부식센서는 NaCl 수용액의 농도가 높은 만큼 센서의 저항변화가 크고, 콘크리트 내에서 센서 종류에 따른 부식저항은 단선형보다 다선형에서 민감도가 높게 나타났으며, 센서의 매설깊이가 클수록 저항변화 사이클 (cycle)은 증가하였다. 이상의 결과로, 본 연구에서 개발된 부식센서는 염분에 대한 부식반응과 민감도, 저항의 변화를 감지할 수 있었으며, 특히 7세선이 우수한 결과를 나타내어, 염분의 침투정도를 모니터링 하는데 가장 적합하다고 판단된다.

On this study, carbonation rate and W/C ratio were estimated by collecting actual data of each carbonation depth and compression strength from inner wall, outer wall, stair hall, and balcony floor of certain remodeling apartments. Through above tests, this study can be reference data of the method of life time prediction for the apartments that subject to remodeling.

In recent years, High-Rise buildings are increased. For this reason, using large size member of framework is inevitable. High hydration heat which is caused by large size member of framework makes structure to take serious risk of durability. To solve this problem, a variety of researches are proceeding. Recently, several studies about decreasing cement hydration heat by using Urea are reported. In this study, thermal performance evaluation experiment conducted on cementious materials using urea. In addition, hydration heat is predicted through theoretic consideration and conducted comparative analysis of difference between the results from experiment and theoretic prediction. Results of experiment showed hydration heat was decreased by increasing amount of urea addiction. Through a comparative analysis, error range is included in plus or minus five percent in the dissolution test and thermal performance evaluation test of cement mortar.

본 연구는 조강시멘트와 경화촉진제를 사용하여 조기강도 발현의 메커니즘을 분석하는 것이 목적이다. 연구결과 경화촉진제는 시멘트와의 수화반응시 Ca(OH)2의 촉진시키는 것을 TG/DTA 실험을 통하여 검정하였다. 압축강도 측정결과 경화촉진제의 사용량이 증가 할수록초기압축강도가 증가하는 것을 알 수 있었다. 또한 미소수화열 측정결과 경화촉진제는 시멘트의 성분중 C3S의 수화반응을 촉진시키는 것으로 나타났다. XRD분석결과 재령별 수화생성물을 확인할 수 있었으며 경화촉진제의 사용량이 증가할수록 수화물들의 피크점이 높게 나타나는 것을 알 수 있었다. SEM찰영을 한 결과 촉진제의 첨가량에 따라 Ca(OH)2의 생성과 재령에 따라 C-S-H의 형상을 관찰할 수 있었다.따라서 본 연구에서 사용된 경화촉진제는 초기강도발현 시키는 것에 대해 효과적인 것을 확인 할 수 있었다.

This study is based on the electrochemical theory which aims to get the quantitative evaluation about corrosion protection of Zn-Sn metal spray method. The various existing corrosion resistance method and various mixture ratio of Zn-Sn metal spray method is applied with structural steel which is measured change of polarization resistance and corrosion potential. So corrosion protection of Zn-Sn metal spray method is tested. Consequently, coating side of Zn-Sn metal spray method was lower than electric potential of a structural steel adhesion side. So, Galvanic Protection of Zn-Sn metal spray found that structural steel advanced system. Accordingly, Zn-Sn metal spray method is expected as corrosion protection technology excellent in corrosion prevention of structural steel.

The purpose of this study is to evaluate the corrosion protection properties of Zn/Sn metal spray method according to the contents ratio of Zn and Sn by CASS test. Also, the corrosion protection life of Zn/Sn metal spray method is evaluated by the comparing between the corrosion properties of Zn metalizing method and Zn/Sn metal spray method using CASS test. As a result, it was confirmed that the optimum content ratio of Zn/Sn in metal spray method is 60:40(65:35) (Zn : Sn volume ratio) in aspect of corrosion protection properties and construction properties. Also, it was confirmed that the Zn/Sn metal spray method had more than 3 times of corrosion protection properties cmparing the Zn matalizing method.

On this study, carbonation rate and W/C ratio were estimated by collecting actual data of each carbonation depth and compression strength from inner wall, outer wall, stair hall, and balcony floor of certain remodeling apartments. Through above tests, this study can be reference data of the method of life time prediction for the apartments that subject to remodel.

The main purpose of this study is to provide fundamental data in reducing thermal cracks of mass concrete by using Urea. Substitution methods of Urea mixed concrete was different from existing substitution method of concrete. Therefore existing research for Urea mixed concrete had no definite criterion in performance evaluation. In this research, setting-up new criteria, Urea/Water ratio, when evaluating experiment results. As result of experiment, Cement Paste flow was increased largely when mixed in addition method. But there were almost no differences in degree of temperature reduction and time-delay.

Blast furnace slag is recycled as high value-added material, while steel slag is difficult to recycle or is recycled as low value-added one relatively due to its expansion collapsability. It's property is caused by the high content of Free-CaO and unstable steel oxides. Currently, a technique to subdivide the process refining is introduced, can be divided into the electric furnace steel slag and reducing steel slag. In this study, Free-CaO in the electric arc furnace slag by the ethylene glycol method for the quantitative evaluation for the expansion to proceed with construction materials, electric arc furnace slag oxidation is to use.

In this study, corrosion potential (Ecorr), corrosion rate, and polarization resistance were measured aimed at inorganic inhibitors (passive film type) and organic inhibitors (absorption type). The experiment was conducted using potentiostat for the variable molar ratio and chloride ion concentration of the components of inhibitors in an aqueous solution of saturated calcium hydroxide targeting corrosion. As a result, it was possible to ensure an anticorrosive performance of at least a 1.2 molar ratio of inorganic inhibitors. Also, the organic inhibitors ensured the prevention of the anticorrosive performance of at least about a 0.3 molar ratio. It also showed the tendency that between polarization resistance and corrosion rate, Ecorr and corrosion rate is inversely proportional to the linear. Conversely, the tendency between polarization resistance and Ecorr is proportional to the linear. Also, a distinct difference in organic and inorganic inhibitors’ relationship to Ecorr, corrosion rate, and polarization resistance was not shown.

These researchers are studying on the hydration model suggestion of cement incorporating blast furnace slag in durability prediction of concrete using hydration model. So in this study it measured hydration heat according to replace ratio, water cement ratio using conduction calorimeter to acquire experiment data for experimental verification and verify hydration heat property when blast furnace slag is incorporated.

To predict the characteristics of chloride ion penetration in the concrete and rebar corrosion prediction for chloride ion permeation, it is important to understand the chloride ion diffusion coefficient. It is possible that the reinforced concrete structures can be predicted accurately by the profile of the position of the rebar chloride ions using a chloride ion diffusion coefficient. On this study, analysis of chloride ion diffusion coefficient experimented in Korea and the effect of changes in the surface chloride ions concentration on chloride attacked durability design was analyzed

To the goal of improving the early compressive strength of the mortar including Ground granulated blast furnace slag under low-temperature environment, Industrial byproducts including SiO2 and Al2O3 was fired and than 7% of it was added into Ground granulated blast furnace slag. By checking compressive strength and activity index from different mixing rate, in spite of low strength development than OPC 100%, when using firing powder, the expectation of increasing strength by curing time was affirmative

In this study, we investigated the physical properties and thermal behaviors of specimens that applied different mixing ratios of foaming agent to evaluate the possibility of use in the structural elements. We proposed the estimating equation for compressive strength of each mix having different ratio of foaming agent. We also confirmed that the density of cement matrix is decreased as the mixing amount of foaming agent increase up to 0.6% of foaming agent mixing ratio which was observed by SEM. Based on porosity and compressive strength of control mortar without foaming agent, we built the estimating equations of compressive strength for mortars with foaming agent

In this experiment, the high early strength cement containing massive C3S quantity was used to enhance the early strength of cement mortar using admixtures which can accelerate C3S hydration reaction in the condition of room temperature. The measuring items are zero flow, setting times, compressive strength and analysis of MIP & SEM

In this study, in order to comprehend performance of corrosion inhibitor, the experiment study was conducted about corrosion characteristic 3 steps(0.0, 0.6, 1.2) of Chloride by added amount of inorganic(Ca(NO2)2) and organic(DMEA) corrosion inhibitor by the corrosion inhibitor types about 0.6kg/m3, 2.4kg/m3 based on Chloride ion content 1.2kg/m3 for service life prediction of concrete structure by using Poteniostat. As a results, the excellent anti-corrosive performance of organic corrosion inhibitor was seen that absorption types organic corrosion inhibitor has excellent anti-corrosive performance compared to the inorganic nitrous acid corrosion inhibitor by the added amount of corrosion inhibitor

In this study, in order to comprehend performance of corrosion inhibitor, the experiment study was conducted about corrosion characteristic of 3 steps(0.0, norm 1/2, norm) compared to organic corrosion inhibitor standard use of liquid and molar 3 steps(0.0, 0.3, 0.6%) of Chloride by added amount of inorganic corrosion inhibitor by the corrosion inhibitor types about 2.4kg/m3, 4.8kg/m3 based on Chloride ion content 1.2kg/m3 for service life prediction of concrete structure by using Poteniostat.

Temperature of fresh concrete can be effectively used to predict the strength of concrete being cured and make an informed decision for stripping the molds. A hygrothermograph and thermo-couple sensors that require an extensive wiring have been applied to measure a temperature of concrete at the early stage of the curing process on site. Therefor, this study on the strength prediction using Maturity is mainly focused on, but the study on the concrete mixing blast furnace slag powder is insufficient. The purpose of this study is to investigate the relationships between compressive strength and equivalent age by Maturity function and is to compare and examine the strength prediction of concrete mixing Blast Furnace Slag Power using ACI and Logistic Curve prediction equation.

최근water front나 자연형 하천의 개발이 많아지는 가운데 해안에 인접한 하천설계에 있어 일반적으로 기점 홍수위가 만조 시 수위보다 높게 계산되면 조석의 영향을 고려하지 않고 기점 홍수위만으로 수리해석을 하는 경우가 대부분이다. 그러나 본 연구는 기점 홍수위가 만조 시 수위 보다 높더라도 밀려오는 조류의 영향으로 하천 기점 홍수위의 변화를 야기시킬 수 있을 것이라 판단하여 부산의 지방하천인 온천천이 조석현상에 의해 어떤 흐름의 변화가 발생하는지를 Delft-3D를 이용하여 분석하였다. 수치해석 결과 하류 경계조건에 조석영향을 고려하였을 경우 하천의 일정범위까지 수위가 조석의 주기성을 나타내었고 하천 상류방향으로 수위 변동범위가 확대되었다.

콘크리트 내부에 매설된 철근의 부식은 철근콘크리트구조물의 조기 성능저하와 붕괴의 주요원인이 되고 있다. 철근콘크리트 구조물에 발생하는 열화현상 중에서 철근부식에 의해 발생되는 염해는 그 피해가 다른 열화 현상보다 심하고 구조물의 보수 및 시공 측면에서도 막대한 경비가 요구되고 보수시기 또한 정하기 힘들다. 따라서 철근의 부식상태에 대한 조기발견은 관리자의 효율적인 보수 및 보강계획 수립을 위해 매우 중요하다. 한편 철근 부식을 평가하는 방법 중 비파괴측정이 많이 사용되고 있다. 특히 CM-Ⅱ(corrosion meter) 측정기는 자연전위와 분극저항 및 콘크리트 비저항을 측정할 수 있어서 많이 사용되지만 몇 가지 단점을 가지고 있다. 이러한 단점을 극복하기 위해 매립형 미니센서가 개발되어져 왔다. 이 미니센서를 이용하여 철근 부식을 측정한 후 CM-Ⅱ(corrosion meter)의 측정결과와 비교분석하여 개발된 미니센서의 타당성을 검증하였다.