W2C is synthesized through a reaction-sintering process from an ultrafine-W and WC powder mixture using spark plasma sintering (SPS). The effect of various parameters, such as W:WC molar ratio, sintering temperature, and sintering time, on the synthesis behavior of W2C is investigated through X-ray diffraction (XRD) analysis, scanning electron microscopy (SEM) analysis of the microstructure, and final sintered density. Further, the etching properties of a W2C specimen are analyzed. A W2C sintered specimen with a particle size of 2.0 μm and a relative density over 98% could be obtained from a W-WC powder mixture with 55 mol%, after SPS at 1700℃ for 20 min under a pressure of 50 MPa. The sample etching rate is similar to that of SiC. Based on X-ray photoelectron spectroscopy (XPS) analysis, it is confirmed that fluorocarbon-based layers such as C-F and C-F2 with lower etch rates are also formed.

PURPOSES : The objective of this study is to understand blow-up distress and causes in concrete pavement. METHODS : Feasible causes of blow-up and existing models were reviewed based on the literature. Three analytical models were adopted to perform a sensitivity analysis. Input parameters reflected the typical concrete pavement of national expressways. Evaluation of blow-up models was based on the amount of temperature increase and zero stress temperature of the concrete pavement. RESULTS : A review of the literature indicated that the five major causes of blow-up were: increase in temperature and solar radiation, alkaliaggregate reaction (AAR), friction characteristics between the concrete slab and subbase, joint closure (incompressible), and joint freezing. The sensitivity analysis revealed that the coefficient of thermal expansion had the greatest influence on the blow-up safety temperature. CONCLUSIONS : From existing blow-up model results, it could be concluded that the construction of concrete pavement during the winter season was not effective at preventing blow-up. In addition, an equivalent coefficient of thermal expansion that considers slab expansion due to AAR was proposed as a model input parameter for concrete pavement sections damaged by AAR.

This study aimed to establish the public interest functions of fisheries and fishing villages, which is intended to help introduce and expand the public-purpose direct payment system in the fisheries sector. Firstly, this study looked at trends related to the public interest functions of domestic and foreign cases in similar fields in order to get implications for establishing public service functions in fisheries and fishing villages. Secondly, three criteria were defined for establishing the public interest functions of fisheries and fishing villages. Thirdly, the public interest functions of fisheries and fishing villages were defined through prior research, analysis of overseas cases, and consultation with experts in the fields of fisheries and fishing villages. As a result, the six public interest functions and the 14 detailed functions were defined. Finally, this study established a direction for preserving and improving the public interest functions of fisheries and fishing villages, and presented strategies for achieving them.

In Korean traditional architecture, the Gong-po style is divided into the Jusimpo, Dapo and Ikgong. Jusimpo and Chulmok-Ikong, where only Gong-po is placed on the column, differ in form of Gong-po depending on the viewpoint. Since ‘Chulmok-Ikgong’ has been generally regarded as ‘One Chulmok-Two Ikgong’, the precedent researches have been conducted mainly on ‘One Chulmok-Two Ikgong’ in the Gong-po style classification. However, when it comes to ‘One Chulmok’, the style of Ikgong can be organized from the one to three steps and this study is particularly for examining the occurrence and transformation of ‘One Chulmok-One Ikgong’. One of the case study sites, Bonghwa Cheongamjeong was originally built in the 16th century, and is believed to have been repaired from ‘Non Chulmok-One Ikgong’ to ‘One Chulmok-One Ikgong’. Since the beam linked directly to the upper part of a capital, it does not connect the eave trave(architrave) in between. Also, Soro which supports Jangyeo(the architrave strip) has been placed and linked in comparatively lower position. It is confirmed by the signigicant difference in the hierarchy of Gong-po forms in one architecture. The Jeonju-Hyanggyo Daeseongjeon, which was built in the 17th century among the subjects, was similar with ‘One Chulmok-One Ikgong’, but it was found to be the type of Jusimpo form because the bottom of the beam and the top of the Ikong are apart. And Gongan is confirmed at Cheomcha. In the 17th century, it can be seen that Heot-Cheomcha disappeared and Ikgong was started to use as a constant figure. The end of the 18th century, it can be seen that it was changed into a ornament added on Haeng-gong, being seen in the case of Hwaseong Dongjangdae. In conclusion, it can be seen that ‘One Chulmok-One Ikgong’ were developed in both the Jusimpo and Ikong style. The transformation into ‘One Chulmok-One Ikgong’ was inevitable consequence related with an elevation difference between the eave trave and the column trave.

PURPOSES : This study deals with a pressure relief joint, which is one of primary preventive methods of blow-up in concrete pavement. The purpose of the study is to estimate the joint sealant protrusion of pressure relief joint filler types according to horizontal displacement of concrete pavement by applying a variety of joint sealants and joint fillers. And test method for resistance of concrete to chloride ion penetration and test method for resistance of concrete to rapid freezing and thawing were conducted to analyze the improvement of concrete durability according to the primer types on concrete surface of stress relief joint. METHODS : Joint fillers of pressure relief joint were categorized into four different types, which are was styrofoam+backer+sealant(type 1), styrofoam+sealant(type 2), foaming styrofoam+sealant(type 3), and preformed joint+sealant(type 4). By varying the depth (10, 20, 30, 50 mm) from the top of the test specimens to the sealant’s surface, the test factors were evaluated for a total of 16 variables. When the specimen’s joint spacing decreased from 70mm to 10mm, the load was stopped. And the displacement of the center of the joint protrusion was measured. The test was terminated when the specimen joint spacing was reduced to 60 mm. The horizontal displacement at the time when the joint protrudes over the specimen surface is recorded and analyzed as the critical threshold displacement. RESULTS : According to the test results according to the type of joint filling material, it was found that there was a difference in the protrusion of the horizontal compression displacement according to the joint filling type. Under the current installation standard of 20mm, the preformed seal joint member showed the best crimping characteristics by securing the safety against protrusion until the horizontal displacement of 50mm occurred. CONCLUSIONS : The most common failures in pressure relief joints are those related to joint sealants, which can be minimized by changing the current joint type, installation depth, etc. to suppress them.

This study conducted the experiment for the development of the low pressure type SCR system. The experimental equipment of SCR system was installed, which was widely used as the nitrogen oxides abatement system, and the demonstration experiment was conducted to see that it met the Tier III regulation according to the IMO NOx Technical Code. The SCR system demonstration experiment was divided into three stages: SCR system component operation test, engine parameter test by engine load, and NOx abatement performance and ammonia slip verification test. The final performance of the SCR system was verified through analysis of NOx abatement performance and ammonia slip test results for each load variation.

본 연구에서는 다소비 농산물인 사과, 복숭아, 딸기의 품종에 따른 수용성 비타민 B군 중 B1, B2 및 나이아신을 분석하여 함량 차이를 비교하고, 식품성분표의 기초자료로 활용하고자 하였다. 품종에 따른 사과의 비타민 B1 함량은 0.063-0.208 mg/100g, 비타민 B2 함량은 0.006-0.031 mg/100g의 범위의 값으로 검출되었으나, 나이아신은 검출되지 않았다. 품종에 따른 복숭아의 비타민 B1 함량은 0.014-0.276 mg/100g, 비타민 B2 함량은 0.019-0.042 mg/100g, 나이아신 함량은 0.298-1.096 mg/100g 범위의 값으로 검출되었다. 품종에 따른 딸기의 비타민 B1 함량은 0.112-0.394 mg/100g, 비타민 B2 함량은 0.001-0.027 mg/100g, 나이아신 함량은 0.388-0.809 mg/100g 범위의 값으로 검출되었다. 따라서 사과, 복숭아, 딸기 등의 과일의 영양성분 분석 데이터베이스 구축시 품종 요인을 고려할 필요가 있다고 판단된다. 이와 더불어 과일의 수확시기, 재배방법, 환경적인 요인에 따른 차이가 있을 것으로 판단되며 그에 따른 추가적인 연구가 필요하다.

본 연구는 2005년부터 2018년까지 14년간 주암호에서 출현한 남조류의 천이 양상을 분석하여, 남조류에 영향을 미친 주요 환경요인과의 관계를 파악하고자 연구를 수행하였다. 특히 2012년 이후 유해남조류 (Harmful algae) 출현량 급감의 원인을 파악하고자 하였다. 조사기간 동안 두 지점의 유해남조류 현존량은 주암댐: 10~24,891 cells mL-1, 신평: 13~26,043 cells mL-1의 범위로 출현하였다. 전반기 시기 두 지점의 평균 현존량은 각각 2,575 cells mL-1, 2,557 cells mL-1로, 이는 후반기 시기 평균 현존량 (42 cells mL- 1, 82 cells mL-1)에 비해 약 60배, 30배의 큰 세포수 차이를 보였다. 남조류가 상대적으로 많이 출현하는 여름 시기 (6~9월)를 대상으로 상관분석을 실시한 결과, 유해남조류는 TN, 방류량, 저수량과 양의 상관관계를 보였고, 전기전도도와는 음의 상관관계를 보였다. t-검정 결과 TN, EC, 체류시간의 유의미한 차이를 확인하였다. 특히 TN은 0.566~1.292 mg L-1의 범위로 평균 0.862 mg L-1로 보였다. 전반기, 후반기 평균 TN은 전반기 0.912 mg L-1, 후반기 0.811 mg L-1로 감소하였다. 또한 유의확률은 다소 떨어지지만, TP의 경우 평균 차이는 없으나 표준편차가 비교적 큰 차이를 보여 변동성이 큼을 알 수 있었다. 강우량이 집중된 여름 (6~9월) 시기의 전반기와 후반기 강우량 감소하는 패턴이 원인인 것으로 판단된다 (전반기 263.3 mm, 후반기 219.9 mm). 즉, 전반기에 비해 강우량은 감소 하였으며, 이로 인해 TP의 변동성이 감소되었다고 판단된다. TP의 변동성의 감소로 인해 전반기에 남조류의 luxury consumption이 가능하여 남조류의 성장률이 높았을 것으로 추측된다. 따라서 주암호 유해남조류 감소 원인은 강우량의 감소로 인한 영양염의 감소 (TN) 및 변동성의 감소 (TP)의 결과로 사료된다.

In the development of advanced ceramic tools, material improvements and design freedom are critical in improving tool performance. However, in the die press molding method, many factors limit tool design and make it difficult to develop innovative advanced tools. Ceramic 3D printing facilitates the production of prototype samples for advanced tool development and the creation of complex tooling products. Furthermore, it is possible to respond to mass production requirements by reflecting the needs of the tool industry, which can be characterized by small quantities of various products. However, many problems remain in ensuring the reliability of ceramic tools for industrial use. In this study, alumina inserts, a representative ceramic tool, was manufactured using the digital light process (DLP), a 3D printing method. Alumina inserts prepared by 3D printing are pressurelessly sintered under the same conditions as coupon-type specimens prepared by press molding. After sintering, a hot isostatic pressing (HIP) treatment is performed to investigate the effects of relative density and microstructure changes on hardness and fracture toughness. Alumina inserts prepared by 3D printing show lower relative densities than coupon specimens prepared by powder molding but indicate similar hardness and higher fracture toughness values.

In this study, real-time monitoring of air quality using a real-time mobile monitoring system was conducted to identify the emission characteristics and current status of air pollutants and odorous substances that are mainly generated in domestic dyeing industrial areas and to trace the pollutant sources. The concentration of toluene in the industrial area was detected up to 926.4 ppb, which was 3 to 4 times higher than that of other industrial areas. The concentration of methylethylketone was 124.7 ppb and the concentration of dichloromethane was 129.5 ppb. Acrolein concentration was highest at E point at 521.6 ppb, methanol concentration was highest at D point at 208.8 ppb, and acetone concentration was highest at M and N points at 549.3 ppb. The most frequently detected concentration of pollutants in the air quality monitoring results in the industrial area was, in descending order, toluene > methanol > acrolein > dichloromethane > acetone, which was similar to the chemical emissions used in the industrial area by the Pollutant Release and Transfer Register data. The concentration of odorous substances measured in real time was compared with the concentration of minimum detection, and the concentration of hydrogen sulfide was about 10 times higher than the concentration of minimum detection at A point, which was judged to be the main odorous cause of A point. In the future, if the real-time mobile measurement system is constructed to automatically connect wind direction/wind speed, PRTR (Pollutant Release and Transfer Register) data and SEMS (Stack Emission Management System) data, etc., it was judged that more accurate monitoring could be performed.

본 연구는 최적의 당화 조건을 구명하기 위해 양파즙과 양파박을 0, 10, 20%로 첨가했다. 처리별로 25, 30, 35℃에서 72시간 동안 당화시켰다. 35℃의 당화 온도에서 처리 24시간 후 양파즙 첨가 20%에서 13.2 ◦Brix, 양파박 첨가 20%에서 19.6 ◦Brix의 당도를 나타내었다. 그러나 관능 평가결과 처리 간에 크게 차이가 나지 않았다. 양파박을 사용한 양파 당화물이 염증 유발물질인 히스타민 방출량을 14% 억제하는 효과를 나타내었다. ELISA 분석 결과 양파당화물이 대조군에 비해 IL-8과 TNF의 방출을 보다 효과적으로 차단할 수 있었다.

This study was carried out to standardize the material properties of roll-over protective structure (ROPS) for agricultural tractor. The material properties which were obtained from stress-strain curve, a result of tensile test stress, were used to apply to the virtual test and varied from one production lot to the other and from one manufacturer to the other. And the finite element analysis was performed on the ROPS according to the OECD code. The results show that the load-displacement curves of virtual test were approximately equal to the actual test curves. The manufacturer or lot has been shown to have little effect on the properties of the material. Therefore, it is expected that the representative values that can be used in the finite element analysis can be determined by averaging the property values.

This study demonstrates the effect of addition of Fe particles of different sizes on the critical properties of the superconductor MgB2. Bulk MgB2 is synthesized by ball milling Mg and B powders with Fe particles at 900oC. When Fe particles with size less than 10 μm are added in MgB2, they easily react with B and form the FeB phase, resulting in a reduction in the amount of the MgB2 phase and deterioration of the crystallinity. Accordingly, both the critical temperature and the critical current density are significantly reduced. On the other hand, when larger Fe particles are added, the Fe2B phase forms instead of FeB due to the lower reactivity of Fe toward B. Accordingly, negligible loss of B occurs, and the critical properties are found to be similar to those of the intact MgB2.