PURPOSES : For high driving performance and service life of cement concrete pavement, construction quality must be secured. The construction quality is to be measured after pavement construction, but in this case, it is difficult to improve construction quality. Therefore, it is necessary to develop a method for measuring and correcting the profile of the pavement and subbase so that the construction quality can be monitored immediately after construction. METHODS : The device that can measure the construction quality of cement concrete pavement has been developed. Through the experiment simulating the field situation, the profile of the pavement and subbase was measured and calibration method was developed. RESULTS : In the measured profile, an outlier by the sensor and noise by the sensor and vibration were measured, and a step-like profile was measured differently from the acture one. To remove outliers, the boxplot outlier removal method was applied by overlapping each data group. The noise were removed by a low pass filtering. And, it was calibrated to a profile similar to the acture one through the sampling interval adjustment and the weighted moving average method. CONCLUSIONS : The method that can measure and calibrate the profile that is almost identical to the actual one has been developed. Accordingly, it is expected that the performance of the pavement can be improved by accurately monitoring the construction quality immediately after construction.

PURPOSES : Rut depth of asphalt pavements is a major factor that affects the maintenance of pavements as well as the safety of drivers. The purpose of this study was to analyze the factors influencing rut depth, using data collected periodically on national highways by the pavement management system and, consequently, predict annual rut depth change, to contribute to improved asphalt pavement management. METHODS : The factors expected to influence rut depth were determined by reviewing relevant literature, and collecting the related data. Further, the correlations between the annual rut depth change and the influencing factors were analyzed. Subsequently, the annual rut depth change model was developed by performing regression analysis using age, present rut depth, and annual average maximum temperature as independent variables. RESULTS : From the sensitivity analysis of the developed model, it was found that age affected the annual rut depth change the most. Additionally, the relationship between the dependent and independent variables was statistically significant. The model developed in this study could reasonably predict the change in the rut depth of the national highway asphalt pavements. CONCLUSIONS : In summary, it was verified that the model developed in this study could be used to predict the change in the National Highway Pavement Condition Index (NHPCI), which represents comprehensive conditions of national highway pavements. Development of other models that predict changes in surface distress as well as international roughness index is required to predict the change in NHPCI, as they are the independent variables of the NHPCI prediction model.

PURPOSES : In this study, an ASR-reducing (alkali-silica reaction) cement was developed to prevent the blow-up of concrete pavements. To develop ASR-reducing cement, various amounts of ground granulated blast furnace slag (GGBFS), and fly ash (FA) were substituted with Portland cement, and the ASR reduction effect was verified through various experiments. METHODS : The physical properties of ASR-reducing cement, varying with the substitution amounts of GGBFS and FA, were verified through compressive strength tests. In addition, the ASR reduction effect was examined using accelerated mortar bar tests. Furthermore, the reasons for the ASR reduction were investigated using microstructural analysis techniques, such as XRD and TG/DTG. RESULTS : There was a difference in the compressive strength results according to the amount of GGBFS and FA substitution. In addition, the samples with GGBFS and FA exhibited relatively lower compressive strengths at 3 days, than OPC samples, but the compressive strength at 28 days was higher than that of the OPC samples. The samples with GGBFS and FA had higher compressive strength at 28 days than OPC samples, because the substituted GGBFS and FA induced pozzolanic reaction. Through XRD and TG/DTG analyses, various degrees of pozzolanic reaction occurring in the samples were examined, and a more active pozzolanic reaction occurred in the samples with FA than in the samples with GGBFS. Therefore, it appeared that the ASR reduction effect occurred because of the induced pozzolanic reaction. CONCLUSIONS : GGBFS and FA substituting Portland cement indicated an ASR reduction effect, which was owing to the pozzolanic reaction. In addition, FA indicated a greater ASR reduction effect than GGBFS, which suggested that FA induced a more active pozzolanic reaction than GGBFS.

PURPOSES : Given that large-scale repair works of expressway bridge pavements have high maintenance cost and long traffic blocking time, the thin overlay method that maintains the existing pavement is attracting attention. In this study, because the bridge thin overlay has not been introduced in Korea yet, the basic physical properties of the epoxy thin overlay, which is mainly used for the bridge thin overlay, were investigated, and the skid resistance and bond performance were analyzed. METHODS : Basic physical property tests were performed on each of the epoxy binders, aggregates, and mixtures used in epoxy thin overlay. They were also compared and reviewed against foreign standards. The epoxy binders were tested for viscosity, gel time, and thermal compatibility. The aggregates were tested in terms of water absorption, specific gravity, and gradation. The compressive and flexural strengths of the mixtures were investigated. The epoxy thin overlay has the possibility of detachment of aggregates, so the skid resistance was tested according to the paving phase. In addition, to investigate the bond performance, which is the most important performance of the epoxy thin overlay, the bond strength test was performed by varying the moisture condition and treatment condition of the existing layer surface. RESULTS : The basic physical properties of the materials used in the epoxy thin overlays satisfied foreign standards except for the gradation of aggregates. The skid resistance did not satisfy the standard when the epoxy was exposed, whereas the skid resistance did satisfy the standard when the aggregates were exposed, even after the abrasion test. The bond strength of the epoxy thin overlay satisfied the standard in all cases. The bond strength was the highest when the relative humidity of the existing layer surface was 60%. CONCLUSIONS : The materials of epoxy thin overlay that could be obtained in Korea satisfied the basic physical property standards except for aggregate gradation. Given that the aggregate gradation could be adjusted, it can be concluded that the epoxy thin overlay could be introduced in Korea. In addition, it was confirmed that the skid resistance and bond strength of the epoxy thin overlay were high enough to be used in general road conditions. It was determined that the existing layer surface should maintain an optimal relative humidity of approximately 60% because the moisture condition affects the bond strength.

PURPOSES : The purpose of this study was to investigate the performance of additives that affect internal curing in order to reduce the damage occurring in concrete pavements. METHODS : SAP was used as an additive to reduce internal curing in concrete pavements. SAP is an additive that has a very high absorption rate which prevents concrete wrappers from externally draining water. To evaluate the internal curing performance according to the ratio of SAP, we identified the number of cracks and amount of abrasion reduction. RESULTS : Plastic shrinkage and durability of a concrete mixture with added SAP were evaluated. The following results were obtained: (1) SAP showed a tendency to reduce slumps due to absorption of the concrete mixture. (2) It was possible to verify that concrete condensation did not occur during the penetration resistance test and that the initial curing did not lead to reactions within the mixture. (3) Adding more than 0.6% of SAP for dry curing resulted in greater compressive strength at all ages than OPC, with the highest compression strength of 0.9% after 56 days. (4) Regarding abrasion resistance, it was found that adding SAP was 30~50% better than adding the OPC mixture, and at 0.9% compression strength, abrasion resistance showed the best performance. (5) In the chlorine ion immersion resistance experiment, the passing charge of the OPC mixture was rated “high,” but it was rated “normal” in SAP. The results showed that the addition of SAP improved the water density of concrete due to internal curing effects, and that it showed the greatest chlorine ion penetration resistance for a compressive strength of 0.9%. (6) Regarding plastic shrinkage resistance, cracks did not occur on the surface until the end of the experiment, but the plastic shrinkage rate upon addition of SAP was relatively low compared to that of the OPC mixture. CONCLUSIONS : Recent studies have shown that internal curing techniques can be applied using SAP to prevent shrinkage due to the loss of water and to decrease the effects of hydration. If internal curing effects are expressed using SAP, it is thought that contraction due to a loss of moisture and reduction in sign language reaction can be prevented.

PURPOSES : The type and degree of structural conditions and influencing factors distributed across representative sections should be similar to those distributed across entire sections as the representative sections have been predominantly used for developing performance prediction models, which substitute entire sections of road pavement. Therefore, a logic that selects the representative sections with similar distributions of structural conditions and the influencing factors with those of entire expressway asphalt pavement sections requires development. METHODS : The logic developed in this study to select the representative sections of asphalt pavements comprised three steps. First, the data on the structural conditions of the pavement and the influencing climate conditions and pavement materials were collected and organized. Consequently, in the second step, the candidate sections were selected, with the severity of the structural conditions of the pavement distributed widely and evenly. Finally, in addition to the widely and evenly distributed pavement conditions, the representative sections with climatic conditions and pavement materials were selected. RESULTS : A total of 6,352 ordinary asphalt pavement sections and 596 composite asphalt pavement sections were selected as entire expressway asphalt pavement sections and the data were collected and organized according to the logic developed in this study. Three times the representation sections were selected as candidate sections and, finally, 85 sections were selected as representative sections. The distribution of structural conditions and influencing climate conditions and pavement materials in the representative sections were similar to those in the entire sections. In addition, the representative sections were spread evenly across the country. CONCLUSIONS : The sections presenting similar distributions of structural conditions and the influencing factors of entire expressway asphalt pavement sections could be selected in this study. Using the representative sections selected in this study, a remodeling index model will be developed for predicting the asphalt pavement sections that require large-scale repair.