The mandible character of the Lucanidae is vary by considering of developmental difference in male individual specimen. Especially, species of Genus Cyclommatus Parry, 1862 presents strong mandibular allometry. In this research, The species group which related to Cyclommatus montanellus Möllenkamp, 1904 has been evaluated for the first time in this research with inner teeth composition and positioning to establish clear taxonomic key to each species.

Piezoelectric harvester for road power generation was installed on test roads owned by Korea Highway Corporation. 24 harvesters were installed on the concrete pavement and the remaining 12 harvesters were installed on the asphalt pavement. After installation, power generation performance and environmental tests were carried out with three types of vehicles: compact / passenger cars / trucks. The running speed of the vehicle was 30 km/h, 60km/h, 90 km/h. The test results show that the larger the weight of the vehicle, the higher the power generation, the concrete road than the asphalt road, and the exposed type rather than the buried type. The generation amount according to the depth of buried was at least 2.2 times at the depth of 1cm than 5cm depth. When the delegator lighting test was performed using 12 harvesters, it was possible to light up more than 20 seconds in one vehicle due to the improvement of the charging circuit. In addition, the wireless communication module driving test enabled temperature sensing and data transmission for 25 seconds. In addition, there was no breakage of the pavement when driving more than 180 times, and the generation amount was maintained more than 90%. However, Test for the durability of the pavement and the self-durability of the harvester is required more than 180 times of vehicle driving conditions and required more than minimum of 6-12 months of long-term monitoring.

Among the 8,700 in-service bridges in national highway, the steel bridges cover the 1600 sites and make up approximately the 20 percentage of the total amounts. Due to recent rapid increase both in traffic volume and in frequency of overloaded vehicles, the need for re-evaluating the fatigue life of the steel bridges is increasing. However, the existing fatigue life assessment method are too complicate and difficult to apply to field directly. To improve such deficiency of the existing fatigue life assessment procedures, this study reviews the fatigue life assessment methods in Eurocode and then proposes an easier and simpler fatigue life assessment procedure that could evaluate the remaining fatigue life of the steel bridges using traffic data collected from a high-speed weigh-in-motion system installed in the national highway network. The Proposed fatigue life evaluation method is as follows; 1. Calculation of fatigue resistance 𝛾𝑀f and fatigue strength Δ𝜎𝑐 used in design, 2. Calculation of partial safety factor 𝛾𝐹f for equivalent stress range, 3. Calculation of stress range Δ𝜎𝐸2 using influence line, 4. Calculation of damage equivalent factor λ, 5. Review of Fatigue state and evaluation of fatigue life. The Proposed method can omit the existing complicated and repetitive calculation. Therefore, proposed method can estimate the fatigue damage and the theoretical fatigue life simply by comparing with the existing method.

The recent increase in truck traffic volume and overloading frequency causes a growing need to re-evaluation of fatigue life of steel bridges. However, the traditional fatigue analysis method, that is cumulative damage method(CDM), has limitation to apply to a number of bridges because the required calculation steps are very cumbersome and complicated. This study investigates the feasibility and applicability of proposed simple fatigue evaluation method based on the equivalent damage method (EDM) in Eurocode to estimate the remaining fatigue life for a highway bridge. The Proposed fatigue life evaluation method is as follows; 1. Calculation of fatigue resistance 𝛾𝑀f and fatigue strength Δ𝜎𝑐 used in design, 2. Calculation of partial safety factor 𝛾𝐹f for equivalent stress range, 3. Calculation of stress range Δ𝜎𝐸2 using influence line, 4. Calculation of damage equivalent factor λ, 5. Review of Fatigue state and evaluation of fatigue life. The specifications of the target bridge are as follows; Location : Gyeongbu Expressway, Design Life : 100yr, Construction year : 2006, Total length : 341m, Type of superstructure : continuous steel box girder. The resulting remaining fatigue life estimated by both EDM and CDM have been compared. Remaining fatigue life of target bridge in 2016 was calculated 365yr(EDM using WIM data in 2014), 334yr(CDM using strain gauge data in 2012 and reflecting 2% annual traffic volume increase, Gil and Kang(2012)). As a result of comparison, The remaining fatigue life using proposed method(EDM) was evaluated about 10% higher than the CDM. This result, because traffic volume increase had not reflected when calculation of remaining fatigue life using EDM. Proposed method(EDM) can evaluate remaining fatigue life more easily and simply than CDM.

Biochar obtained from the thermal conversion of biomass has high potential as a substitute material for activated carbon and other carbon-based materials because it is economical, environmentally friendly, and carbon-neutral. The physicochemical properties of biochar can also be controlled by a range of activation methods such as physical, chemical, and hydrothermal treatments. Activated biochar can be used as a catalyst for the catalytic pyrolysis of a biomass and as an absorbent for the removal of heavy metal ions and atmospheric pollutants. The applications of biochar are also expanding not only as a key component in producing energy storage materials, such as supercapacitors, lithium ion batteries, and fuel cells, but also in carbon capture and storage. This paper reviews the recent progress on the activation of biochar and its diverse present and future applications.

Hierarchically porous, chemically activated carbon materials are readily derived from biomass using hydrothermal carbonization (HTC) and chemical activation processes. In this study, empty fruit bunches (EFB) were chosen as the carbon source due to their sustainability, high lignin-content, abundance, and low cost. The lignin content in the EFB was condensed and carbonized into a bulk non-porous solid via the HTC process, and then transformed into a hierarchical porous structure consisting of macro- and micropores by chemical activation. As confirmed by various characterization results, the optimum activation temperature for supercapacitor applications was determined to be 700°C. The enhanced capacitive performance is attributed to the textural property of the extremely high specific surface area of 2861.4 m2 g–1. The prepared material exhibited hierarchical porosity and surface features with oxygen functionalities, such as carboxyl and hydroxyl groups, suitable for pseudocapacitance. Finally, the as-optimized nanoporous carbons exhibited remarkable capacitive performance, with a specific capacitance of 402.3 F g–1 at 0.5 A g–1, a good rate capability of 79.8% at current densities from 0.5 A g–1 to 10 A g–1, and excellent life cycle behavior of 10,000 cycles with 96.5% capacitance retention at 20 A g–1.

Ginger is generally consumed as food or medicine in Korea and mostly imported from China. During quarantine inspection,genus of nematodes, Meloidogyne spp. and Pratylenchus spp., are mainly detected and regulated under the procedure ofquarantine in Korea. We tested the susceptibility and mortality rates of Meloidogyne spp., which are infected in ginger,against a fumigant, Ethanedinitrile (EDN). Juveniles of the nematode showed 100 % mortality against EDN at 2.5 mg/Lfor 2 h at 13°C, meanwhile, egg mass showed 0 % hatching at 5 mg/L for 2 h at 13°C. A concentration × time product(CTP) was determined as 7.24 ghm-3. Under the 35% filling rate of ginger in cold chamber, 100% mortality was observedin both juveniles and eggs at 50 mg/L for 2 h at 13°C. At that condition, CTP was determined as 14.12 ghm-3. Basedon this study, EDN fumigation will be effectively apply to control of nematodes.

Wood pellets are used by Biomass-solid refuse fuel (Bio-SRF) has been imported from many East-Asia countries especially,Vietnam in Korea. Wood pellets are made through grind and high-pressure process shows different physical characterizationlike high methyl bromide (MB) absorption unlike other wood materials. Furthermore, detected pests in wood pellets havesimilarity with detected pests in stored grain. In this study, we analyzed susceptibility on pupa and adult stages of redflour beetle, Tribolium castaneum in wood pellets against mixture of MB and phosphine (PH3). Mixture treatment ofMB and PH3 was more effective than single MB treatment compare with control. Pupal stage showed more tolerant thanadult stage on each fumigant and 100% mortality was determined at 27 mg/L of MB only at 20°C. However, PH3 increasedMB toxicity on pupae that 100% mortality was observed at 100:1 ratio of MB (5 mg/L) and PH3 (0.05 mg/L) at 20°C.Based on this study, mixture treatment of different type of fumigant will be applied to control of quarantine pests.

Auricularia polytricha has strong decomposition ability on wood fiber and a wide range of temperature adaptation as mid-high temperature mushroom. In addition, Auricularia polytricha does not require light in the mycelial growth period, but it is cultivated in the field because the light promotes the differentiation of fruiting bodies and affects the pigment formation. This study was conducted to investigate the possibility of the cultivation of Auricularia polytricha (Mont.) Sacc. "Geoni" which was bred at Jeonnam Agricultural Research Institute in 2012 at a simple-typed PE film mushroom house, and to compare the quality characteristics of the Auricularia polytricha (Mont.) Sacc. "Geoni" cultivated at air-conditioned mushroom house. Auricularia polytricha (Mont.) Sacc. "Geoni" was cultivated with sawdust-based media (0.9 kg) every 3 days from June 15 to July 13 at air-conditioned mushroom house and PE film mushroom house, and harvested until July 26th. The temperature and the humidity of the air-conditioned mushroom house was maintained at 23°C and 90-9 %. The Irrigation was conducted 1 time per day and 2 to 3 times per day at air-conditioned mushroom house and PE film mushroom house respectively. The harvesting period were the same for each treatment. The fruiting body was 6.0 ㎝ and 5.1 ㎝ in major axis and 4.6 ㎝ and 4.0 ㎝ in minor axis at PE film mushroom house and air-conditioned mushroom house respectively, as a result the size of the fruiting body grown at PE film mushroom house tended to be larger. The thickness of fruiting body was 0.85㎜ and 1.24㎜ at PE film mushroom house and air-conditioned mushroom house respectively. These results are considered to be due to the difference in the humidity control conditions between each treatment. The number of fruiting bodies per bag was 4.3 at PE film mushroom house and more tendency than 3.7 at air-conditioned mushroom house. The springiness of the fruiting body was 1.23 ± 0.21 and 1.01 ± 0.17. the chewiness was 620 ± 89 and 507 ± 128, and the resilience was 0.49 ± 0.03 and 0.35 ± 0.07 at PE film mushroom house and air-conditioned mushroom house respectively. As a whole, it was judged that the physical properties of the fruiting body grown at PE film mushroom house were excellent. Also, when comparing the chromaticity of fruiting body, L(lightness)-a(red color)-b(yellow color) value was 30-5.5-3.9 and 39-6.5-7.5 at PE film mushroom house and air-conditioned mushroom house respectively. The yields did not show differentiated tendency by cultivation time. However, the weight of fruiting body per bag was 308g and 252g at PE film mushroom house and air-conditioned mushroom house respectively. Therefore, according to these result, Auricularia polytricha (Mont.) Sacc. "Geoni" was judged to be a suitable cultivar at PE film mushroom house for summer.

An intensive analysis was conducted of the maternal lineages of the Jeju native pigs (JNPs). A total of 100 mtDNA sequences from Asian wild boars (AWB), European wild boars (EWB), Asian domestic pigs (ADP), European domestic pigs (EDP), and JNPs were used for the phylogeny and network analyses. Two distinct JNP groups were found JNPA and JNPE in the Asian and European cluster. The maternal lineage of JNPE was the closest to that of EWB and a clear haplogroup sharing an identical haplotype (hap16) among 15 individuals of JNPE and 2 individuals of EWB was identified. However, except for hap18, no EDP shared any identical haplotypes with JNPE, suggesting that no obvious maternal contribution of EDP has occurred in JNPE in recent years. The possible existence of an additional and unknown path of maternal lineage from EDP into JNPE could therefore be postulated, in addition to those from AWB and ADP into the JNPA groups. Thus, JNPE appeared to have a pure maternal lineage that had no recent contact with EDP, and both the JNPA groups and JNPE are pure Jeju native pigs.

Wolfiporia cocos is a well-known traditional medicine in China, Japan, Korea, and other Asian countries owing to its numerous therapeutic properties. With the aim to determine the morphology and genetic characteristics of W. cocosten strains of W. cocos were cultivated in vitro, and subsequently, rapid amplification of polymorphic DNA was performed. To the best of our knowledge, this is the first study to examine the morphology of fruit bodies of W. cocos in Korea. W. cocos were cultured on PDA agar at different temperatures (12, 16, 20, 24, and 28oC) under 12-hour light (600 Lux) / 12-hour dark photoperiod condition for 1 month. Appearance of fruit body was the highest at 28°C condition in all the strains investigated. Honeycomb-like structure on sclerotia was observed in Andong 01, Andong 02, Andong 03, KFRI 1104, KFRI 1105, KFRI 1106, KFRI 1107, KFRI 1108, and ASI 13007 strains of . The KFRI 1103 strain formed cosmos petal-like structure on sclerotia. The average size of basidiospores was recorded as 7.55 μm in height and 3.35 μ in width.

Vegetable seed oils (VSOs) have been extracted and used not only as ingredients in food and as sources of dietary lipids, but also as sources of nutraceuticals used to overcome the various oxidative stresses that contribute to the development of diseases, including cancer and other chronic conditions. The chemical compositions and oxidative stabilities of various VSOs were therefore investigated; samples were stored for 35 d, with each oil having been tested under O2 exposure, sealed from O2 exposure and sealed from O2 exposure while containing O2 scavengers. Oxidative stability was evaluated by peroxide value (POV), p-anisidine value (p-AnV), iodine value (IV), and thiobarbituric acid (TBA) value. Perilla seed and flaxseed oil were mostly composed of linolenic acid (45.5% and 59.7%, respectively), whereas pine seed oil was mostly composed of linoleic acid (48.3%). Meanwhile, camellia seed and olive oils contained 80% oleic acid, which correlated strongly with oxidative stability. The POV, p-AnV, and TBA values were the highest under O2 exposure, and the lowest in the presence of O2 scavengers. These results indicate that VOS oxidative stability depends not only on storage conditions, but on unsaturated fatty acid profiles as well.

경주 방사성폐기물 처분시설은 향후 80만 포장물을 처분할 계획이며 다양한 처분방식 및 관리형태를 가진 복합계가 될 것 이다. 본 논문에서는 전체부지 처분용량(80만 포장물) 처분시설의 단계별 개발에 따른 영향을 평가하기 위하여 처분시설 종 합개발계획(안)에 따른 예비안전성평가를 수행하였다. 각 시나리오에 대한 안전성평가결과 처분시설의 성능목표치를 만족 하였다. 다만, 전체처분시설의 안전성 평가결과에 중준위 방사성폐기물로 인하여 1단계 동굴 처분시설이 가장 크게 영향을 미치므로 처분시설의 안전성 향상을 위하여 처분방사능량제한 설정 등 관리방안이 필요하다. Safety Case 단계별 구축을 통 하여 중·저준위 방사성폐기물 처분시설 종합개발 과정에서 인지된 불확실성을 저감하여 안전성을 증진 시킬 수 있을 것으 로 판단된다.