Line capacity calculation has been used to determine optimum efficiency and safe train service for train scheduling plan and investment priority order throughout detecting bottleneck section. Because of some problems of Yamagisi and UIC methods for line capacity calculation, developing of the method of line capacity caculation and evaluation for the Korea circumstance is important. This paper deals with the reliability improvement on the integrated system of TPS(Train Performance Simulator), PES(Parameter Evaluation Simulator), LCS(Line Capacity Simulator) and simulation and sensitivity analysis for line capacity.

This paper is to propose various safety design models of tolerance specifications with different consumer requirements. In these models, tolerance specifications can be jointly determined by considering all the stochastic, economic, robust and engineering safety design factors with various characteristics of interest. In this paper, the proposed models are easily formulated for design engineers.

There are very large differences on the standards of gross weight and single axle weight for commercial motor vehicles between international and Korean standards. Short Wheelbase Truck are produced and run only in Korea. It has very serious effects on the durabilities of bridges and roads and makes logistic competitive power fall back and overconsuming energy. This paper deals with a comparative study of the international standards with Korean, grasps the drawbacks and makes up the suggestions to strengthen the logistic competitive power of Korea and reduce the maintenance cost for the roads and the consumption of energy.

A study is for the approach that we could reduce the logistics costs through uprising the efficiency, complying to the demand in time, stock management based on the general production plan in the point of SCM. We will take following steps to get the goal. First, we will overview the physical distribution expenses annually. Second, will find the main cause of optimal load loss by improper container and lack of delivery flexibility to the demand. Third, the goal will be inferred through the fast information share based on organic relationship, the establishment of general production plan, the improvement of stock management plan. By way of this process, it can be accomplished expense reduction as well as flexible establishment of the reduction of worker's load.

Many countries of the world is driving forward development of large-scale hub port. They are now pushing ahead with setting up of effective marketing strategies to survive in keen competitions of the 21st century port industry. The port is of ever increasing importance for the bridge connecting sea and road transportation in handling international cargoes. The port, differently from general working places, is a closed area required for security, customs, and quarantine procedures. The loading and unloading is being done differently by ports, cargoes, and ships. To do loading and unloading, a lot of equipment and different types of labor are required, which flow is complicated and safe management is essential. As above mentioned the port is very unique and very deteriorated working place in its working environment. The purpose of this study is to propose ways to reduce and prevent from port accidents. As first step to do this, we have collected 923 accidents happened at Incheon Port during the period of 1994 to 2003. We have thoroughly analyzed characteristics, harmfulness, and risk of the loading/unloading they have done, as well as the accident frequency and relationship between the accidents. As second step to further analyze, We have employed DMAIC technology, an advanced process of 6 sigma presently in spotlight as the best program for management innovation. This analysis results in recognition of important accident characteristics, causes and effects analysis, critical causes of accident, and suggestions to decrease accidents.

A study is for the approach that we could reduce the logistics costs through uprising the efficiency, complying to the demand in time, stock management based on the general production plan in the point of SCM. We will take following steps to get the goal. First, we will overview the physical distribution expenses annually. Second, will find the main cause of optimal load loss by improper container and lack of delivery flexibility to the demand. Third, the goal will be inferred through the fast information share based on organic relationship, the establishment of general production plan, the improvement of stock management plan. By way of this process, it can be accomplished expense reduction as well as flexible establishment of the reduction of worker's load.

Many countries of the world is driving forward development of large-scale hub port. They are now pushing ahead with setting up of effective marketing strategies to survive in keen competitions of the 21st century port industry. The port is of ever increasing importance for the bridge connecting sea and road transportation in handling international cargoes. The port, differently from general working places, is a closed area required for security, customs, and quarantine procedures. The loading and unloading is being done differently by ports, cargoes, and ships. To do loading and unloading, a lot of equipment and different types of labor are required, which flow is complicated and safe management is essential. As above mentioned the port is very unique and very deteriorated working place in its working environment. The purpose of this study is to propose ways to reduce and prevent from port accidents. As first step to do this, we have collected 923 accidents happened at Incheon Port during the period of 1994 to 2003. We have thoroughly analyzed characteristics, harmfulness, and risk of the loading/unloading they have done, as well as the accident frequency and relationship between the accidents. As second step to further analyze, We have employed DMAIC technology, an advanced process of 6 sigma presently in spotlight as the best program for management innovation. This analysis results in recognition of important accident characteristics, causes and effects analysis, critical causes of accident, and suggestions to decrease accidents.

The purpose of this study is to develop S/W of the web-based collaborative warehouse management system using RFID(Radio Frequency Identification). This S/W System supports the realtime inventory management and collaborative operations of relational companies in SCM. We look for benefits-reduce inventory levels, maxmize use of warehouse space, decrease the logistic cost, and increase competitive power of company, using this S/W

There are very large differences on the standards of gross weight and single axle weight for commercial motor vehicles between international and Korean standards. Short Wheelbase Truck are produced and run only in Korea. It has very serious effects on the durabilities of bridges and roads and makes logistic competitive power fall back and overconsuming energy. This paper deals with a comparative study of the international standards with Korean, grasps the drawbacks and makes up the suggestions to strengthen the logistic competitive power of Korea and reduce the maintenance cost for the roads and the consumption of energy.

This study deals with the procedure of safety improvement, productivity increase ,and tact-time reduction through setting up the system about preventive maintenance. Actually, it is hard to establish and carry out preventive maintenance, even though we recognize the importance of the system concerning time, cost, labor, and so forth. In this study in the viewpoint of cost we are for achieving maximum efficiency by change and reduction of planning process adapted to the special work group. At first we briefly will mention the kind ,the necessity ,and the concept of preventive maintenance ,and then divide the equipment used in the assembly line into the two whether it is necessary or not by way of estimating the breakdown loss ,comparing with general establishment of preventive maintenance and modifying it to the case. At the second step we will establish the operation system of plan management related to production and quality in the special case. Check period and category will be set by dividing the assembly equipment into LCL and Focus in the third step. The forth step will contain the operation procedure in detail. And then we must make check and repair record periodically. Finally, on the basis of the record the selection of checking of significance will be conducted. This results in safety improvement, tact time reduction, and productivity improvement.

This development has tried to scheme out the convenience for users to use the 3D modeling solution which is developed from the existing programs. The extended 3D modeling solution, to be developed through the use of the API which is provided and Microsoft Access, database is able to reuse the parts, subassemblies of parts, and assemblies. A methodology exhibits the possibility to use a Spinfire Professional Spinfire Reader program. The web evaluation system, which is used to connected with the Internet explorer and to construct a web service, will repeat the evaluations of the company staffs and customers about the new products which the company have designed. The furniture manufacturing company will adopt the 3D modelling solution in modelling the new products and go through the web evaluation system to collect dissatisfied facts of the customers or the company staffs against the new product. Finally, it will contribute to the enormous benefit creation of the enterprise.

This study develops a improved gate assignment algorithm and decision support system using its algorithm to extract a assignment result minimizing a walking distance of passengers in airport and maximizing the utilization rate of avaliable gates in domestic airports. By operation support system, it may contribute greatly in efficient enlargement of airport operation and increase the airport reliability through quickly coping with takeoff and landing delay of flight due to weather change, preservation and repair of gate, etc. Also, passengers who use airport terminal can minimize time and walking distance for departure, arrival, and transit, and it may greatly reduce the additional operation cost for common gates through maximizing the utilization rate for exclusive usage gates for airplanes which use gates.

This study develops a improved gate assignment algorithm and decision support system using its algorithm to extract a assignment result minimizing a walking distance of passengers in airport and maximizing the utilization rate of avaliable gates in domestic airports. By operation support system, it may contribute greatly in efficient enlargement of airport operation and increase the airport reliability through quickly coping with takeoff and landing delay of flight due to weather change, preservation and repair of gate, etc. Also, passengers who use airport terminal can minimize time and walking distance for departure, arrival, and transit, and it may greatly reduce the additional operation cost for common gates through maximizing the utilization rate for exclusive usage gates for airplanes which use gates.

A purpose of this research is building a Parameter Evaluation Simulation(PES) program which is present proper parameter value to calculate line capacity. This research performs a detailed simulation and a analysis of it using PES and it is developed on the basis of Line Capacity Simulation model. Chosen simulation sectors are that happened a big change of a line capacity because of joining a high speed train(KTX). Moreover this research performs a sensitivity analysis when basic data are changed.

This study deals with the procedure of safety improvement, productivity increase, and tact-time reduction through setting up the system about preventive maintenance. Actually, it is hard to establish and carry out preventive maintenance, even though we recognize the importance of the system concerning time, cost, labor, and so forth. In this study in the viewpoint of cost we are for achieving maximum efficiency by change and reduction of planning process adapted to the special work group. At first we briefly will mention the kind, the necessity, and the concept of preventive maintenance, and then divide the equipment used in the assembly line into the two whether it is necessary or not by way of estimating the breakdown loss, comparing with general establishment of preventive maintenance and modifying it to the case. At the second step we will establish the operation system of plan management related to production and quality in the special case. Check period and category will be set by dividing the assembly equipment into LCL and Focus in the third step. The forth step will contain the operation procedure in detail. And then we must make check and repair record periodically. Finally, on the basis of the record the selection of checking of significance will be conducted. This results in safety improvement, tact time reduction, and productivity improvement.

Port, one of nation's key infrastructures, is a point of road and sea transports meeting. As a key base of inter-modal transportation systems, the port is of ever increasing importance for realizing nation's vision of making Korea as an economic and logistics hub in the Northeast Asia. At present, Korean ports handle 99.7% of gross trade volumes in Korea, which requires considerable attention on its safety issues. However, due to the critical characteristics of the port and insufficient attention paid to it, the port industry meets more disasters compared to other industries. Therefore, this paper tries to analyze the disasters happened at the port to have better understanding on its reasons, further to use as learned lessons to prevent from potential disasters that may arise at the port.

가구 제품 설계 및 디자인의 과정이 고도로 높은 기술력을 바탕으로 이루어지고 있으며, 국내의 가구 기업체도 우수한 기술력과 높은 품질로 경쟁력을 키우며 다양한 고객의 요구에 대응하여 고객만족을 꾀하여야 한다. 이의 기반이 되는 제품의 품질과 사양은 설계에서 시작되는데 아직 국내의 많은 가구기업들은 설계 및 제작 단계에서 많은 시간과 비용을 낭비하고 있다. 3D Modeling Solution은 설계오류가 적으며 시각적인 설계를 할 수 있어 최소의 인력으로 제품을 설계할 수 있는 장점이 있지만 너무 많은 기능으로 인해 사용자가 쉽게 적용하고 사용하기 어려운 단점을 가지고 있다. 본 연구에서는 Autodesk사의 Inventor와 Microsoft Visual Basic으로 Inventor에서 제공하고 있는 API함수를 이용하여 조립자동화를 위한 조립조건 생성, 조립자동화, 부품 재질변경, 수동조립 그리고 부품의 DB화를 구현하고 Add-ln 기능과 미리보기 기능을 구현하였다. 그리고 Actify사의 SpinFire Professional 프로그램을 이용해서 웹에서 모델링된 가구 부품이나 제품을 볼 수 있게 하였다.