본 논문은 콘크리트 배합 방식(NMA, TSMA1, TSMA2)에 따른 순환 굵은골재 치환량에 따른 콘크리트의 기계적 성능을 비교 평가 하였다. 실험은 순환 굵은골재를 0%, 50%, 100%로 3수준으로 콘크리트의 배합 방식에 따라 실험을 진행하였다. 굳지 않은 콘크리트에서는 공기량, 슬럼프, 단위용적질량 실험을 진행하였으며, 경화 콘크리트에서는 압축강도 및 휨강도 시험을 진행하였다. 본 연구의 실험결과 NMA 방식과 비교하여 TSMA 방식에서 강도 저하가 나타나고 있음을 확인할 수 있었다. 하지만, 이는 순환 굵은골재가 다량 치환됨에 따른 것으로 사료된다. 순환 굵은골재가 다량 치환됨에 따라 슬럼프 증진, 공기량 증진, 강도 저하가 나타남을 확인하였다.

Chloride attack is one of the most critical deterioration due to rapid corrosion initiation and propagation which can cause structural safety problem. Extended service life through repairing is very important for determination of maintenance strategy. Conventionally adopted models for estimation of LCC (Life Cycle Cost) have shown step-shaped elevation of cost, however the extension of service life is much affected by quality of construction and repairing materials, which means engineering uncertainties in residual service life. In the paper, RC (Reinforced Concrete) column with three different mix proportions exposed to chloride attack are considered, and repairing numbers with related costs are evaluated through probabilistic technique for maintenance. When calculating repair frequency for intended service life through probabilistic model, the required repair frequency is evaluated to be 6.71 times for OPC, 4.09 times for SG30, and 2.95 times for SG 50, respectively. The probabilistic model for repairing cost is evaluated to be effective for reducing the repair frequency reasonably with changing the intended service life and design parameters.

The joints in this construction are formed through the bonding shear evaluation method during the placement of ultra-high-performance concrete (UHPC). The evaluation items include push-off tests for homogeneous UHPC + UHPC. The experimental samples comprised a monolithic placement as the baseline, two levels for the separated placement according to the compression strength of concrete, and five levels for the interface treatment. The bonding shear performance for the homogeneous UHPC + UHPC construction linearly increased with the width and depth of the grooves used for the interface treatment. The increase in the number of grooves and their cross-sectional areas only slightly influenced the bonding shear performance. The optimal interface treatment method for the homogeneous UHPC + UHPC construction grooves was at least 30 mm.

The method of lowering the diffusion coefficient of concrete are widely used by mixing blast furnace slag(BFS) and fly ash(FA) in order to prevent the steel corrosion. In this study, the NaCl solution was supplied and the potential of the reinforced steel was monitored to measure the critical chloride contents of the reinforced concrete according to the type of concrete. In case of using BFS and FA, it showed that the corrosion of the steel was progressed rapidly, which is considered to be related to the decrease of the pH of the concrete.

In this study, the expandable shale collected from the same area in Korea is fired to confirm the foamability. The firing uses an electric furnace capable of firing up to 1600 ℃. The shale was classified into three types according to its constituent and apparent characteristics, and each component was analyzed by XRD analysis method. The shale was fired considering the firing temperature and the residence time. As a result of firing, it was found that the firing temperature was different by more than 100 degrees and it was confirmed that the foaming property was increased with increasing temperature

Prediction of the compressive strength of the maturity method has been studied by several researchers and has been applied to the construction of concrete structures. In order to apply the maturity method, which is a function related to temperature and time, it is important to measure the accurate temperature inside the concrete during the curing period. The purpose of this study is to verify the performance by analyzing sensitivity, measurement and transmission accuracy by exposing wireless embedded sensor to various curing environment.

염해에 따라 발생하는 보수시기와 보수로 유지되는 내구수명은 보수비용 평가에 매우 중요한 요소이다. 일반적으로 사용하는 결정 론적 보수비용 평가는 사용기간의 연장에 따라 계단식으로 증가하게 되며, 보수로 인해 변동되는 내구수명의 변화를 고려하지 못한다. 본 연구 에서는 확률론적인 보수시기 및 비용을 평가하기 위해, 염해에 노출된 콘크리트 교각을 선정하였다. 두 가지 배합과 염화물에 노출된 외부 환 경조건을 고려하여 염화물 거동을 평가하였으며, 도출된 내구수명과 수명에 대한 확률변수를 변화시키면서 보수시기 및 비용 변화를 분석하 였다. 변동계수의 변화에 따른 보수회수는 큰 차이가 발생하지 않았으나, 초기의 내구수명 연장이 구조물의 보수시기 및 비용에 큰 영향을 미 치고 있었다. 또한 확률론적 보수비용 산정 모델은 결정론적 모델과 다르게 연속적인 보수비용이 평가되므로 목표내구수명에 따라 보수회수 를 감소시킬 수 있는 효과적인 기법임을 규명되었다.

In this paper, it is described for the technology trends of Durability Health Monitoring (DHM) using sensors and monitoring Methods. Specially, the chloride ion penetration sensor, carbonation depth sensor, corrosion sensors for embeded rebar and wireless sensor monitoring system is described in order to enhance the durability of buildings and infrastructures.

This study investigated the properties of lightweight foamed concrete by using surfactant and synthetic foaming agent, lightweight aggregate. The effects of foaming agent types and replacing ratio of lightweight aggregate on the compressive strength, density and pore structure of the concrete were investigated. This study showed the improvement of important properties of lightweight foamed concrete. Lower pore distribution and correspondingly higher compressive strength values were reached. Also, synthetic foaming agent had more positive effect on the strength of foamed concrete.

The conventional method for estimating compressive strength of concrete has been suggested by considering only 1 to 3 influential factors. In this study, seven influential mixture factors (Water-Cement Ratio, Water, Cement, Fly ash, Blast furnace slag, Curing temperature, and humidity) of papers opened for 10 years were collected at three conferences in order to know tendency of data. The purpose of this paper is to estimate compressive strength more accurately by applying it to algorithm of the Deep learning.

Recently, Advanced water treatment facilities with Ozone are being introduced domestically. However, waterproofing/corrosion prevention construction method of concrete structure for existing advanced water treatment makes waterproofing/corrosion prevention materials and concrete deteriorated because of strong oxidation of ozone. Therefore, in this study, It was evaluated in Permeability Evaluation of metal spraying coating.

In this study, flexural and tensile properties of pre-cast UHPC deck joints with surface treatment applied to fields were evaluated. It showed that all specimen set experimental variables satisfied sufficient resisting load efficiency and crack standard.

In this study, we analyzed the effect of heating curing on apartment construction in clod weather frame construction. The temperature was measured using a temperature sensor in winter and in non-winter season, the temperayure difference in the winter concrete temperature history was more than 10 degrees.

In this study, Corrosion behavior in mortar was observed by the passage of time by using EIS method. As a result of EIS experiment, equivalent circuit and changes of Impedance parameter could be observed. In addition, it was confirmed that impedance of rebar in concrete and corrosion rate according to the amount of NaCl and LiNO2 were different.

본 연구에서는 저온환경에서 콘크리트 동해를 방지하기 위해 생석회의 화학반응을 활용한 발열시트 및 단열재를 사용하여 제작한 거푸집 특성을 실험을 통해 평가하였다. -10°C 정온조건에서 거푸집 실험 결과, 발열시트가 부착된 거푸집의 경우 발열시트 내부 생석회의 발 열로 인해 타설 초기에 일반거푸집에 비해 10°C이상 높은 온도이력을 보여주었고 단열재를 부착한 거푸집의 경우 콘크리트 수화열을 보존하 여 지속적으로 높은 온도를 유지하는 특징을 나타냈다. 아이소핑크와 발열시트를 부착한 거푸집과 진공단열재를 붙인 거푸집이 압축강도나 적산온도에서 가장 높은 값을 가졌다. 압축강도 측정시 진공단열재 및 아이소핑크와 발열시트를 부착한 거푸집이 재령 3일에서 약 5 MPa로 가 장 높게 측정되었다. 몽골 현지 외기온도에서도 실험을 하였는데 앞선 결과와 마찬가지로 발열시트, 단열재를 함께 붙인 거푸집이 48시간 동안 25°C 이상으로 가장 높은 온도이력를 나타내었다. 따라서 거푸집에 발열시트 및 단열재 부착을 함으로써 발열 및 단열효과로 인해 저온환경에 서 콘크리트 강도발현에 도움을 주는 것을 확인할 수 있었다.

본 논문은 전기로 산화슬래그 골재를 사용하여 콘크리트를 제작하여 물리적 성능을 평가하였다. 실험은 전기로 산화슬래그 골재를 치환하여(잔골재-굵은골재) 0%-0%, 0%-100%, 50%-100%, 100%-100%으로 각 4수준으로 일반강도영역 W/C 45%와 고강도영역인 W/C 30% 의 2수준으로 제작하여 진행하였다. 굳지 않은 콘크리트에서는 공기량, 플로우 및 슬럼프, 단위용적질량 실험을 진행하였으며, 경화 콘크리트 에서는 압축강도 및 휨강도, 단위용적질량 실험을 통하여 물리적 특성을 검토하였다. 본 연구의 실험결과 전기로 산화슬래그의 혼입량이 증가 함에 따라 콘크리트의 강도 증진 효과가 나타났으며, 이는 전기로 산화슬래그 골재 내에 β-C2S로 인하여 골재 내외부에서 강도 증진 효과를 발 휘한 것으로 사료된다.

This study investigated the properties of foamed concrete by using surfactant foaming agent and synthetic foaming agent. The effects of foaming agent types on the compressive strength, density and pore structure of the concrete were investigated. The samples were assessed by XRD analysis and simultaneous SEM was used to study their pore distribution. This study showed the improvement of important properties of foamed concrete. Lower pore distribution and correspondingly higher compressive strength values were reached. Also, synthetic foaming agent had more positive effect on the strength of foamed concrete.

As the importance of maintenance of reinforced concrete structures spreads, interest in the durability of structures is increasing. Among them, carbonation of concrete is one of the main deterioration factors of reinforced concrete structures. For quantitative evaluation of carbonation, many researchers are predicting carbonation considering water-cement ratio and environmental requirements. In this study, we studied the parameters based on the concrete made of ordinary Portland cement in the existing experimental data. The depth of carbonation deduced from the learning is applied to the carbonation by applying the deep learning.

Recently, self-healing concrete has been researched as maintenance and repair of concrete structures are important challenges we face. This paper focused on possibility of ion exchange resin as a novelty material directly and actively controlling harmful ions of concrete, whereas most self-healing concrete researches have been focused on methods to automatically filling and repairing internal crack of concrete. Because equilibrium properties between ion exchange resin and harmful ion is important before design of cement mixing proportion, it was conducted to remove chloride or sulfate in saturated Ca(OH)2 solutions containing NaCl or Na2SO4. The removal performance was analyzed using kinetic equation and isothermal equation. Consequently, the removal properties of anion exchange resin were relatively more dependent on pseudo second reaction equation and Langmuir equation than pseudo first reaction equation and Freundlich equation. And it was concluded that each chloride and sulfate can be removed to the maximum 1068 ppm and 1314 ppm.

As the amount of slag generated annually increases, attempts to recycle slag as high value products are underway in order to develop an efficient resource recycling industry based on slag and derive economic benefits as well. However, the application of electric arc furnace (EOS) slag as construction material is practically limited because of the unstable substances included in it, such as free CaO.(EOS contains a small amount of free CaO, but several limitations still exist. Slag is stored for more than 3 months depending on the quantity of slag, which leads to additional economic loss. In this study, the amount of free CaO present in EOS is quantitatively evaluated to examine its qualities as a potential construction material and verify its application as concrete material. The quantitative analysis of free CaO present in EOS is performed using ethylene glycol. The free CaO contents of EOS samples were found to be below 0.5%. This satisfies the criteria specified in KS F 4571, which states that the CaO content should be below 40% and CaO/SiO2 ratio should be below 2.0. In addition, it was confirmed that free CaO content difference appears to be dependent on the aging period and storage position.