We investigate two abnormal CME-Storm pairs that occurred on 2014 September 10 - 12 and 2015 March 15 - 17, respectively. The first one was a moderate geomagnetic storm (Dstmin  -75 nT) driven by the X1.6 high speed flare-associated CME (1267 km s−1) in AR 12158 (N14E02) near solar disk center. The other was a very intense geomagnetic storm (Dstmin  -223 nT) caused by a CME with moderate speed (719 km s−1) and associated with a filament eruption accompanied by a weak flare (C9.1) in AR 12297 (S17W38). Both CMEs have large direction parameters facing the Earth and southward magnetic field orientation in their solar source region. In this study, we inspect the structure of Interplanetary Flux Ropes (IFRs) at the Earth estimated by using the torus fitting technique assuming self-similar expansion. As results, we find that the moderate storm on 2014 September 12 was caused by small-scale southward magnetic fields in the sheath region ahead of the IFR. The Earth traversed the portion of the IFR where only the northward fields are observed. Meanwhile, in case of the 2015 March 17 storm, our IFR analysis revealed that the Earth passed the very portion where only the southward magnetic fields are observed throughout the passage. The resultant southward magnetic field with long- duration is the main cause of the intense storm. We suggest that 3D magnetic field geometry of an IFR at the IFR-Earth encounter is important and the strength of a geomagnetic storm is strongly affected by the relative location of the Earth with respect to the IFR structure.

This research focused on Road Bike synchronized with the virtual reality software. To clarify the effectiveness of exercise using a indoor Road Bike synchronized with the virtual reality software in this research, the changes of stress index were observed between synchronized status of Road Bike hardware and virtual reality software and not synchronized status. The virtual reality Road Bike which is synchronized with 3D virtual reality environment and mechanically works the same way with real bike allows a users not only to increase the effectiveness of exercise but also to reduce significantly the boredom compare to traditional indoor bike. The prototype of virtual realty Road Bike has been completed, detailed research will be conducted in the future to increase a user‘s safety and provide a more similar experience with real Road Bike for adapting various industry fields especially in the game industry.

The development of machining technology has coincided with the recent development of a diverse amount of materials and tools. The developed materials largely consist of hardened steel for vehicle and the mechanical industry. The machining of the hardened steel is performed in a lathe and many kind of machining centers, but it is difficult to machine because its hardness is the most difficult-to-cut materials. Hard-turning is a kind of machining process which omits the final grinding process and replaces it with a single accurate cutting process. In this paper, the turning of SKD 11(HRC 58) was performed using the CBN tool in order to recognize the optimum process conditions. The cutting force, tool life and wear, surface roughness were measured. Examining the machining characteristics when cutting of high hardened steel, low cutting speed and high conveying speed were identified to be effective in cutting conditions of SKD 11. Tool life was most effective in the conditions with 65m/min of cutting speed and 0.193mm/rev of feedrate and approximately 0.5um of very good surface profile was acquired at 0.079mm/rev of feedrate. Therefore, when cutting with Low CBN tool, it could be considered to be sufficient in reducing the steps of precision machining or replacing the polishing

In ruminants, Interferon-τ (IFN-τ) has the role of recognizing pregnancy signals produced by the embryo and it may have an important role during the luteolysis. Therefore, the purpose of the present study was to investigate the effect of IFN-τ on prostaglandin synthesis, cyclooxygenase-2 (COX-2) gene expression in vitro and secretion of progesterone (P4) in vivo. The epithelial and stromal cells isolated from bovine endometrium were cultured with different doses of IFN-τ (0, 0.02, 0.2 and 2 μg/ml). Human chorionic gonadotropin (hCG, 1.5 IU/ml) was used as a positive control. Prostaglandin E2 and F2α levels in the culture media were analyzed by enzyme immunoassays, and total RNA was extracted from the cells for RT-PCR. P4 concentrations in blood samples were assayed by chemiluminescent immunoassay system. In epithelial cells, COX-2 gene expression was increased in the presence of IFN-τ (p<0.05), but it was not significantly different in all groups of stromal cells except 2 μg/ml IFN-τ group (p<0.05). Although IFN-τ did not affect PGE2 and PGF2α production in epithelial cells, it decreased PGE2 and PGF2α production significantly in stromal cells (p<0.05). In vivo experiment, the P4 concentrations in blood sample was significantly increased after injection of 1 μg/ml IFN-τ. These results indicate that PG production was mediated by COX-2 expression in the stromal cells but it did not affect in the epithelial cells, and suggest that treatment of IFN-τ was to improve the implantation environment of uterine by maintenance of high P4 concentration. * This work was carried out with the support of “Cooperative Research Program for Agriculture Science & Technology Development (Project No. PJ907008)” Rural Development Administration, Republic of Korea.

Experimental measurements of flame shape and heat transfer characteristics were performed for impinged inverse diffusion flame(IDF) using propane as a fuel. The purpose of this study is to identify the favorable co-axial inverse diffusion flame structure for impingement heating. The flame consisted of an entrainment zone and mixing and combustion zone. The heat flux which represents heat transfer rate is measured by using a heat flux sensor that is located at the center of the impingement plate. The inverse diffusion flame structure has been classified into six modes. In these modes, several favorable flames for impingement heating were identified. In this study, the parameters are overall equivalent ratio(Φ), nozzle to impingement plate distance(h/d), vertical distance from the stagnation point and Reynolds number(Re) of combustion air.