The purpose of this study is to analyze the structural stability of pavement due to water infiltration at the road with infiltration trench as using the FEM(finite element analysis). Five cases for FEM is divided considering the amount of rainfall and rain duration time. The results of FEM show that the more rainfall in a short period time is faster the change of moisture content. Also, it is the proportional relationship between and changing area of moisture content of more than 40% due to rainfall. Case 3 and 4 are necessary to check the installation of infiltration trench because of moisture content of more than 40%, recovery time of initial moisture content, and changing area of more than 40%. Case 1,2, and 5 have no a significant effect on road pavement structure due to lower moisture content and shorter duration time of higher moisture content.

본 연구에서는 프리스트레스트 콘크리트 보의 처짐 예측을 위해 재료비선형이 고려된 콘크리트 및 철근, 강연선의 거동을 고려할 수 있는 구성모델을 조합하여 적층 쉘 요소를 사용한 유한요소해석 모델에 적용하였다. 이를 기존 연구자들의 실험결과와 비교함으로써 모델의 타당성을 검증하였고, 스팬-깊이비, 편심 그리고 프리스트레싱 크기에 대한 처짐을 해석하고 이를 수계산 결과와 비교하였다. 그 결과, 스팬-깊이비가 커질수록, 편심이 작아질수록, 프리스트레싱 크기가 작아질수록 처짐이 증가하는 것을 확인하였다. 또한, 편심이 매우 작을 경우와 프리스트레싱 크기가 매우 작을 경우에는 수계산이 처짐을 과대평가한다는 것을 확인하였다.

In this study, the behavior of densification of copper powders during high-pressure torsion (HPT) at room temperature is investigated using the finite element method. The simulation results show that the center of the workpiece is the first to reach the true density of copper during the compressive stage because the pressure is higher at the center than the periphery. Subsequently, whole workpiece reaches true density after compression due to the high pressure. In addition, the effective strain is increased along the radius during torsional stage. After one rotation, the periphery shows that the effective strain is increased up to 25, which is extensive deformation. These high pressure and severe strain do not only play a key role in consolidation of copper powders but also make the matrix harder by grain refinement.

A strain-gradient crystal plasticity constitutive model was developed in order to predict the Hall Petch behavior of a Ni-base polycrystalline superalloy. The constitutive model involves statistically stored dislocation and geometrically necessary dislocation densities, which were incorporated into the Bailey-Hirsch type flow stress equation with six strength interaction coefficients. A strain-gradient term (called slip-system lattice incompatibility) developed by Acharya was used to calculate the geometrically necessary dislocation density. The description of Kocks-Argon-Ashby type thermally activated strain rate was also used to represent the shear rate of an individual slip system. The constitutive model was implemented in a user material subroutine for crystal plasticity finite element method simulations. The grain size dependence of the flow stress (viz., the Hall- Petch behavior) was predicted for a Ni-base polycrystalline superalloy NIMONIC PE16. Simulation results showed that the present constitutive model fairly reasonably predicts 0.2%-offset yield stresses in a limited range of the grain size.

The porous metallic material has the most superior physical property and the best mechanical capability. This study is investigated with the simulation analysis by compressing three kinds of specimens. Three aluminum foams with the thickness of 10 mm are bonded at Case 1. Two aluminum foams with the thicknesses of 10 mm and 20 mm are bonded at Case 2. It is one aluminum foam with the thickness of 30 mm at Case 3. The two dimensional model is done by ANSYS design modeler and the finite element analysis is performed by ANSYS structural analysis. As the forced displacement of 1 mm during the elapsed time of 60 sec is applied, the forced displacement of 10 mm during the total elapsed time of 600 sec is applied. As the analysis result, the most reaction force is shown at case 2 among three cases. Case 2 is estimated as the best structure. The analysis result of this study is thought to be the data necessary for the safe design about mechanical structure and the development of composite material.

A progressive failure analysis procedure for composite laminates is completed in here. An anisotropic plastic constitutive model for fiber-reinforced composite material is implemented into computer program for a predictive analysis procedure of composite laminates. Also, in order to describe material behavior beyond the initial yield, the anisotropic work-hardening model and subsequent yield surface are implemented into a computer code, which is Predictive Analysis for Composite Structures (PACS). The accuracy and efficiency of the anisotropic plastic constitutive model and the computer program PACS are verified by solving a number of various fiber-reinforced composite laminates with and without geometric discontinuity. The comparisons of the numerical results to the experimental and other numerical results available in the literature indicate the validity and efficiency of the developed model.

The automotive bumper has the functions of strength, rigidity and fine sight. It protects the driver, front and rear sides of car body through shock absorption at the traffic accident of car. This study investigates the impacts on front side and corner with the low speed of 4.5 km/h by using the model of SUV car body. The models are modelled by CATIA program with three dimensions and are analyzed by the finite element program of ANSYS Explicit STR. The maximum equivalent stresses at impacts of front side(case 1) and corner (case 2) at bumper are 261.72MPa and 365.02MPa respectively. As this stress at case 2 becomes 40% higher than at case 1, the impact of corner is happened easier than at the damage at the impact of front side. These stresses at case 1 and case 2 are shown above the yield stress at material property of steel, it is thought that there are the possibilities of plastic damages at two cases. The maximum deformation and equivalent stress at the support 2 of case 2 become 5 times and 3 times higher than at the support 1 respectively. The damage possibility due to impact at low speed is investigated by the basic analysis result of this study. And this result can be utilized at inspecting the result of impact test on bumper hereafter.

최근 국내 이상기후로 인한 집중호우로 사회기반 시설물인 도로 파손 문제가 대두 되고 있다. 이를 해 결하기 위해 아산탕정지구에 840개의 침투도랑을 포함한 LID(Low Impact Development) 빗물관리시설 물이 도로인접부에 설치되었다. 하지만 침투도랑에 유입된 유입수의 거동이 침투도랑 인접 부도로 내부로 흘러들어가 도로구조의 안정성에 부정적인 영향을 발생시킬 가능성이 있다. 그럼에도 불구하고 도로안전 성을 검증하기 위한 실내시험 및 현장시험은 전무한 상태이다. 본 연구에서는 실내시험 및 현장시험을 보다 정확히 하기 위하여 침투수에 의한 도로안정성 구조해석 이 필수적인 사항이라고 판단하였다. 침투수 유입에 따른 도로하부구조의 유체거동과 포장골재 및 노상의 함수비 변화에 따른 공용성을 분석하였다. 도로하부구조의 유체거동과 함수비 변화를 역학적으로 예측하 기 위해 유한요소 해석을 실시하였다. 유한요소 해석을 통해 침투도랑이 도로 공용성에 미치는 영향 분석 의 전체적인 연구 절차는 아래 그림 1과 같다.

The latest weight reduction research of automotive industry and technology was improved. In this paper, we aim to evaluate the composite frame to manufacture the floor assembly of commercial vehicle. The design of subframe incorporated into the floor module was determined by FEM(Finite Element Method) simulation. The mechanical properties used for the simulations were obtained from the tests for samples of glass fiber/epoxy composites. We made two kinds of pultrusion products, one was aluminum profile, the other was unidirectional composites with aluminum profile. Based on the results from the simulation and bending test, the design of the subframe was finally determined prior to adoption of the commercial vehicle floor.

동역학의 새로운 변분이론인 혼합 합성 변분이론은 수학물리학을 비롯한 공학에 있어 초기치-경계치 문제해석에 광범위하게 적용될 수 있는 기반을 제공하는 것으로, 본 논문은 이 이론을 토대로 시간에 대한 이차의 형상함수가 적용된 시간 유한요소해석법을 개발하고 그 해석법의 수치특성 확인을 통해 향후 다양한 동적시스템 해석의 적용에 대한 가능성을 살펴보았다. 이를 위해 가장 기본적인 선형탄성의 단자유도계가 고려되었다. 에너지 보존시스템의 경우(비감쇠 시스템에 외력이 작용치 않는 경우), 제안된 알고리즘 모두는 time-step에 관계없이 안정적이며 수치감쇠가 없이 에너지와 모멘텀이 보존되는 symplecticity property를 가지고 있음을 확인할 수 있었고, 감쇠시스템인 경우, time-step이 점점 작아질수록 정확한 해에 빠르게 수렴하는 것을 확인하였다.

본 연구에서는 비선형 유한요소 해석 기법을 적용한 격납건물의 내압취약도 평가를 수행하였다. 대상 구조물은 국내 대표적인 가압경수로형 원전 격납건물 중 하나로 하였다. 비선형 극한내압 해석을 위해 대규모 개구부를 고려한 격납건물의 3차원 유한요소 모델을 도출하였다. 재료 특성 및 구조적 성능에 내포된 불확실성을 고려하기 위하여 각 변수들의 변동성에 대한 극한내압 성능의 민감도 해석을 수행하였다. 민감도 해석 결과를 통해 확률론적 내압 취약도 평가를 위한 불확실성 변수 및 분포 특성을 도출하였다. 현재의 텐던 긴장력 상태를 고려하기 위하여 가동 중 검사 보고서에 기록된 텐던 긴장력 값을 중앙값으로 적용하였다. 누설(leak)과 파단(rupture)을 파괴모드로 정의하고, 각각에 대한 극한내압 취약도 평가를 위하여 한계상태를 정의하였다. 각 파괴모드에 대한 대상 격납건물의 내압취약도를 내압 성능 중앙값, 고신뢰도 저파괴확률 성능값, 신뢰도 수준에 따른 취약도 곡선을 통하여 제시하였다. 누설 및 파단 파괴모드에 대한 고신뢰도 저파괴확률값은 각각 0.7991 MPa, 0.8691 MPa로 평가되었다.

본 논문에서는 범용 유한요소프로그램 ANSYS와 ABAQUS를 이용하여 냉간성형강으로 조립한 조립기둥의 전체좌굴과 뒤틀림좌굴에 대한 비선형해석을 위한 모델링 기법을 소개한다. 냉간성형강의 경우 두께가 얇아서 국부좌굴 등 비선형거동을 보이기 때문에 좌굴에 대한 해석에 매우 섬세한 모델링이 필요하다. ANSYS의 내연적정적모델링에 의한 해석은 좌굴 극한점 부근에서 수렴의 문제를 발생하였지만, ABAQUS의 외연적동적모델링의 경우에는 좌굴 및 좌굴이후의 부재 거동에 대해서 안정적인 결과를 제공하였다. 또한 수치해석 결과는 좌굴실험을 통해 얻어진 축내력에 비해 높은 내력을 보여주고 있다. 이는 실험과정에서 발생하는 편심에 의한 영향으로서 수치해석에 의한 좌굴내력에 적정한 보정치의 적용이 필요하며 본논문에서는 기존 실험데이터와의 비교를 통해 0.88의 값을 제시한다.

PURPOSES : This paper numerically evaluates the contribution of transverse steel to the structural behavior of continuously reinforced concrete pavements to understand the role of transverse steel. METHODS: Two-lane continuously reinforced concrete pavements with and without transverse steel were analyzed through finite element analysis with the aid of commercial finite element analysis program DIANA; the difference in their structural behavior such as deflection, joint opening, and stress distribution was then evaluated. Twenty-node brick elements and three-node beam elements were used to model concrete and steel, respectively. Sub-layers were modeled with horizontal and vertical tensionless spring elements. The interactions between steel and surrounding concrete were considered by connecting their nodes with three orthogonal spring elements. Both wheel loading and environmental loading in addition to self-weight were considered. RESULTS : The use of transverse steel in continuously reinforced concrete pavements does not have significant effects on the structural behavior. The surface deflections change very little with the use of transverse steel. The joint opening decreases when transverse steel is used but the reduction is quite small. The transverse concrete stress, rather, increases when transverse steel is used due to the restraint exerted by the steel but the increase is quite small as well. CONCLUSIONS : The main role of transverse steel in continuously reinforced concrete pavements is supporting longitudinal steel and/or controlling unexpected longitudinal cracks rather than enhancing the structural capacity.

In order to overcome the key shortcoming of Hamilton's principle, recently, the extended framework of Hamilton's principle was developed. To investigate its potential in further applications especially for material non-linearity problems, the focus is initially on a classical single-degree-of-freedom elasto-viscoplastic model. More specifically, the extended framework is applied to the single-degree-of-freedom elasto-viscoplastic model, and a corresponding weak form is numerically implemented through a temporal finite element approach. The method provides a non-iterative algorithm along with unconditional stability with respect to the time step, while yielding whole information to investigate the further dynamics of the considered system.

Numerical analysis of a Ni-PZT stacked piezoelectric micro actuator is investigated for the prediction of mechanical behavior as a preceding research for the manufacturing of three dimensional micro structures. Finite element method is adopted to examine the simulation of a piezoelectric actuator according to applied direction of voltage, by researching displacement characterization of piezoelectric material through piezoelectric theory. PZT-4 is selected as a piezoelectric material. And bimorph finite element modeling is employed to study the response of Ni-PZT bi-layered micro actuator under the various input voltages. The results are presented as maximum displacement values under each applied voltages. Maximum displacement of 0.71μm at 60V is obtained

In this study, porous titanium samples were manufactured by space holder methods using two kinds of urea and sodium chloride space holders. Three-dimensional pore structures were obtained by a computed-tomography (CT) tech- nique and utilized for finite element analysis in order to investigate the mechanical properties. The CT-based finite ele- ment analyses were in better agreement with the experimental results than unit cell model-based analyses. Both the experimental and CT-based results showed the same tendency that the elastic modulus decreased with increasing the porosities. The total porosity of the bulk body plays a key role in determining the elastic modulus of porous materials.

New material which absorbs impact energy effectively and has excellent mechanical property is developed. The used amount is increased at automobile field day by day. Aluminum foam with various air sell lattices within is one of representative porosity metals which are used at many automobile parts because it has the excellent lightness and impact energy absorption function. For this reason, aluminum foam is used widely as a component among composite materials. This study aims to investigate systematically the mechanical property of foam through computer simulation. In order to obtain the property of aluminum foam, aluminum foam is designed as the dimension of 100mm × 100mm × 25mm and the striker that has the diameter of 12.5mm is supposed to impact aluminum foam with impact energies of 6J, 10J, and 14J. Aluminum foam is not penetrated when striker given by energy of 6J or 10J impacts into it, but aluminum foam is penetrated by striker in case of impact energy of 14J. The result can provide the basic data in order to develop the advanced composite material.

본 논문에서는 도심지 지하에 터널 전력구를 건설하는 경우 시공단계별 영향을 고려한 구조해석을 수행하였다. 해석대상의 도심지 지하에는 여러 종류의 다양한 라이프라인 구조체가 설치되어 있다. 터널전력구의 구조해석에는 지반체의 유한요소해석 프로그램인 MPDAP을 사용하였다. 라이프라인 구조체와 터널 전력구 사이의 이격거리가 가장 작은 대표적인 3개의 단면에 대하여 구조해석을 수행하였다. 터널의 굴착단계별 유한요소해석에서 발생되는 평형불균형성 문제는 평형섭동개념을 적용하여 해결하였다. 또한 터널 굴착에 의한 시간의존 변형의 영향은 하중분담율을 사용하여 시공단계별로 고려하였다. 본 연구에서 검토한 3개의 대표단면에서는 터널 전력구 주변 지반체에서 발생하는 최대변위값은 허용변위값이내를 보여주었다.