The Alkali-Metal Thermal to Electric Converter (AMTEC) can be used as a next-generation power generation technology related with a large thermal energy storage. In particular, this technology is expected for the higher efficiency by a cascade power generation with the thermoelectric generator(TEG), and the temperature distribution becomes a very important design parameter in this case. In this study, the temperature distribution of the AMTEC unit was analyzed through CFD analysis, and design points were discussed based on the results.

Radiation dose rates for spent fuel storage casks and storage facilities of them are typically calculated using Monte Carlo calculation codes. In particular, Monte Carlo computer code has the advantage of being able to analyze radiation transport very similar to the actual situation and accurately simulate complex structures. However, to evaluate the radiation dose rate for models such as ISFSI (Independent Spent Fuel Storage Installation) with a lot of spent fuel storage casks using Monte Carlo computational techniques has a disadvantage that it takes considerable computational time. This is because the radiation dose rate from the cask located at the outermost part of the storage facility to hundreds of meters must be calculated. In addition, if a building is considered in addition to many storage casks, more analysis time is required. Therefore, it is necessary to improve the efficiency of the computational techniques in order to evaluate the radiation dose rate for the ISFSI using Monte Carlo computational codes. The radiation dose rate evaluation of storage facilities using evaluation techniques for improving calculation efficiency is performed in the following steps. (1) simplified change in detailed analysis model for single storage cask, (2) create source term for the outermost side and top surface of the storage cask, (3) full modeling for storage facilities using casks with surface sources, (4) evaluation of radiation dose rate by distance corresponding to the dose rate limit. Using this calculation method, the dose rate according to the distance was evaluated by assuming that the concrete storage cask (KORAD21C) and the horizontal storage module (NUHOMS-HSM) were stored in the storage facility. As a result of calculation, the distance to boundary of the radiation control area and restricted area of the storage facility is respectively 75 m / 530 m (KORAD21C case), and 20 m / 350 m (NUHOMS-HSM case).

The saturation rates of the spent fuel (SF) wet storage at the Kori Nuclear Power Plant (NPP), Hanbit, and Hanul are 83.3%, 74.2%, and 80.8% as of the fourth quarter of 2021. The storages of Kori NPP and Hanbit NPP are expected to be saturated in 2031, and Hanul is expected to be saturated in 2032. Therefore, the construction of an interim storage facility to store the SF temporarily stored in the NPP was planned, and preparations for the safe transport of the SF are required. In this paper, radiological preliminary assessment using NRC-RADTRAN in the process of sea transport of SF from the wet storage or ISFSI of the Hanbit NPP to the optional interim storage facility was performed. Since domestic SF transport vessels are not currently in operation, the specifications of the UK Pacific Grebe vessel which can carry up to 20 casks were used. The transport cask used the specifications of KORAD-21, a transport container developed in Korea. Because it can carry more SF assemblies than the existing KN-18. In addition, a land transport safety test was conducted in 2020 and a sea transport test is planned. The sea transport route was entered by referring to the transport route of domestic low and intermediate level waste. The accidents rate was calculated using statistics on maritime accidents from 2017 to 2021. The probability accidents along the transportation route were evaluated as 3.152E -10. When transporting to an interim storage facility, the SF expected to be the main transport target was selected as WH 17X17, combustion 45,000 MWD/MTU, and concentration of 4.5%. The source term was calculated and entered according to this data and the release fraction was entered with reference to the DOE report. In the case of normal transport without accident, the individual dose of the crew member and public residents were estimated to be 0.0525% and 0.000492% of the annual limit of 1 mSv/yr for the general public. Under the accident conditions, the annual individual doses of residents were 0.0011%, 0.0023%, 0.0034%, and 0.0046% of the annual limit of 1 mSv/yr when carrying 5, 10, 15, and 20 casks. Currently, the site of the interim storage facility has not been precisely determined, but a preliminary radiation assessment through sea transport resulted in a significantly lower than the limit. Combined scenario sea transport followed by land transport will be carried out in the next stage of study.

As the amount of on-site Spent Nuclear Fuel (SNF) in storage increases due to the continued operation of Nuclear Power Plants (NPPs) in Korea, the on-site wet storage pool is expected to become saturated. Therefore, a facility for safely storing the spent nuclear fuel is required so that there is no problem with operation of the NPP until permanent disposal of SNF. Prior to the construction of such a facility, the safety analysis of the interim storage facility and verification of the safety of the spent fuel storage system (e.g. cask, silo) to be used are required according to Article 63 of the Nuclear Safety Act. In this process, analysis of the Structures, Systems, and Components (SSCs) of the storage system is needed. Based on the analysis, it is necessary to efficiently classify SSCs that are important to safety in order to differentiate management that more thoroughly manages those important to safety. In Korea, according to the notice of the Nuclear Safety and Security Commission, the components performing essential safety functions for the safe storage of spent fuel storage system are to be classified as “important safety equipment”. 10 CFR Part 72, a federal regulation related to interim storage facilities in the United States, also requires the identification of SSCs that fall under “Important to Safety (ITS)”, which is like domestic case. In addition, it has been confirmed that there are cases in which detailed classification according to Reg Guide 7.10 and NUREG-CR/6407 is added in Safety Analysis Report. However, these existing classification methods are not only classified as a single grade except for the method according to the Reg guide, but all are classified according to a qualitative standard. Qualitative criteria may cause ambiguity in judgment, resulting in subjective judgment of the person who proceeds in the classification process. Therefore, in this study, a new classification method is proposed to solve the problem according to the qualitative classification method. Assessing the level of radiological harm to the general public due to the assumption of failure of SSC in the spent fuel storage system is used as a quantitative evaluation standard.

Some Spent Fuel Pools (SFPs) will be full of Spent Nuclear Fuels (SNFs) within several years. Because of this reason, building interim storage facilities or permanent disposal facilities should be considered. These storage facilities are divided into wet storage facilities and dry storage facilities. Wet storage facility is a method of storing SNF in SFP to cool decay heat and shielding radiation, and dry storage facility is a method of storing SNF in a cask and placing on the ground or storage building. However, wet storage facilities have disadvantages in that operating costs are higher than that of dry storage facilities, and additional capacity expansion is difficult. Dry storage facilities have relatively low operating costs and are relatively easy to increase capacity when additional SNFs need to be stored. For this reason, since the 1990s, the number of cases of applying dry storage facilities has been increasing even abroad. Dry storage facilities are divided into indoor storage facilities and outdoor storage facilities, and outdoor storage facilities are mostly used to take advantage of dry storage facilities. In the case of outdoor storage facilities, the cask in which SNFs are stored is placed on a designed concrete pad. During this storage, the boring heat generated by SNFs cools into natural convection and the cask shields the radiation that SNFs generates. However, if an accident such as an earthquake occurs and the cask overturns during storage, there may be a risk of radiation leakage. Such a tip-over accident may be caused by the cask slipping due to the vibration of an earthquake, or by not supporting the cask properly due to a problem in the concrete pad. Therefore, in the case of outdoor dry storage facilities, it is necessary to evaluate the seismic safety of concrete pads. In this paper, various soil conditions were applied in the seismic analysis. Soil conditions were classified according to the shear wave velocity, and the shear wave velocity was classified according to the ground classification criteria according to the general seismic design (KDS 17 10 00). The concrete pad was designed with a size that 8 casks can be arranged at regular intervals, and 11# reinforcing bars were used for the design of the internal reinforcement of the concrete pad according to literature research. The cask was designed as a rigid body to shorten the analysis time. The soil to which the elastic model was applied was designed under the concrete pad, and infinite elements were applied to the sides and bottom of the soil. The effect on the concrete pad and cask by applying a seismic wave conforming to RG 1.60 to the bottom of the soil was analyzed with a finite element model.

Due to the saturation of the on-site storage capacity of spent nuclear fuel within a few years, dry storage facility should be introduced. However, it is unclear when to start operating the dry storage facility, so in case of Kori Unit 1, which is being decommissioning, the spent fuel must be stored in the spent fuel pool of another power plant. In addition, in the case of damaged fuel, it is impossible to transfer and store it with general handling methods. Therefore, a damaged fuel canister (DFC) should be able to handle damaged or failed fuel as intact fuel, and both wet and dry storage should be possible. The canister developed by Korea Hydro & Nuclear Power is designed to satisfy criticality, shielding, cooling performance, and structural integrity in accordance with NUREG-1536 and 2215. In addition, it can be handled as existing fuel handling devices rather than new handling tools. Fastening of the DFC lid and body in the spent fuel pool is possible with a hexagonal socket wrench, one of the fuel repair tools. And it is designed to facilitate visual identification of whether it is fastenedor not. The lifting method for transferring DFC to another facility is the same as the nuclear fuel lifting method. And a unique sealing and mesh structure of the lid and body is devised to completely block leakage of nuclear fuel fragments of 0.2 mm or more during vacuum drying for dry storage. The usability of DFC has been verified through test operation of the prototype, and it will be manufactured before discharging spent fuel for the decommissioning of Kori Unit 1.

For Dry Storage of Spent Nuclear Fuel (SNF), all moisture must be removed from the dry storage canister through subjected to a drying process to ensure the long-term integrity. In NUREG-1536, the evacuation of most water contained within the canister is recommended a pressure of 0.4 kPa (3 torr) to be held in the canister for at least 30 minutes while isolated from active vacuum pumping as a measure of sufficient dryness in the canister. In the existing drying process, the determination of drying end point was determined using a dew point sensor indirectly. Various methods are being studied to quantify the moisture content remaining inside the canister. We presented a moisture quantification method using the drying process variables, like as temperature, pressure, and relative humidity operation data. During the drying process, it exists in the form of a mixed gas of water vapor and air inside the canister. At this time, if the density of water vapor in the mixed gas discharged out of the canister by the vacuum pump is known, the mass of water removed by vacuum drying can be calculated. The canister is equipped with a pressure gauge, thermometer and dew point sensor. The density of water vapor is calculated using the pressure, temperature and relative humidity of the gas obtained from these sensors. First, calculate the saturated water vapor pressure, and then calculate the humidity ratio. The humidity ratio refers to the ratio of water vapor mass to the dry air mass. After calculating the density of dry gas, multiply the density by the humidity ratio to calculate the density of water vapor (kg/m3). Multiply the water vapor density by the volume flow (m3/s) to obtain the mass value of water (kg). The calculated mass value is the mass value obtained per second since it is calculated through the flow data obtained every second, and the amount of water removed can be obtained by summing all the mass values. By comparing this value with the initial moisture content, the amount of moisture remaining inside the canister can be estimated. The validity of the calculations will be verified through an experimental test in the near future. We plan to conduct various research and development to quantify residual water, which is important to ensure the safety of the drying process for dry storage.

This study reassess safety margin of the current Peak Cladding Temperature (PCT) limit of dry storage in terms of hydrogen migration by predicting axial hydrogen diffusion throughout dry storage with respect to wet storage time and average burnup. Applying the hydride nucleation, growth, and dissolution model, an axial finite difference method code for thermal diffusion of hydrogen in zirconium alloy was developed and validated against past experiments. The developed model has been implemented in GIFT – a nuclear fuel analysis code developed by Seoul National University. Various discharge burnups and wet storage time relevant to spent fuel characteristics of Korea were simulated. The result shows that that the amount of hydrogen migrated towards the axial end during dry storage for reference PWR spent fuel is limited to ~50 wppm. This result demonstrates that the current PCT margin is sufficient in terms of hydrogen migration.

To minimize the short-term thermal load on the repository facility, heat generating nuclides such as Cs-137 and Sr-90 should be separated from the spent nuclear fuel for efficiency of repository facility. In particular, Sr-90 must be separated because it generates high heat during the decay process. Recently, Korea Atomic Energy Research Institute (KEARI) is developing a waste burden minimization technology to reduce the environmental burden caused by the disposal of spent nuclear fuel and maximize the utilization of the disposal facility. The technology includes a nuclide management process that can maximize disposal efficiency by selectively separating and collecting major nuclides such as Cs, Sr, I, TRU/RE, and Tc/Se from spent nuclear fuel. Among the major nuclides, Sr nuclides dissolve in chloride phase during the chlorination process of spent nuclear fuel and recovered in the form of carbonate or oxide via reactive distillation. In this process, Ba nuclides are also recovered along with Sr nuclides due to their chemical similarity. In this study, we prepared group II nuclide ceramic waste form, Ba(x)Sr(1-x)TiO3 (x=0, 0.25, 0.5, 0.75, 1), using the solid-state reaction method by considering the various ratio of Sr/Ba nuclides generated from nuclide management process. The established waste form fabrication process was able to produce a stable waste form regardless of the ratio of Sr/Ba nuclides. To evaluate the stability of group II waste form, physicochemical properties such as leaching and thermal properties were evaluated. Also, the radiological properties of the Ba(x)Sr(1-x)TiO3 waste forms with various Sr/Ba ratios were evaluated, and the estimation of centerline temperature was carried out using the experimental thermal property data. These results provided fundamental data for long-term storage and management of group II nuclides waste form.

The IAEA states that in the event of sabotage, nuclear material and equipment in quantities that can cause high radiological consequences (HRC), as well as the minimum systems and devices necessary to prevent HRC, must be located within one or more vital areas. Accordingly, in Article 2 of the ACT ON PHYSICAL PROTECTION AND RADIOLOGICAL EMERGENCY, the definition of the vital area is specified, and a nuclear facility operator submits a draft to the Nuclear Safety and Security Commission to establish vital areas and must obtain approval from Nuclear Safety and Security Commission. Since the spent fuel pool and new fuel storage area are areas where nuclear material is used and stored, they can be candidates for vital areas as direct targets of sabotage. The spent fuel pool is a wet spent fuel storage facility currently operated by most power plants in Korea to cool and store spent nuclear fuel. Considering the HRC against sabotage, it is necessary to review whether sepnt fuel pool needs to establish a vital area. In addition, depending on the status of plant operation during the spent fuel management cycle, the operation status of safety systems to mitigate accidents and power system change, so vital areas in fuel handling building (including spent fuel pool) also need to be adjusted flexibly. This study compares the results of the review on whether the essential consideration factors are reflected in the identification of essential safety systems and devices to minimize HRC caused by sabotage in the spent fuel storage system with the procedure for identifying the vital area in nuclear power plants. It was reviewed from the following viewpoints: Necessity to identify necessary devices to minimize the radiation effects against sabotage on the spent fuel pool, Review of necessary elements when identifying vital areas to minimize the radiation effects of spent fuel pool against sabotage, Necessity to adjust vital areas according to the spent fuel management cycle. The main assumptions used in the analysis of the vital area of the power plant need to be equally reflected when identifying vital areas in spent fuel pool. And, the results of this study are for the purpose of minimizing the radiological consequences against sabotage on the spent fuel storage system including the spent fuel pool and used to establish regulatory standards in the spent fuel storage stage.

The acoustic emission (AE) is proposed as a feasible method for the real-time monitoring of the structural damage evolution in concrete materials that are typically used in the storage of nuclear wastes. However, the characteristics of AE signals emitted from concrete structures subjected to various environmental conditions are poorly identified. Therefore, this study examines the AE characteristics of the concrete structures during uniaxial compression, where the storage temperature and immersion conditions of the concrete specimens varied from 15℃ to 75℃ and from completely dry to water-immersion, respectively. Compared with the dry specimens, the water-immersed specimens exhibited significantly reduced uniaxial compressive strengths by approximately 26%, total AE energy by approximately 90%, and max RA value by approximately 70%. As the treatment temperature increased, the strength and AE parameters, such as AE count, AE energy, and RA value, of the dry specimens increased; however, the temperature effect was only minimal for the immersed specimens. This study suggests that the AE technique can capture the mechanical damage evolution of concrete materials, but their AE characteristics can vary with respect to the storage conditions.

본 연구에서는 수확 후 저장 기간에 따른 절화 장미의 수명 변화를 알아보았다. 절화장미 ‘Antique Curl’을 수확 직후 4℃ 암조건의 저장고에서 0일(무처리), 1일, 3일, 5일, 7일간 보존 용액 처리 후 습식 저장하였다. 저장이 끝난 절화는 24℃ 실 내 광환경으로 옮겨 절화 보존제 유무 조건에서 절화수명을 조사하였다. 그 결과, 절화수명은 저장기간 3일차까지는 20일 전후로 높았으나, 5일차 이후 유의적으로 감소했다. 절화 보 존제는 절화수명 연장에 효과적이지는 않았으나 절화의 꽃목 굽음 현상을 완화시켰다. 엽록소 형광(Fv/Fm)은 저장 기간과 관계없이 0.78~0.82 수준으로 나타났으며 저장기간에 의한 광 생리 기능저하는 확인되지 않았다. 결과적으로 절화장미 ‘Antique Curl’의 상업적 저장 기한은 최대 5일로 확인되었다.

The development of technology related to the Fourth Industrial Revolution and the growth of the online market due to pandemic are continuing the growth of the logistics market for product delivery. If it is difficult to deliver the product directly to the customer during delivery, storage and delivery using the unmanned courier box are being carried out. However, existing storage boxes are not actively used due to lack of usability even though they have the advantage of storing goods and delivering non-face-to-face. In addition, existing courier boxes are not prepared for cold chain transportation. The unmanned delivery storage device with ICT cold chain technology should be developed to prepare for the transition to non-face-to-face society, to improve logistics efficiency and meet user's requirements. Also, it is necessary to consider the measures to reduce the safety problems that may occur during the use and maintenance of the automatic system.This study conducted a model-based analysis for the development of unmanned delivery storage devices with ICT cold chain technology, and conducted a study to derive the system development specifications that meet the requirements and secure safety and apply them to the development process.

A simplified method for earthquake response analysis of a rectangular liquid storage tank is proposed with fluid-structure interaction considered. In order to simplify the complex three-dimensional structural behavior of a rectangular liquid storage tank, it is assumed that structural deformation does not occur in the plane parallel to the direction in which the earthquake ground motion is applied but in the plane perpendicular to the direction. The structural deformation is approximated by combining the natural modes of the simple beam and the cantilever beam. The hydrodynamic pressure, the structure’s mass and stiffness, and the hydrodynamic pressure’s added mass are derived by applying the Rayleigh-Ritz method. The natural frequency, structural deformation, pressure, effective mode mass, and effective mode height of the rectangular liquid storage tank are obtained. The structural displacement, hydrodynamic pressure, base shear, and overturning moment are calculated. The seismic response analysis of an example rectangular liquid storage tank is performed using the proposed simplified approach, and its accuracy is verified by comparing the results with the reference solution by the finite element method. Existing seismic design codes based on the hydrodynamic pressure in rigid liquid storage tanks are observed to produce results with significant errors that cannot be ignored.

In preparation of porous carbon materials microwave oven brightening is one of the warming modes used ever. The various procedures that take place in microwave combustion process include carbonization, incitation, and recovery and thus carbon is defined. This paper compares ideal conditions of traditional warming methods, as well as their implementation potential, losses, and specifications. This porous carbon with heat treatment possesses various properties and they are well suited for energy applications which require constrained space such as hydrogen storage in solid-state and supercapacitors. The enhanced properties are chemical and thermal stability, ready availability, low framework density and ease of processability. The recent trend in class of porous carbons is Activated Carbons that are employed traditionally as adsorbents or catalyst supporters but currently, they found potent applications in fabricating for hydrogen storage materials and supercapacitors. These activated carbons are much enhanced form in class of porous carbon materials and they possess the capability to enable hydrogen economy, where the energy carrier is hydrogen. Therefore, the utility of activated carbons as a source for energy storage experiences a rapid growth at current trend and they possess significant advances. This investigation is based on detailed cost development data and electrical imperativeness applications.

To improve the shelf-life of Centella asiatica, Centella asiatica was treated with gel packs containing slow-released chlorine dioxide (ClO2) gas at 3-5 ppm for 20 days at 4℃. The weight loss rate, as well as the changes in pH, color, and texture of the treated samples, were investigated. The weight of the control and ClO2 gas-treated samples was decreased during the storage period. The change in weight of the control was slightly faster than that of the samples treated with 3 and 4 ppm ClO2 gas. The pH of the control and the ClO2 gas treated samples were decreased during the storage period and there was no significant difference between the control and ClO2 gas treated samples. Concerning color (lightness, redness, and yellowness) changes of Centella asiatica during the storage period, there was no significant difference between the control and ClO2 gas treated samples. The change in shear force in the leaf and stem of Centella asiatica during the storage period was slightly lower in the 4 ppm ClO2 gas treated samples (in the leaf) compared to the control and 3 and 4 ppm ClO2 gas treated samples (in the stem) compared to the control and 5 ppm ClO2 gas treated sample.

Three government bodies, that is, the Ministry of Science and ICT (MSIT), Ministry of Trade, Industry, and Energy (MOTIE), and Nuclear Safety and Security (NSSC), jointly established the Institute for Korea Spent Nuclear Fuel (iKSNF) in December 2020 to secure the management technologies for spent nuclear fuel (SNF). The objective of iKSNF is to successfully conduct the long-term research and development program of the 「Development of Core Technologies to Ensure Safety of Spent Nuclear Fuel Storage and Disposal System」. Our program, known as the first multi-ministry program in the nuclear field of Korea, mainly focuses on developing core technologies required for the long-term management of SNF, including those for safe storage and deep geological disposal of SNF. The program comprises three subprograms and seven key projects covering the storage, disposal, and regulatory sectors of SNF management. Our program will last from 2021 through 2029, with a budget of approximately four billion USD sponsored by MSIT, MOTIE, and NSSC.