The effect of solidification rate on micro-segregation in investment casting of IN738LC superalloy was studied. In Ni-based superalloys, the micro-segregation of solute atoms is formed due to limited diffusion during cast and solidification. The microstructure of cast Ni-based superalloys is largely divided into dendrite core of initial solidification and interdendrite of final solidification. In particular, mosaic shaped eutectic γ/γ’ and carbides are formed in the interdendrite of the final solidification region in some cases. The micro-segregation phenomena formed in regions of dendrite core and interdendrite including eutectic γ/γ’ and carbides were analyzed using OM, SEM/EDS and micro Vickers hardness. As a result of analysis, the lack of (Cr, W) and the accumulation of Ti were measured in the eutectic γ/γ’, and the accumulation of (Cr, Mo) and the lack of Ti were measured in the interdendrite between dendrite and eutectic. Carbides formed in interdendritic region were composed of (Ti, W, Mo, C). The segregation applied to each microstructure is mainly due to the formation of γ’ with Ni3(Al,Ti) composition. The Ni accumulation accompanied by Cr depletion, and the Ti accumulated in the eutectic region as a γ’ forming elements. The Mo tends to diffuse out from the dendrite core to the interdendrite, and the W diffuse out from the interdendrite to the dendrite core. Therefore, the accumulation of Mo in the interdendrite and the deficiency of W occur in the eutectic region located in the interdendrite. Heat treatment makes the degree of the micro-segregation decrease due to the diffusion during solid solution. This study could be applied to the heat treatment technology for the micro-segregation control in cast Ni-based superalloys.

Effects of growth variables and post-growth annealing on the optical, structural and electrical properties of magnetron-sputtered Ga0.04Mg0.10Zn0.86O films are characterized in detail. It is observed that films grown from pure oxygen plasma showed high resistivity, ~102 Ω·cm, whereas films grown in Ar plasma showed much lower resistivity, 2.0 × 10− 2 ~ 1.0 × 10−1 Ω·cm. Post-growth annealing significantly improved the electrical resistivity, to 4.3 ~ 9.0 × 10−3 Ω·cm for the vacuum annealed samples and to 1.3 ~ 3.0 × 10−3 Ω·cm for the films annealed in Zn vapor. It is proposed that these phenomena may be attributed to the improved crystalline quality and to changes in the defect chemistry. It is suggested that growth within oxygen environments leads to suppression of oxygen vacancy (Vo) donors and formation of Zn vacancy (VZn) acceptors, resulting in highly resistive films. After annealing treatment, the activation of Ga donors is enhanced, Vo donors are annihilated, and crystalline quality is improved, increasing the electron mobility and the concentration. After annealing in Zn vapor, Zn interstitial donors are introduced, further increasing the electron concentration.

In this study, gas flow pattern and temperature distribution in a laboratory scale low temperature furnace for carbonization were numerically analyzed. The furnace was designed for testing carbonization process of carbon fibers made from polyimide(PI) precursor. Nitrogen gas was used as a working gas and it was treated as an ideal gas. Three-dimensional computational fluid dynamics analysis for steady state turbulent flow was used to analyze flow pattern and temperature field in the furnace. The results showed that more uniform velocity profile and axisymmetric temperature distribution could be obtained by varying mass flow rate at the inlets.

Solar energy is being constantly studied since it can reduce green house gas by adapting cooling and heating system of domestic architecture as a clean energy source. This study confirmed the reliability of experimental apparatus with temperature measurement of each components by developing cooling and heating system which is combined with artificial solar thermal energy using halogen lamp and refrigerator, examined the heat transfer characteristics according to room internal temperature and lamp distance with the materials of emissive plate (acrylic, copper and stainless). As a result of it, We found that the room internal temperature 18℃ was finer than 21℃ and 24℃ in case of heat transfer rate according to each components. Also, copper in the material change of emissive plate was showed finer heat transfer effects than stainless because of high thermal absorptivity when lamp distance was short.

This study sought to investigate the effects of heat-moisture treatment (HMT) and ethanol treatment (EOH) for improving the quality and storage stability of Tteokbokki Tteok. The quality characteristics were evaluated by moisture, pH, color, texture profile analysis, and observing the microbial properties after the heat-moisture treatment or ethanol treatment. As the storage period increased, the moisture content of Tteokbokki Tteok tended to decrease except for the HMT group (p<0.05) while the pH did not show significant variation except for the EOH group (p<0.05). While measuring the color, the L-value tended to increase in all groups during the storage period. The a-value and the b-value showed the highest values in the HMT group and the control (CON) group, respectively. In the texture profile analysis, all groups showed a significant tendency to increase levels of hardness and chewiness as the storage period increased (p<0.05). The HMT group showed an increase in hardness and adhesiveness, which are characteristics of the HMT treatment. The results of examining the microbial properties of Tteokbokki Tteok showed that the total microbial count in the HMT group was 4.52 on the 8th day of storage, which was lower than the level in the CON group and the EOH group on the 4th day of storage. Yeast and mold were not measured during the storage period. Thus the results of this study showed that when manufacturing Tteokbokki Tteok, the heat-moisture treatment of rice powder increased the storage stability by delaying microbial growth and also had positive effects on quality.

본 연구는 효과적인 열전도를위한 거시적 구조 구성과 단위 구조 변화의 동시 설계를 위한 위상 최적화 방법을 제시한다. 거시적 규모의 구조 내에서 위치에 따른 단위 구조의 형태 변화는 거시적 규모뿐만 아니라 미시적 단위의 설계도 가능하며 등방성 단위 구조를 사용하는 것보다 더 나은 성능을 제공할 수 있다. 이 결과로 두 구성을 결합한 기능적으로 등급의 복합 구조가 생성된다. 대표 체적 요소 (RVE) 방법은 형태 변화에 따른 다중 재료 기반 단위 구조의 다양한 열전도 특성을 얻기 위해 적용된다. RVE 분석 결과를 바탕으 로 머신 러닝 기법을 이용하여 특정 형태의 단위 구조물의 물성치를 도출할 수 있다. 거시적 위상 최적화는 기존의 SIMP 방법을 사용하여 수행되며, 거시 구조를 구성하는 단위 구조는 동시 최적화 과정에 따라 열전도 성능을 향상시키기 위한 다양한 형태를 가질 수 있다. 제안된 방법의 효과를 확인하기 위해 열 컴플라이언스 최소화 문제의 수치예가 제공된다.

In this study, a welding heat source model was presented and verified during fiber laser welding. The multi-layered heat source model is a model that can cover most of existing studies and can be defined with a simple formula. It consists of a total of 12 parameters, and an optimization algorithm was used to find them. As optimization algorithms, adaptive simulated annealing, multi island genetic algorithm, and Hooke-Jeeves technique were applied for comparative analysis. The parameters were found by comparing the temperature distribution when the STS304L was bead on plate welding and the temperature distribution derived through finite element analysis, and all three models were able to derive a model with similar trends. However, there was a deviation between parameters, which was attributed to the many variables. It is expected that a more clear welding heat source model can be derived in subsequent studies by giving a guide to the relational expression and range between variables and increasing the temperature measurement point, which is the target value.

In this study, the effect of thermal grease and heat sink material of cooler on CPU temperature was measured and compared with LinX(v0.9.6) and HWMonitor.When the computer is booted without thermal grease applied, the CPU temperature rises rapidly, and the CPU temperature reaches 100℃ after 60 seconds for aluminum heat sink and 140 seconds for copper heat sink. The CPU temperature is lower as the thermal conductivity coefficient of thermal grease is higher, and the CPU temperature is lower when the thermal conductivity coefficient of the cooler is higher. In addition, when using a thermal grease and a heat sink with a high coefficient of thermal conductivity, the cooler rpm can be lowered, which is considered to be advantageous in terms of system stability and energy saving.

Welding is the most widely used technology for manufacturing in the automobile, and shipbuilding industries. Fiber laser welding is rapidly introduced into the field to minimize welding distortion and fast welding speed. Although it is advantageous to use finite element analysis to predict welding distortion and find optimized welding conditions, there are various heat source model for fiber laser welding. In this study, a welding heat source was proposed using a multi-layered heat source model that encompasses most of the existing various welding heat source models: conical shape, curved model, exponential model, conical-cylindrical model, and conical-conical model. A case study was performed through finite element analysis using the radius of each layer and the ratio of heat energy of the layer as variables, and the variables were found by comparing them with the actual experimental results. For case study, by applying Adaptive simulated annealing, one of the global optimization algorithms, we were able to find the heat source model more efficiently.

본 연구는 기상청 현업모델(LDAPS)로부터 예측된 서울의 도시열섬 강도와 지상 기온을 AWS 관측과 비교 평가하였다. 관측된 서울의 열섬 강도는 봄과 겨울동안 증가하며 여름동안 감소한다. 열섬 강도의 시간적 변동 경향은 새벽 시간 최대, 오후에 최소를 보인다. 기상청 국지기상예측시스템(LDAPS)으로부터 예측된 열섬 강도는 여름철 과대모의, 겨울철 과소모의 특징을 보인다. 특히 여름철은 주간에 과대 모의 경향이 증가하며, 겨울은 새벽 시간 과소 모의 오차가 크게 나타난다. LDAPS에서 예측된 지면 기온의 오차는 여름철 감소하며 겨울철 증가한다. 겨울철 열섬 강도의 과소 모의는 도시 기온의 과소 모의와 관련되었으며, 여름철 열섬 강도의 과대 모의는 교외 지역 기온의 과소 모의로부터 기인하는것으로 판단된다. 도시 열섬강도 예측성 개선을 위하여 도시효과를 고려하는 도시캐노피모델을 LDAPS와 결합하여 2017년 여름 기간동안 모의하였다. 도시캐노피모델 적용 후 도시의 지면 기온의 오차는 개선되었다. 특히 오전시간 과소모의되는 기온의 오차 개선 효과가 뚜렷하였다. 도시캐노피모델은 여름동안 과대 모의하는 도시열섬강도를 약화시키는 개선 효과를 보였다.

In this study, AlSi10Mg powders with average diameters of 44 μm are additively manufactured into bulk samples using a selective laser melting (SLM) process. Post-heat treatment to reduce residual stress in the as-synthesized sample is performed at different temperatures. From the results of a tensile test, as the heat-treatment temperature increases from 270 to 320oC, strength decreases while elongation significantly increases up to 13% at 320oC. The microstructures and tensile properties of the two heat-treated samples at 290 and 320oC, respectively, are characterized and compared to those of the as-synthesized samples. Interestingly, the Si-rich phases that network in the as-synthesized state are discontinuously separated, and the size of the particle-shaped Si phases becomes large and spherical as the heat-treatment temperature increases. Due to these morphological changes of Si-rich phases, the reduction in tensile strengths and increase in elongations, respectively, can be obtained by the post-heat treatment process. These results provide fundamental information for the practical applications of AlSi10Mg parts fabricated by SLM.

In this study, the cooling performance of the motor was analyzed according to the number and the length of the fins of the heat sink, and at the same time, the effect of forced convection on the cooling performance improvement by changing the air flow speed of the cooling fan was conducted. In order to find out the cooling performance in terms of turbulent kinetic energy, pressure, and temperature according to the number of heat sink fins, length of fins, and wind speed of the cooling fan, an aluminum heat sink was modeled according to the size of the motor. The heating value of the motor was calculated, and it was set to be the same under all analysis conditions. The turbulence model applied for numerical analysis in this study used the standard k-ε model. As a result, it was confirmed that the cooling effect of the heat sink increases as the air flow speed of the cooling fan, the number of fins, and the length of fins increase.

Martensitic stainless steel is commonly used in the medical implant instrument. The alloy has drawbacks in terms of strength and wear properties when applied to instruments with sharp parts. 440C STS alloy, with improved durability, is an alternative to replace 420 J2 STS. In the present study, the carbide precipitation, and mechanical and corrosion properties of STS 440C alloy are studied as a function of different heat treatments. The STS 440C alloy is first austenitized at different temperatures; this is immediately followed by oil quenching and sub-zero treatment. After sub-zero treatment, the alloy is tempered at low temperatures. The microstructures of the heat treated STS 440C alloy consist of martensite and retained austenite and carbides. Using EDX and SADP with a TEM, the precipitated carbides are identified as a Cr23C6 carbide with a size of 1 to 2 μm. The hardness of STS 440C alloy is improved by austenitization at 1,100 oC with sub-zero treatment and tempering at 200 oC. The values of Ecorr and Icorr for STS 440C increase with austenitization temperature. Results can be explained by the dissolution of Cr-carbide and the increase in the retained austenite. Sub-zero treatment followed by tempering shows a little difference in the properties of potentiodynamic polarizations.

To understand the role of small heat shock protein (sHSPs) in rice plant response to various stresses such as the heat and oxidative stresses, a cDNA encoding a 24.1 kDa mitochondrial small HSP (Oshsp24.1) was isolated from rice by rapid amplification of cDNA ends (RACE) PCR. The deduced amino acid sequence shows very high similarity with other plant small HSPs. DNA gel blot analysis suggests that the rice genome contains more than one copy of Oshsp24.1. High level of expression of Oshsp24.1 transcript was observed in rice seedlings in response to heat, methyl viologen, hydrogen peroxide, ozone, salt and heavy metal stresses. Recombinant OsHSP24.1 protein was produced in E. coli cells for biochemical assay. The protein formed oligomeric complex when incubated with Sulfo-EGS (ethylene glycol bis (succinimidyl succinate)). Our results shows that Oshsp24.1 has an important role in abiotic stress response and have potential for developing stress-tolerant plants.

Heat shock proteins (HSPs) are highly conserved cellular proteins that contribute to adaptive responses of organisms to a variety of stressors. In response to stressors, cellular levels of HSPs are increased and play critical roles in protein stability, folding and molecular trafficking. The mRNA expression pattern of two well-known heat shock protein transcripts, HSP70 and HSP90 were studied in two tissues of nerve ganglia, cerebral ganglion and pleuropedal ganglion of Pacific abalone (Haliotis discus hannai). It was observed that both HSP70 and HSP90 transcripts were upregulated under heat stress in both ganglion tissues. Expression level of HSP70 was found higher than HSP90 in both ganglia whereas cerebral ganglion showed higher expression than pleuropedal ganglion. The HSP70 and HSP90 showed higher expression at Day-1 after exposed to heat stress, later decreased at Day-3 and Day-7 onwards. The present result suggested that HSP70 and HSP90 synthesize in nerve ganglion tissues and may provide efficient protection from stress.

PURPOSES : This study aims to determine the type (e.g., melting point, freezing point, latent heat fusion) and optimal content of phase change material (PCM) based on the numerical and experimental analyses evaluating the effects of heat transfer in PCM-modified asphalt pavement systems. METHODS : The effect of PCM on the thermophysical properties of PCM-modified asphalt concrete can be taken as an effective volumetric heat capacity. The volumetric fraction of PCM was calculated using an iterative method. The numerical model was established and computed using the MATLAB 2020 software. The optimum PCM design tool was developed to select the type and contents of the PCM. The PCM was chosen based on the following criteria: black-ice-formation delay time, minimize temperature increase, and increase temperature area. To validate the numerical model, asphalt mixtures were modified with varying PCM contents, and the temperature response of the PCMmodified asphalt samples was examined via temperature test. RESULTS : The numerical results showed that incorporating PCM into the asphalt mixture can slow the cooling rate of the pavement system. The predicted results from the optimum PCM design tool were highly consistent with the measured values from the laboratory temperature test. CONCLUSIONS : The temperature of PCM-modified asphalt pavement can be predicted via numerical method. The effect of PCM on the thermophysical properties can be considered as effective volumetric heat capacity; while the volume fraction of PCM can be calculated via an iterative method. The accuracy of the numerical model was confirmed by a high agreement between the measured and predicted values.

This paper reports critical heat flux(CHF) performance on wire heater according to material, thickness, length, cross sectional shape. Water was employed as the working fluid, which was saturated at 1 atm. By comparison of CHF values with difference conditions of wire length, contact resistance inherent in the experimental apparatus could be analyzed, which had made the bias error in many research groups. So, exact value of CHF could be measured, which was consistent with the literatures. The CHF value showed decrease tendency, as the cross sectional area increased and reach to the capillary length of the working fluid. Meanwhile, the effect of thermal properties on CHF was not observed in the experimental cases. This data would be used as a reference data in research field of CHF using wire heater, i.e. reactivity initiative accident(RIA).