오존은 수돗물 정수장에서 이용되는 소독 물질로 미세오염 물질들을 비롯해서 박테리아나 병원성 미생물체를 효과적으로 제거하는 것으로 많은 연구가 보고되어 있다. 본 연 구에서는 실내 사육 중인 붉은 체색을 지닌 Glyptotendipes tokunagai를 대상으로 서로 다른 농도의 오존 노출에 따른 영향을 파악하기 위해 치사율, 체색 변화와 heat shock protein 70 (HSP70) 유전자 발현을 측정하였다. 오존에 노출 된 G. tokunagai에서 농도-시간 의존적으로 치사율 증가가 관찰되었다. 또한 체색 변화는 오존 농도에 따라 붉은색의 체색이 체절마다 엷어지며 탈색되고 경직되는 현상이 보였다. HSP70 유전자 발현은 저농도인 0.2~0.5 ppm에서 노출 10분과 20분에 유의한 수준으로 높게 나타났으나 (P<0.05), 30 분 노출 후에는 발현량이 감소하는 경향을 보였다. 생리적으로 저산소층에 대해 적응능력이 뛰어난 깔따구 경우에도 오존은 매우 강력한 치사 효과를 유발하여 30분 노출 후 경직과 헤모글로빈 파괴로 인한 탈색이 유발되는 것을 보여주었다. 따라서 본 결과는 수돗물 정수장에서 병원성 미생물을 제거하는 데 사용되는 오존이 수생물에 주는 영향성을 파악하는 기초자료로서 활용될 수 있을 것이다.

에너지를 절감하기 위해 고효율 히트펌프를 개발하기 위한 많은 연구가 이루어지고 있으며, 실외기 코일에 발생하는 서리가 발생하는 현상을 줄이거나 없애기 위한 연구도 동시에 이루어지고 있다. 계절에 관계없이 히트펌프의 실외기에 서리가 발생하지 않는 연구를 진행할 수 있도록 자연상태와 동일한 조건에서 실험할 수 있는 항온챔버를 구축하였다. 실험장치의 타당성을 검증하기 위해 실험장치인 항온챔버 내의 실외기 앞 덕트의 직선 길이를 3가지 조건으로 나누어 시뮬레이션 하였다. 그 결과 덕트 관경의 10배 길이만큼 직선 공간을 확보해야 한다는 것을 알게 되었다.

Microstructural characteristics of directionally solidified René 80 superalloy are investigated with optical microscope and scanning electron microscope; solidification velocity is found to change from 25 to 200 μm/s under the condition of constant thermal gradient (G) and constant alloy composition (Co). Based on differential scanning calorimetry (DSC) measurement, γ phase (1,322 oC), MC carbide (1,278 oC), γ/γ' eutectic phase (1,202 oC), and γ' precipitate (1,136 oC) are formed sequentially during cooling process. The size of the MC carbide and γ/γ' eutectic phases gradually decrease with increasing solidification velocity, whereas the area fractions of MC carbide and γ/γ' eutectic phase are nearly constant as a function of solidification velocity. It is estimated that the area fractions of MC carbide and γ/γ' eutectic phase are determined not by the solidification velocity but by the alloy composition. Microstructural characteristics of René 80 superalloy after solid solution heat-treatment and primary aging heat-treatment are such that the size and the area fraction of γ' precipitate are nearly constant with solidification velocity and the area fraction of γ/γ' eutectic phase decreases from 1.7 % to 0.955 %, which is also constant regardless of the solidification velocity. However, the size of carbide solely decreases with increasing solidification velocity, which influences the tensile properties at room temperature.

Experiments were conducted to evaluate the performance factors such as type of working fluid, flow direction, arrangement and stage of loop thermosyphon heat exchanger for ESS battery container cooling. Pentane showed slightly better performance of the heat exchanger than R-134a as a working fluid. Driving the fan in the suction direction showed improved performance compared to the blowing direction. The two-stage heat exchanger increased the heat transfer rate by more than 30% at the same temperature difference compared to the single-stage heat exchanger. Also, the counterflow flow showed better performance than the parallel flow in the two-stage heat exchanger.

The temperature distributions were numerically calculated for the two-dimensional transient conduction heat transfer problem of a square plate. The obtained temperature distributions were converted into colors to create images, and they were provided as learning and test data of CNN. Classification and regression networks were constructed to predict representative wall temperatures through CNN analysis. As results, the classification networks predicted the representative wall temperatures with an accuracy of 99.91% by erroneously predicting only 1 out of 1100 images. The regression networks predicted the representative wall temperatures within errors of C. From this fact, it was confirmed that the deep learning techniques are applicable to the transient conduction heat transfer problems.

AZO thin films are grown on a p-Si(111) substrate by RF magnetron sputtering. The characteristics of various thicknesses and heat treatment conditions are investigated by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Hall effect and room-temperature photoluminescence (PL) measurements. The substrate temperature and the RF power during growth are kept constant at 400 ℃ and 200 W, respectively. AZO films are grown with a preferred orientation along the c-axis. As the thickness and the heat treatment temperature increases, the length of the c-axis decreases as Al3+ ions of relatively small ion radius are substituted for Zn2+ ions. At room temperature, the PL spectrum is separated into an NBE emission peak around 3.2 eV and a violet regions peak around 2.95 eV with increasing thickness, and the PL emission peak of 300 nm is red-shifted with increasing annealing temperature. In the XPS measurement, the peak intensity of Al2p and Oll increases with increasing annealing temperature. The AZO thin film of 100 nm thickness shows values of 6.5 × 1019 cm−3 of carrier concentration, 8.4 cm−2/V·s of mobility and 1.2 × 10−2 Ω·cm electrical resistivity. As the thickness of the thin film increases, the carrier concentration and the mobility increase, resulting in the decrease of resistivity. With the carrier concentration, mobility decreases when the heat treatment temperature increases more than 500 ℃.

The occurrence of exotic weeds and their influx into farmlands due to climate change poses many problems. Therefore, it is necessary to generate a prediction model for the occurrence pattern of these exotic weeds based on scientific evidence and devise prevention measures. The photosynthetic apparatus is known as the most temperaturesensitive component of a plant cell and its initial response to temperature stress is to inhibit the activation of photosystem II. This study investigated the potential of OJIP transients in assessing temperature stress in exotic weeds. The four exotic weeds currently flowing into Korean farmlands include Amaranthus spinosus, Conyza bonariensis, Crassocephalum crepidioides, and Amaranthus viridis. These weeds were treated at 5°C, 10°C, 15°C, 20°C, 25°C, 30°C, 35°C, and 40°C and the OJIP curves and JIP parameters were measured and analyzed. The results showed that heat and chilling stress affected the photosystem II (PSII) electron transport of A. spinosus, whereas C. crepidioides and A. viridis were more affected by high-temperature stress than by low-temperature stress. Lastly, C. bonariensis showed resistance to both high and low-temperature stress. The results of this study suggest that OJIP transients and JIP parameters can be used to analyze damage to the photosynthetic apparatus by temperature stress and that they can serve as sensitive indicators for the occurrence pattern of exotic weeds.

For surface hardening of a continuous casting mold component, a fundamental metallurgical investigation on dissimilar laser clads (Cu–NiCrBSi) is performed. In particular, variation behavior of microstructures and mechanical properties (hardness and wear resistance) of dissimilar clads during long-term service is clarified by performing high-temperature postclad heat treatment (temperature range: 500 ~ 1,000 ℃ and isothermal holding time: 20 ~ 500 min). The microstructures of clad metals (as-clads) consist of fine dendrite morphologies and severe microsegregations of the alloying elements (Cr and Si); substrate material (Cu) is clearly confirmed. During the post-clad heat treatment, the microsegregations are totally homogenized, and secondary phases (Cr-based borides and carbides) precipitated during the short-term heat treatment are also almost dissolved, especially at the heat treatment conditions of 950 ℃ for 500 min. Owing to these microstructural homogenization behaviors, an opposite tendency of the surface mechanical properties can be confirmed. In other words, the wear resistance (wear rate) improves from 4.1 × 10−2 mm3/Nm (as-clad condition) to 1.4 × 10-2 mm3/Nm (heat-treated at 950 ℃ for 500 min), whereas the hardness decreases from 453 HV (as-clad condition) to 142 HV (heat-treated at 950 ℃ for 500 min).

본 연구는 농촌진흥청 국립원예특작과학원 채소과에서 육성 중인 고추 34계통과 세계채소센터 육성 계통과 자원 12점 등 총 46점의 고추를 공시하여, 종자의 발아율, 수량 및 상품과율, 그리고 화분발아율을 조사하여 내서성이 강한 고추 자원을 선발하기 위하여 수행되었다. 1. 종자발아율 비교에서 여름종자는 가을종자 대비 상대적인 피해율은 4.3~100% 범위였고, H42(1.6%), H16(5.0%), H14(6.3%), H02(12.4%), H44(13.7%), H12(15.9%), H03 (17.6%), H17(23.4%) 순으로 대조 계통인 H37(26.2%)에 비해 피해율이 낮았다. 2. 고추 과실의 수량은 34.4~446.5g, 총 과실수는 2.0~134.3 개를 나타냈다. 상품과 비율에 있어서 75% 이상은 H22(95.0%), H16(89.1%), H37(88.4%), H40(86.4%), H6 (86.0), H27(83.7%), H04(83.6%), H03(82.6%), H08(81.1%), H44(81.4%), H02(80.0%), H45(79.1%), H17(78.7%), H19 (77.7%), H34(77.0%), H15(76.9%), H42(76.3%) 순으로 나타 났다. 3. 고온 처리에 의한 화분발아율의 피해율은 H06(59.5%), H14(74.4%), H44(85.3%), H03(90.2%)가 대조구인 H37 (94.7%)과 나머지 다른 고추에 비해 상대적으로 낮았다. 이상의 결과, 가을종자 대비 여름종자 종자발아율의 피해율, 수량 및 상품과율, 그리고 고온 처리에 의한 화분발아율 등을 고려하여, H03, H04, H06, H14, H17, H22, H44, H45 계 통을 내서성이 높은 자원으로 선발하였다.

In this paper, the heat transfer performance of nanofluids is predicted by numerical analysis methods. The nanoparticles used in this study is SiO2, with concentrations of 1, 2, 3vol.%, and the base fluid is water. Reynolds number of nanofluids ranges from 10,000 to 50,000. A numerical study on the heat transfer characteristics of nanofluid was conducted using a single-phase model. The temperature of the fluid entering from the inlet of the tube is 293.15K. A constant heat flux of 31,650W/m2 was applied at the wall, and the thickness of the wall was ignored. Heat transfer coefficients, thermal conductivity and Nusselt number were selected as indicators for comparing heat transfer performance of nanofluids. As the nanofluid concentration increases, the temperature and velocity distribution by the cross section of the coil tube and straight tube increased. As the Reynolds number increases, temperature difference between inner direction and outer direction reduced in coil tube. For straight tube, the temperature difference between the wall and the center of the tube also decreased.

While the vehicle has a wide front view, making it easy to recognize obstacles while driving, the rear side has a narrow view and the inconvenience of having to turn its head to check. A side mirror developed to address this discomfort is mounted outside the front door of a passenger car and used to identify rear objects. In this study, heat transfer analysis was performed and analyzed in order to obtain optimal defrost conditions using regression analysis method for removing mirror condensation and frost. As a result of this study, the coefficient of determination, R2, which represents the regression to the total variation through regression analysis, showed a good reliability of 85.3%. Comparing the predicted and interpreted values of the maximum temperature distribution in the regression equation established in this study, it was included in the 95% confidence interval, enabling the prediction of the maximum temperature distribution over the heat conduction time.

The estimation of heat source model is very important for heat transfer analysis with finite element method. Part I of this study used adaptive simulated annealing which is one of the global optimization algorithm for anticipating the parameters of the Goldak model. Although the analysis with 3D model which depicted the real situation produced the correct answer, that took too much time with moving heat source model based on Fortran and Abaqus. This research suggests the procedure which can reduce time with maintaining quality of analysis. The lead time with 2D model is reduced by 90% comparing that of 3D model, the temperature distribution is similar to each other. That is based on the saturation of heat transfer among the direction of heat source movement. Adaptive simulated annealing with 2D model can be used to estimate more proper heat source model and which could enhance to reduce the resources and time for experiments.

선박 및 해양구조물에서 사용하고 있는 고강도 알루미늄 합금들은 스틸과 비교해서 많은 이점을 가지고 있다. 최근 고강도 알루미늄 합금들은 육상 및 해양에 폭넓게 사용되고 있으며, 특히, 특수목적 선박의 선체 외판구조에 많이 이용되고 있고, 교량 구조물에 사용되는 상자 구조물, 그리고 고정식 해양플랫폼의 상부구조에서 소비율이 증가하고 있다. 알루미늄 재료는 스틸보다 1/3의 중량 구성비를 통하여, 구성 중량을 줄이게 하여 연비 절감을 가능하게 한다. 일반적인 강구조물의 응력-변형률 관계와 비교하면, 용접가공에 따라 발생하는 열영향부의 존재로 인하여 상당히 다르게 나타난다. 왜냐하면, 강구조물과 비교하면 열전도율이 높아서, 열영향부(heat affected zone, HAZ)가 남아 있어 구조 강도 저하를 가져온다. 본 논문에서는 MIG(Metal inert gas) 용접 때문에 발생하는 열영향부를 고려하고, 종방향 압축 하중에 대한 알루미늄 보강판의 좌굴 및 최종강도 특성을 분석하였다. MIG 용접에 따른 열영향부를 고려한 경우, 좌굴 및 최종강도 모두 감소하며, 열영향부의 범위가 15 mm부터 항복 이후 에너지 소실률이 크게 나타나며, 25 mm 이상부터는 그 차이가 크지 않다. 따라서, 알루미늄 합금재료를 적용한 보강판의 구조 거동을 파악하기 위해서는 열영향부 영향에 대한 검토 및 분석이 중요하다.

The relationship between the precipitation of secondary phase and the thermal properties of Al-4.5%Cu alloy (in wt.%) after various heat treatments has been studied. Solid solution treatment of alloy was performed at 808 K for 6 hours, followed by warm water quenching; then, the samples were aged in air at 473 K for different times. The thermal diffusivity of the Al-4.5%Cu alloy changed with the heat treatment conditions of the alloy at temperatures below 523 K. The as-quenched specimen had the lowest thermal diffusivity, and as the artificial aging time increased, the thermal diffusivity of the specimen increased in the temperature range between 298 and 523 K. For the specimen aged for five hours, the thermal conductivity was 12% higher than that of the as-quenched specimens at 298 K. It is confirmed that the thermal diffusivity and thermal conductivity of the Al-4.5%Cu alloy significantly depend on their thermal history at temperatures below 523 K. The precipitation and dissolution of the Al2Cu phase were confirmed via DSC for the alloys, and the formation of coefficient of thermal expansion peaks in TMA was caused by precipitation. The precipitation of supersaturated solid solution of Al-4.5%Cu alloys had an additional linear expansion of ≈ 0.05 % at 643 K during thermal expansion measurement.