The electrochemical performances of an asymmetric hybrid capacitor were investigated using LiFePO4 as the positive electrode and active carbon fibers(ACF) as the negative electrode. The electrochemical behaviors of a nonaqueous hybrid capacitor were characterized by constant current charge/discharge test. The specific capacitance using LiFePO4/ACF electrode turned out to be 0.87F/cm2 and the unit cell showed excellent cycling performance. This hybrid capacitor was able to deliver a specific energy as high as 178 Wh/kg at a specific power of 1,068 W/kg.

The power capacitors used as vehicle inverters must have a small size, high capacitance, high voltage, fast response and wide operating temperature. Our thin film capacitor was fabricated by alumina layers as a dielectric material and a metal electrode instead of a liquid electrolyte in an aluminum electrolytic capacitor. We analyzed the micro structures and the electrical properties of the thin film capacitors fabricated by nano-channel alumina and metal electrodes. The metal electrode was filled into the alumina nano-channel by electroless nickel plating with polyethylene glycol and a palladium catalyst. The spherical metals were formed inside the alumina nano pores. The breakdown voltage and leakage current increased by the chemical reaction of the alumina layer and PdCl2 solution. The thickness of the electroless plated nickel layer was 300 nm. We observed the nano pores in the interface between the alumina layer and the metal electrode. The alumina capacitors with nickel electrodes had a capacitance density of 100 nF/cm2, dielectric loss of 0.01, breakdown voltage of 0.7MV/cm and leakage current of 104μA.

We have investigated the structural and electrical properties of Ga-doped ZnO (GZO) thin films deposited by anRF magnetron sputtering at various RF powers from 50 to 90W. All the GZO thin films are grown as a hexagonal wurtzitephase with highly c-axis preferred parameters. The structural and electrical properties are strongly related to the RF power. Thegrain size increases as the RF power increases since the columnar growth of GZO thin film is enhanced at an elevated RFpower. This result means that the crystallinity of GZO is improved as the RF power increases. The resistivity of GZO rapidlydecreases as the RF power increases up to 70W and saturates to 90W. In contrast, the electron concentration of GZO increasesas the RF power increases up to 70W and saturates to 90W. GZO thin film shows the lowest resistivity of 2.2×10−4Ωcmand the highest electron concentration of 1.7×1021cm−3 at 90W. The mobility of GZO increases as the RF power increasessince the grain boundary scattering decreases due to the reduced density of the grain boundary at a high RF power. Thetransmittance of GZO thin films in the visible range is above 90%. GZO is a feasible transparent electrode for application asa transparent electrode for thin film solar cells.

We have investigated the structural and optical properties of Ga-doped ZnO (GZO) thin films deposited by RFmagnetron sputtering at various deposition temperatures from 100 to 500oC. All the GZO thin films are grown as a hexagonalwurtzite phase with highly c-axis preferred parameter. The structural and electrical properties are strongly related to depositiontemperature. The grain size increases with the increasing deposition temperature up to 400oC and then decreases at 500oC. Thedependence of grain size on the deposition temperature results from the variation of thermal activation energy. The resistivityof GZO thin film decreases with the increasing deposition temperature up to 300oC and then decreases up to 500oC. GZO thinfilm shows the lowest resistivity of 4.3×10−4Ωcm and highest electron concentration of 1.0×1021cm−3 at 300oC. The mobilityof GZO thin films increases with the increasing deposition temperature up to 400oC and then decreases at 500oC. GZO thinfilm shows the highest resistivity of 14.1cm2/Vs. The transmittance of GZO thin films in the visible range is above 87% atall the deposition temperatures. GZO is a feasible transparent electrode for the application to the transparent electrode of thinfilm solar cells.

The hybrid structured photo-electrode for dye-sensitized solar cells was fabricated based on the composites of nanoparticles and nanowires. Three samples with different hybrid structures were prepared with 17 vol%, 43 vol%, and 100 vol% nanowires. The energy conversion efficiency was enhanced from 5.54% for pure nanoparticle cells to 6.01% for the hybrid structure with 17 vol% nanowires. For the hybrid structured layers with high nanowires concentration (43 vol% and 100 vol%), the efficiency decreased with the nanowire concentration, because of the decrease of specific surface area, and of thus decreased current density. The random orientations of nanowires can be preserved by the doctor blade process, resulted in the enhanced efficiency. The hybrid structured layer can possess the advantages of the high surface area of nanoparticles and the rapid electron transport rate and the light scattering effect of nanowires.

A porous nickel-tin nano-dendritic electrode, for use as the anode in a rechargeable lithium battery, has been prepared by using an electrochemical deposition process. The adjustment of the complexing agent content in the deposition bath enabled the nickel-tin alloys to have specific stoichiometries while the amount of acid, as a dynamic template for micro-porous structure, was limited to a certain amount to prevent its undesirable side reaction with the complexing agent. The ratios of nickel to tin in the electro-deposits were nearly identical to the ratios of nickel ion to tin ion in the deposition bath; the particle changed from spherical to dendritic shape according to the tin content in the deposits. The nickel to tin ratio and the dendritic structure were quite uniform throughout the thickness of the deposits. The resulting nickel-tin alloy was reversibly lithiated and delithiated as an anode in rechargeable lithium battery. Furthermore, the resulting anode showed much more stable cycling performance up to 50 cycles, as compared to that resulting from dense electro-deposit with the same atomic composition and from tin electrodeposit with a similar porous structure. From the results, it is expected that highly-porous nickel-tin alloys presented in this work could provide a promising option for the high performance anode materials for rechargeable lithium batteries.

Mo thin films were used for the back electrode because of the low resistivity in the Mo/CuInGaSe2 contact inchalcopyrite solar cells. 1µm thick Mo thin films were deposited on soda lime glass by varying the Ar pressure with the dc-magnetron sputtering process. The effects of the Ar pressure on the morphology of the Mo back electrode were studied andthe relationships between the morphology and electro-optical properties, namely, the resistivity as well as the reflectance of theMo thin films, were investigated. The resitivity increased from 24µΩ·cm to 11833µΩ·cm; this was caused by the increasedsurface defect and low crystallinity as the Ar pressure increased from 3×10−3 to 3×10−2Torr. The surface morphologies ofthe Mo thin films changed from somewhat coarse fibrous structures to irregular and fine celled strucutures with increased surfacecracks along the cell boundaries, as the Ar pressure increased from 3×10−3 to 3×10−2Torr. The changes of reflectances in thevisible light range with Ar pressures were mainly attributed to the surface morphological changes of the Mo thin films. Thereflectance in the visible light range showed the highest value of 45% at 3×10−3Torr and decreased to 18.5% at 3×10−2Torr.

In this paper, the effect of electrical characteristics and electrode shape on the alignment and attachment of multi-walled carbon nanotubes (MWNTs) has been studied. The attraction and alignment of MWNTs between the gaps has been investigated by applying electric field which is called electrophoresis and dielectrophoresis. According to the frequency of electric field, positive or negative dielectrophoretic force can be determined. The concentration of MWNTs solution was , and a droplet of was dropped between two electrodes. Through the repeated experiments, the optimal electrical conditions for aligning and attaching MWNTs in the desired places were obtained. Since the frequency range of 100 kHz~10 MHz generated positive dielectrophoretic force, MWNTs were attracted and aligned between the gaps with this frequency range. For generating enough force to attract MWNTs, the appropriate voltage range was . Furthermore, the effect of electrode shape on the alignment of MWNTs was investigated. A single MWNT attachment was accomplished on the round shaped with 70% yield.

Chromium nitride (CrN) samples with two different layer structures (multilayer and single layer) were coated on bipolar plates of polymer electrolyte membrane fuel cells (PEMFC) using the reactive sputtering method. The effects with respect to layer structure on corrosion resistance and overall cell performance were investigated. A continuous and thin chromium nitride layer (Cr0.48 N0.52) was formed on the surface of the SUS 316L when the nitrogen flow rate was 10 sccm. The electrochemical stability of the coated layers was examined using the potentiodynamic and potentiostatic methods in the simulated corrosive circumstances of the PEMFC under 80˚C. Interfacial contact resistance (ICR) between the CrN coated sample and the gas diffusion layer was measured by using Wang's method. A single cell performance test was also conducted. The test results showed that CrN coated SUS316L with multilayer structure had excellent corrosion resistance compared to single layer structures and single cell performance results with 25 cm2 in effective area also showed the same tendency. The difference of the electrochemical properties between the single and multilayer samples was attributed to the Cr interlayer layer, which improved the corrosion resistance. Because the coating layer was damaged by pinholes, the Cr layer prevented the penetration of corrosive media into the substrate. Therefore, the CrN with a multilayer structure is an effective coating method to increase the corrosion resistance and to decrease the ICR for metallic bipolar plates in PEMFC.

This study was performed to investigate the effects of Needle Electrode Electrical Stimulation(NEES) on ischemia-induced cere˗ brovascular accidents. After obstruction and reperfusion of arteries in white mice, the amounts of necrosis and inflammation related sub˗ stances Bax, IL-6, Caspase-3, and COX-2 were measured in neurons of the fore-brain. The following results were obtained. This study used 21 male specific pathogen free(SPF) SD rats, 8 weeks of age and approximately 300g in weight. Each exposed artery was completely occluded with non-absorbent suture thread and kept in that state for 5 minutes. The sutures were then removed to allow reperfusion of blood. Test group is control group(common carotid artery occlusion models), a GI(underwent common carotid artery occlusion), and NEES(underwent NEES after artery occlusion). The GI and NEES groups were given 12, 24, or 48 hours of reperfusion before NEES. NEES device(PG6, ITO, Japan, 9V, current, 2Hz) was used to stimulate the bilateral acupoint ST36 of the SD rats for 30 minutes while they were sedated with 3% isoflurane. An immuno-his˗ tochemistry test was done on the forebrains of the GI induced rats. Both Bax and Caspase-3 immuno-reactive cells, related to apoptosis, were greater in the GI than the NEES group. Cox-2 and IL-6 immuno-reactive cells, related to inflammation, were greater in the GI and NEES groups than the control group. We can expect that applying NEES after ischemic CVA is effective for preventing brain cells from being destroyed. And we can conclude NEES should be applyed on early stage of ischemic CVA.

Transparent conductive films of single wall carbon nanotube (SWCNT) were prepared by spray coating method. The effect of acid treatment on the SWCNT films was investigated. The field emission scanning electron microscope (FESEM) shows that acid treatment can remove dispersing agent. The electrical and optical properties of acid-treated films were enhanced compared with those of as deposited SWCNT films. Nitric acid (HNO3), sulfuric acid (H2SO4), nitric acid:sulfuric acid (3:1) were used for post treatment. Although all solutions reduced sheet resistance of CNT films, nitric acid can improve electrical characteristics efficiently. During acid treatment, transmittance was increased continuously with time. But the sheet resistance was decreased for the first 20 minutes and then increased again. Post-treated SWCNT films were transparent (85%) in the visible range with sheet resistance of about 162Ω/sq. In this paper we discuss simple fabrication, which is suitable for different types of large-scale substrates and simple processes to improve properties of SWCNT films.

A Si-CuO-graphite composite was prepared by a mechanical alloying (MA) method. The Si-CuO composite has a mixture structure, where CuO is homogeneously dispersed in Si. Also, and phases were formed during MA and heat treatment. Graphite with the Si-CuO composite was mixed in the same mill for 30 minutes with weight ratio of Si-CuO composite and graphite as 1:1. The Si-CuO composite was homogeneously covered with graphite. SiC phase was not formed. Electrochemical tests of the composite have been investigated, and the first charge and discharge capacities of the material were about 870mAh/g and 660mAh/g, respectively. Those values are about 76% of the first cycle efficiency. The cycle life of the composite showed that the initial discharge capacity of 660 mAh/g could be maintained up to 92% after 20 cycles.

Activated carbon (AC) with very large surface area has high capacitance per weight. However, such activation methods tend to suffer from low yields, below 50%, and are low in electrode density and capacitance per volume. Carbon NanoFibers (CNFs) had high surface area polarizability, high electrical conductivity and chemical stability, as well as extremely high mechanical strength and modulus, which make them an important material for electrochemical capacitors. The electrochemical properties of immobilized CNF electrodes were studied for use as in electrical double layer capacitor (EDLC) applications. Immobilized CNFs on Ni foam grown by thermal chemical vapor deposition (CVD) were successfully fabricated. CNFs had a uniform diameter range from 50 to 60 nm. Surface area was 56 m2/g. CNF electrodes were compared with AC and multi wall carbon nanotube (MWNT) electrodes. The electrochemical performance of the various electrodes was examined with aqueous electrolyte of 2M KOH. Equivalent series resistance (ESR) of the CNF electrodes was lower than that of AC and MWNT electrodes. The specific capacitance of 47.5 F/g of the CNF electrodes was achieved with discharge current density of 1 mA/cm2.

Changes in the surface morphology and light scattering of textured Al doped ZnO thin films on glasssubstrates prepared by rf magnetron sputtering were investigated. As-deposited ZnO:Al films show a hightransmittance of above 80% in the visible range and a low electrical resistivity of 4.5×10-4Ω·cm. The surfacemorphology of textured ZnO:Al films are closely dependent on the deposition parameters of heater temperature,working pressure, and etching time in the etching process. The optimized surface morphology with a cratershape is obtained at a heater temperature of 350oC, working pressure of 0.5 mtorr, and etching time of 45seconds. The optical properties of light transmittance, haze, and angular distribution function (ADF) aresignificantly affected by the resulting surface morphologies of textured films. The film surfaces, havinguniformly size-distributed craters, represent good light scattering properties of high haze and ADF values.Compared with commercial Asahi U (SnO2:F) substrates, the suitability of textured ZnO:Al films as frontelectrode material for amorphous silicon thin film solar cells is also estimated with respect to electrical andoptical properties.

The electrocatalytic behavior of the PtCo catalyst supported on the multi-walled carbon nanotubes (MWNTs) has been evaluated and compared with commercial Pt/C catalyst in a polymer electrolyte membrane fuel cell(PEMFC). A PtCo/MWNTs electrocatalyst with a Pt:Co atomic ratio of 79:21 was synthesized and applied to a cathode of PEMFC. The structure and morphology of the synthesized PtCo/MWNTs electrocatalysts were characterized by X-ray diffraction and transmission electron microscopy. As a result of the X-ray studies, the crystal structure of a PtCo particle was determined to be a face-centered cubic(FCC) that was the same as the platinum structure. The particle size of PtCo in PtCo/MWNTs and Pt in Pt/C were 2.0 nm and 2.7 nm, respectively, which were calculated by Scherrer's formula from X-ray diffraction data. As a result we concluded that the specific surface activity of PtCo/MWNTs is superior to Pt/C's activity because of its smaller particle size. From the electrochemical impedance measurement, the membrane electrode assembly(MEA) fabricated with PtCo/MWNTs showed smaller anodic and cathodic activation losses than the MEA with Pt/C, although ohmic loss was the same as Pt/C. Finally, from the evaluation of cyclic voltammetry(CV), the unit cell using PtCo/MWNTs as the cathode electrocatalyst showed slightly higher fuel cell performance than the cell with a commercial Pt/C electrocatalyst.

TFT-LCD is the most popular type of flat display panel in the information technology field. The back light unit is a main part of the structure of a TFT-LCD panel. Occasionally, studies have shown that failures of the CCFL of the BLU occur due to the poor weld characteristics of these materials. The aim of this study was to prepare some technical data and to characterize a microjoined electrode for the CCFL. Microstructure examinations, microhardness measurements, resistance measurements and microtensile tests of the microjoined electrode were carried out. The result indicates that a large amount of grain coarsening exists in the heat-affected zone (HAZ) of the weld between the cup and the pin. This grain coarsening of the HAZ between the cup and pin is caused by the welding cycle, which may have an influence on the lowest microhardness values. Fracturing of the microjoined electrode also occurred at the HAZ close to the cup between the weld holding the cup and the pin. Additionally, no specific changes of the electrical resistance among the cup, pin, and lead wire themselves or in the microjoined electrode were observed.

This study investigates Bi2O3-B2O3-BaO-ZnO glass with variations of the Co3O4 content (0.25,0.5,1,and 2wt%) and the interaction between transparent dielectric and Ag electrodes heat-treated at 500-560oC for30min. The glass transition temperature, softening temperature and thermal expansion coefficient were432oC, 460oC and 81.4×10-7/oC, respectively. The transmittance of 0.25wt% Co3O4 to which dielectric wasadded was highest and was decreased due to coloration with the addition of more than 0.25wt%. However,without Co3O4, the transmittance of the transparent layer was decreased due to the formation of Ba5Bi3;however, the occurrence of the crystal phase decreased as a result of the addition of Co3O4. The amount ofCo2+ ions increased as the Co3O4 increased. With a maximum of Co3+ ions, the highest transmittance wasobserved.

Trace analysis of Cd and Pb at surface modified thick film graphite electrode with Bi nanopowder has been carried out using square-wave anodic stripping voltammetry (SWASV) technique. Bi nanopowder synthesized by gas condensation (GC) method showed the size of nm with BET surface area, . For a strong adhesion of the Bi nanopowder onto the screen printed carbon paste electrode, nafion solution was added into Bi-containing suspension. From the SWASV, it was found that the Bi nanopowder electrode exhibited a well-defined responses relating to the oxidations of Cd and Pb. The current peak intensity increased with increasing concentration of Cd and Pb. From the linear relationship between Cd/Pb concentrations and peak current, the sensitivity of the Bi nanopowder electrode was quantitatively estimated. The detection limit of the electrode was estimated to be and for Cd and Pb, respectively, on the basis of the signal-to-noise characteristics (S/N=3) of the response for the solution under a 10 min accumulation.

In order to develop "textile electrode - sensing clothing" which is a sort of smart clothing to measure electric activities of heart, we propose possible ways to develop textile electrode and design of sensing clothing, ultimately aiming to develop "ECG sensing clothing for lifestyle monitoring". Conventional sensors for measuring typical electric activities of heart keep certain distance between measuring electrodes to measure signals for electric activities of heart, but these sensors often cause inappropriate factors (e.g. motional artifacts, inconvenience of use, etc) for monitoring natural cardiac activities in our daily life. In addition, most of textile electrodes have made it difficult to collect data due to high impedance and unstable contact between skin and electrodes. To overcome these questions, we minimized distance between electrodes and skin to maximize convenience of use. And in order to complement contact between skin electrodes, we modified textile electrode's form and developed ways to design clothing. As a result, we could find out clinical significance by investigating possible associations of clinical electrocardiogram (ECG) with variation of distance between electrodes, and could also demonstrate clinically significant associations between textile electrode developed herein and clothing.