본 연구에서는 Cellulose Nano-Crystals (CNCs) 수용액을 이용하여 시멘트 페이스트의 강도 향상에 대한 실험을 수행하고 이 연구결과를 토대로 하여 CNC 혼입에 따른 섬유보강 고인성 시멘트 복합체의 강도 특성에 관한 실험을 진행하였다. 먼저, CNC의 최적 배합비를 결정하기 위한 일환으로, 골재를 포함하지 않은 시멘트 페이스트의 강도 특성을 비교하기 위해 CNC 혼입율에 따라 수용액을 제조하였다. CNC 혼입율은 시멘트 대비 0.1, 0.2, 0.4 vol.%를 주요 변수로 하였고, 이에 따른 휨강도는 0.4 vol.%에서 플레인 시험체와 비교시 최대 8 배까지 강도가 증가하는 것을 확인할 수 있었다. 이 연구결과와 기존 연구결과를 토대로 하여, 본 연구에서는 0.4, 0.8 및 1.2 vol.%의 CNC 혼입율을 주요변수로 한 강섬유와 아마섬유를 활용한 섬유보강 고인성 시멘트 복합체 시험체를 제작한 후 역학적 강도 특성을 평가하여 섬유보강 고인성 시멘트 복합체의 구조적 성능을 규명하였다.

H13 tool steels are widely used as metallic mold materials due to their high hardness and thermal stability. Recently, many studies are undertaken to satisfy the demands for manufacturing the complex shape of the mold using a 3D printing technique. It is reported that the mechanical properties of 3D printed materials are lower than those of commercial forged alloys owing to micropores. In this study, we investigate the effect of microstructures and defects on mechanical properties in the 3D printed H13 tool steels. H13 tool steel is fabricated using a selective laser melting(SLM) process with a scan speed of 200 mm/ s and a layer thickness of 25 μm. Microstructures are observed and porosities are measured by optical and scanning electron microscopy in the X-, Y-, and Z-directions with various the build heights. Tiny keyhole type pores are observed with a porosity of 0.4%, which shows the lowest porosity in the center region. The measured Vickers hardness is around 550 HV and the yield and tensile strength are 1400 and 1700 MPa, respectively. The tensile properties are predicted using two empirical equations through the measured values of the Vickers hardness. The prediction of tensile strength has high accuracy with the experimental data of the 3D printed H13 tool steel. The effects of porosities and unmelted powders on mechanical properties are also elucidated by the metallic fractography analysis to understand tensile and fracture behavior.

This investigates the microstructure and mechanical properties of Al hybrid material prepared by electromagnetic duo-casting to determine the effect of heat treatment. The hybrid material is composed of an Al-Mg-Si alloy, pure Al and the interface between the Al-Mg-Si alloy and pure Al. It is heat-treated at 373, 573 and 773K for 1h and T6 treated (solution treatment at 773K for 1h and aging at 433K for 5h). As the temperature increases, the grain size of the Al-Mg-Si alloy in the hybrid material increases. The grain size of the T6 treated Al-Mg-Si alloy is similar to that of one heat-treated at 773K for 1h. The interface region where the micro-hardness becomes large from the pure Al to the Al-Mg-Si alloy widens with an increasing heat temperature. The hybrid material with a macro-interface parallel to the tensile direction experiences increased tensile strength, 0.2% proof stress and the decreased elongation after T6 heat treatment. On the other hand, in the vertical direction to the tensile direction, there is no great difference with heat treatment. The bending strength of the hybrid material with a long macro-interface to the bending direction is higher than that with a short macro-interface, which is improved by heat treatment. The hybrid material with a long macro-interface to the bending direction is fractured by cracking through the eutectic structure in the Al-Mg-Si alloy. However, in the hybrid material with a short macro-interface, the bending deformation is observed only in the limited pure Al.

Intermetallic compound matrix composites have been expected to be established as high temperature structural components. Ni3Al is a representative intermetallic alloy, which has excellent ductility even at room temperature by adding certain alloying elements. Ni3Al matrix composites with aluminum oxide particles, which are formed by the in-situ reaction between the alloy and aluminum borate whiskers, are fabricated by a powder metallurgical method. The addition of aluminum borate whiskers disperses the synthetic aluminum oxide particles during sintering and dramatically increases the strength of the composite. The uniform dispersion of reaction synthesized aluminum oxide particles and the uniform solution of boron in the matrix seem to play an important role in the improvement in strength. There is a dramatic increase in strength with the addition of the whisker, and the maximum value is obtained at a 10 vol% addition of whisker. The Ni3Al composite with 10 vol% aluminum oxide particles 0.3 μm in size and with 0.1 wt% boron powder fabricated by the conventional powder metallurgical process does not have such high strength because of inhomogeneous distribution of aluminum oxide particles and of boron. The tensile strength of the Ni3Al with a 10 vol% aluminum borate whisker reaches more than twice the value, 930 MPa, of the parent alloy. No third phase is observed between the aluminum oxide and the matrix.

This study investigates the effects of isothermal holding temperature and time on the microstructure, hardness and Charpy impact properties of medium-carbon bainitic steel specimens. Medium-carbon steel specimens with different bainitic microstructures are fabricated by varying the isothermal conditions and their microstructures are characterized using OM, SEM and EBSD analysis. Hardness and Charpy impact tests are also performed to examine the correlation of microstructure and mechanical properties. The microstructural analysis results reveal that granular bainite, bainitic ferrite, lath martensite and retained austenite form differently in the specimens. The volume fraction of granular bainite and bainitic ferrite increases as the isothermal holding temperature increases, which decreases the hardness of specimens isothermally heat-treated at 300 ℃ or higher. The specimens isothermally heat-treated at 250 ℃ exhibit the highest hardness due to the formation of lath martensite, irrespective of isothermal holding time. The Charpy impact test results indicate that increasing isothermal holding time improves the impact toughness because of the increase in volume fraction of granular bainite and bainitic ferrite, which have a relatively soft microstructure compared to lath martensite for specimens isothermally heat-treated at 250 ℃ and 300 ℃.

In this study, three kinds of steels are manufactured by varying the rolling conditions, and their microstructures are analyzed. Tensile and Charpy impact tests are performed at room temperature to investigate the correlation between microstructure and mechanical properties. In addition, heat affected zone(HAZ) specimens are fabricated through the simulation of the welding process, and the HAZ microstructure is analyzed. The Charpy impact test of the HAZ specimens is performed at -40 oC to investigate the low temperature HAZ toughness. The main microstructures of steels are quasi-polygonal ferrite and pearlite with fine grains. Because coarse granular bainite forms with an increasing finish rolling temperature, the strength decreases and elongation increases. In the steel with the lowest reduction ratio, coarse granular bainite forms. In the HAZ specimens, fine acicular ferrites are the main features of the microstructure. The volume fraction of coarse bainitic ferrite and granular bainite increases with an increasing finish rolling temperature. The Charpy impact energy at -40 oC decreases with an increasing volume fraction of bainitic ferrite and granular bainite. In the HAZ specimen with the lowest reduction ratio, coarse bainitic ferrite and granular bainite forms and the Charpy impact energy at -40 oC is the lowest.

This paper presents a study of the microstructure and mechanical properties of commercial high-hardness armor (HHA) steels tempered at different temperatures. Although the as-received specimens of all the steels exhibit a tempered martensite structure with lath type morphology, the A steel, which has the smallest carbon content, had the lowest hardness due to reduced solid solution hardening and larger lath thickness, irrespective of tempering conditions. As the tempering temperature increases, the hardness of the steels steadily decreases because dislocation density decreases and the lath thickness of martensite increases due to recovery and over-aging effects. When the variations in hardness plotted as a function of tempering temperature are compared with the hardness of the as-received specimens, it seems that the B steel, which has the highest yield and tensile strengths, is fabricated by quenching, while the other steels are fabricated by quenching and tempering. On the other hand, the impact properties of the steels are affected by specimen orientation and test temperature as well as microstructure. Based on these results, the effect of tempering on the microstructure and mechanical properties of commercial high-hardness armor steels is discussed.

This study is conducted as a preliminary research to verify the feasibility of Ti-based Oxide dispersion strengthened (ODS) alloy. Pure-Ti powder is mixed with Y2O3 powder and subsequently, mechanically alloyed at -150oC. The Ti-based ODS powder is hot-isostatically pressed and subsequently hot-rolled for recrystallization. The microstructure consists of elongated grains and Y excess fine particles. The oxide particle size is larger than that of the typical Febased ODS steel. Tensile test shows that the tensile ductility is approximately 25%, while the strength is significantly higher than that of pure Ti. The high-temperature hardness of the Ti-ODS alloy is also significantly higher than that of pure Ti at all temperatures, while being lower than that of Ti-6Al-4V. The dimple structure is well developed, and no evidence of cleavage fracture surface is observed in the fracture surface of the tensile specimen.

Particle size reduction is an important step in many technological operations. The process itself is defined as the mechanical breakdown of solids into smaller particles to increase the surface area and induce defects in solids, which are needed for subsequent operations such as chemical reactions. To fabricate nano-sized particles, several tens to hundreds of micron size ceramic beads, formed through high energy milling process, are required. To minimize the contamination effects during highenergy milling, the mechanical properties of zirconia beads are very important. Generally, the mechanical properties of Y2O3 stabilized tetragonal zirconia beads are closely related to the mechanism of phase change from tetragonal to monoclinic phase via external mechanical forces. Therefore, Y2O3 distribution in the sintered zirconia beads must also be closely related with the mechanical properties of the beads. In this work, commercially available 100μm-size beads are analyzed from the point of view of microstructure, composition homogeneity (especially for Y2O3), mechanical properties, and attrition rate.

Effects of annealing temperature on the microstructure and mechanical properties through thickness of a Cu-3.0Ni- 0.7Si alloy processed by differential speed rolling are investigated in detail. The copper alloy with a thickness of 3 mm is rolled to a 50 % reduction at ambient temperature without lubricant and subsequently annealed for 0.5 h at 200-900 oC. The microstructure of the copper alloy after annealing is different in the thickness direction depending on the amount of the shear and compressive strain introduced by the rolling; the recrystallization occurs first in the upper roll side and center regions which are largely shear-deformed. The complete recrystallization occurs at an annealing temperature of 800 oC. The grain size after the complete recrystallization is finer than that of the conventional rolling. The hardness distribution of the specimens annealed at 500-700 oC is not uniform in the thickness direction due to partial recrystallization. This ununiformity of hardness corresponds well to the amount of shear strain in the thickness direction. The average hardness and ultimate tensile strength has the maximum values of 250 Hv and 450 Mpa, respectively, in the specimen annealed at 400 oC. It is considered that the complex mode of strain introduced by rolling directly affects the microstructure and the mechanical properties of the annealed specimens.

Recently, redevelopment and reconstruction projects have caused problems such as depletion of natural aggregates, and the use of recycled aggregate is being reevaluated as an optimal alternative. Therefore, in this study, the mechanical and deformation characteristics of Environment-Friendly Recycled Coarse Aggregate (here after, EFRCA) concrete reinforced with para-aramid fiber with high strength and high elasticity are examined. The experimental main parameters were EFRCA replacement ratio (0, 30 and 50%) and para-aramid fiber volume fraction (0, 0.75 and 1.0%). Experimental results show that the EFRCA concrete has lower compressive strength than plain concrete. However, compared with the natural aggregate, the EFRCA concrete, which exhibited low material properties, showed almost the same performance as plain concrete, such as increased flexural strength and improved ductility by incorporating para-aramid fibers. Through the experiment, it is considered that the most suitable para-aramid volume fraction is 0.75%. Based on these results, the experimental results related to the performance degradation of EFRCA concrete containing para-aramid fibers are secured and basic data for determining the reuse possibility and reinforcement method of structures are presented.

Effects of annealing temperature on the microstructure and mechanical properties through thickness of a cold-rolled Cu-3.0Ni-0.7Si alloy were investigated in detail. The copper alloy with thickness of 3 mm was rolled to 50 % reduction at ambient temperature without lubricant and subsequently annealed for 0.5h at 200~900 oC. The microstructure of the copper alloy after annealing was different in thickness direction depending on an amount of the shear and compressive strain introduced by rolling; the recrystallization occurred first in surface regions shear-deformed largely. The hardness distribution of the specimens annealed at 500~700 oC was not uniform in thickness direction due to partial recrystallization. This ununiformity of hardness corresponded well with an amount of shear strain in thickness direction. The average hardness and ultimate tensile strength showed the maximum values of 250Hv and 450MPa in specimen annealed at 400 oC, respectively. It is considered that the complex mode of strain introduced by rolling effected directly on the microstructure and the mechanical properties of the annealed specimens.

스테인레스 스틸에 대한 도료수지의 기계적 특성은 SEM, FT-IR, 인장특성, 그리고 [NCO]/ [OH]의 mole %, 입도분석에 의해 측정하였다. 친환경적인 도료에 관한 관심이 고조됨에 따라 스테인레스 스틸 등의 금속에 코팅하는 무용제 도료를 합성하였다. 폴리올, MDI, 충진제, 실리콘 계면활성제, 촉매 등이 함유된 기존 도료수지보다 식물성 오일이 함유된 폴리올, MDI, 충진제, 실리콘 계면활성제, 촉매로 이루어진 합성 도료 수지의 코팅이 내구력과 강도가 양호하였다. 견고한 도료 수지의 기계적 특성은 식물성 오일이 함유된 폴리올로 합성된 폴리우레탄 코팅의 접촉각이 더 컸으며, [NCO]/[OH]의 mole%가 증가함에 따라 강도가 증가하였다. 결론적으로 식물성 오일이 함유된 친환경 도료가 스테인레스 스틸 같은 금속물질의 부식방지용 코팅에 좋은 물질이다.

난대림에서 생육하고 있는 상록활엽수를 자원화하기 위해서 참식나무의 조직적, 물리적, 역학적 특성 을 분석하였다. 조직적 특성은 방사조직의 크기, 너비, 수와 도관의 크기를 관찰하였다. 참식나무의 전 수축률은 접선방향 11.00%, 방사방향 4.64%를 나타내었고 기건수축률은 접선방향 8.00%, 방사방향 2.88%를 나타내었다. 평균연륜폭은 2.93mm, 기건밀도는 0.52g/cm3, 기본밀도는 0.39g/cm3이었다. 휨 강도는 76.97Mpa, 압축강도는 10.97Mpa, 전단강도는 10.13Mpa이었다. 참식나무의 평균연륜폭과 강도 와의 관계는 1% 수준에서 유의성이 인정되는 부의 상관관계가 나타났다. 참식나무는 평균연륜폭의 높은 증가에 반해 강도 감소율은 비교적 낮은 감소를 나타내어 생장률 증가에 따른 강도 감소가 낮아 대경재 의 이용이 경제적이라고 판단된다. 남부지역의 참식나무는 온대에서 난대로 기후가 변화하는 난대 지역 의 산림자원으로 본 목재재질특성 분석결과 유용한 산림자원으로 활용할 수 있을 것으로 생각된다.

The use of continuous welded rail is increasing because of its many advantages, including vibration reduction, enhanced driving stability, and maintenance cost savings. In this work, two different types of continuous welded rails were examined to determine the influence of repeated wheel-rail contact on the crystal structure, microstructure and mechanical properties of the rails. The crystal structure was determined by x-ray diffraction, and the microstructure was examined using optical microscopy and scanning electron microscopy. Tensile and microhardness tests were conducted to examine the mechanical behaviors of prepared specimens taken from different positions in the cross section of both newly manufactured rail and worn rail. Analysis revealed that both the new and worn rail had a mixed microstructure consisting of ferrite and pearlite. The specimens from the top position of each rail exhibited decreased lamella spacing of the pearlite and increased yield strength, ultimate tensile strength and hardness, as compared with those from other positions of the rail. It is thought that the enhanced mechanical property on the top position of the worn rail might be explained by a mixed effect resulting from a directional microstructure, the decreased lamella spacing of pearlite, and work hardening by the repeated wheel-rail contact stress.