In this paper, we investigate the relationship between control system of Bosch system and that of Delphi system by measuring the high and low voltage waveform, current waveform and fuel injection quantity of D-2 and R- engines. Waveform measurements are used the PICO scope and the CDS tester. The injectors of D-2 and R-engines were tested under no load condition using injector with normal fuel injection quantity, injector with small fuel injection quantity and injector with many fuel injection quantity. The relation between current energy and fuel injection quantity shows that the injector variation rate of D2-engine is much larger than that of R-engine. The injector current energy of the D2-engine was more linear than that of the R-engine, therefore making the system more stable. Although the control system of the D2-engine is a more stable system only in terms of the durability of the internal parts of the injector, the injector of the R-engine has a good response because the current value is large.

In this paper, 'Pico scope' was used to measure and analyze high voltage waveforms of 'Grade injector' and 'IQA injector' due to defective solenoid injector of CRDI diesel engine, and the following conclusions were obtained. In the case of the injector of 'Grade Injector' and 'IQA Injector', there was no change in the injection timing of the injector while the injector was installed. However, by controlling the operation time, It is judged that the injector control is insufficiently controlled when the number of revolutions of the engine is increased to 2000 rpm and 3000 rpm in the idling state in the idling state because the injector failure is precisely controlled in the idling state, When determining the fault injector, the waveform of the 'Grade injector' and 'IQA injector' can be detected by waveform analysis by comparing the injection control time by measuring the high voltage waveform of the injector control in idle idling state. Can be easily diagnosed and maintained. I hope this study will be handed to the mechanics to make diagnosis of CRDI injector convenient.

This paper investigates the relationship between the waveform area and fuel injection quantity. It is on developing on analysis method of waveform the effect of waveform area on fuel injection quantity of CRDI Diesel engine. The experimental methods using Pico oscilloscope and fuel injection tester are employed to measure current and voltage waveform and fuel injection quantity of solenoid injector. The one normal and two abnormal solenoid injectors are used. The experiment is carried out during no-load condition. A summary of the important results are as follows. 1) The area of the voltage and current waveform of the abnormal injector becomes larger than the that of normal injector, and the area of the current and voltage waveform is inversely proportional to the fuel injection quantity. 2) The area of the current waveform can be obtained more accurate results than that of voltage waveform. 3) It is possible to infer the fuel injection quantity by measuring the current waveform and calculating the area.

This paper is on developing the waveform analysis method in driving control of solenoid injector of CRDI diesel engine. The experimental methods using Pico oscilloscope and scan tool is employed to measure current and voltage waveform of solenoid injector. The solenoid injector are used 1 normal and 2 abnormal injectors. The experiment is carried out during no-load condition. The magnitude of pressure drop is largest main duration, pre and pilot duration in the order named in case of normal injector, whereas was largest pilot duration, pre and main duration in the order named in case of abnormal injectors.

This paper investigates the waveform analysis of voltage and current waveform from CRDI engine. It is on developing on analysis method of waveform CRDI Diesel engine. The experimental methods using Pico oscilloscope are employed to measure current and voltage waveform of solenoid injector from CRDI engine. The one normal and two abnormal solenoid injectors are used. The experiment is carried out during no-load condition. A summary of the important results are as follows. 1) The area of the voltage and current waveform of the abnormal injector becomes larger than the that of normal injector. 2) The area of the current waveform can be obtained more accurate results than that of voltage waveform.