PURPOSES : Concrete, which is a construction material, is the most widely used compression material; however, unlike steel, it exhibits nonlinear material characteristics. Therefore, to examine the behavior of structures under the nonlinear conditions of concrete materials, one must select an appropriate numerical-analysis technique and a reasonable material model. When performing the nonlinear numerical analysis of a structure using general-purpose structural analysis software, the stress–strain curve or the Mohr–Coulomb failure criterion is typically employed to consider the nonlinear material characteristics. In this study, an efficient nonlinear numerical analysis is conducted by defining the stress–strain curves and Mohr–Coulomb parameters applicable to Strand7 to examine and design the stability of reinforced concrete structures. METHODS : This study was conducted by improving existing data. Based on the tensile region of the concrete stress–strain curve presented in a simple shape and the results of the splitting test, the proposed Mohr–Coulomb parameter was improved based on regulations stipulated in the design standards of concrete structures. The characteristics and usability of the improved material models were examined using concrete splitting tensile and bending models. RESULTS : A yield area distribution similar to that of the reference data is obtained when the Mohr–Coulomb material model is used in the numerical analysis of the concrete splitting tension, thus confirming the validity of the model. In the Mohr–Coulomb material model, nonlinear resistance continues even after the maximum reaction force occurs. However, when the stress–strain curve material model is applied, at the moment the maximum reaction force occurs, the material yields and begins to be damaged. In addition, by applying the Mohr–Coulomb material model to the bending numerical-analysis model, the magnitude of stress in the tensile region from the initial stage exceeds the yield stress defined in the stress–strain curve. CONCLUSIONS : Based on a series of examples, the usability of the proposed concrete stress–strain curve and Mohr–Coulomb parameters is confirmed. However, to obtain numerical-analysis results that are consistent with the nonlinear behavior of actual structures, nonlinear testing of reinforced concrete structures shall be conducted and material models shall be improved.
The most comprehensive and particularly reliable method for non-destructively measuring the residual stress of the surface layer of metals is the sin method. When X-rays were used the relationship of sin measured on the surface layer of the processing metal did not show linearity when the sin method was used. In this case, since the effective penetration depth changes according to the changing direction of the incident X-ray, becomes a sin function. Since cannot be used as a constant, the relationship in sin cannot be linear. Therefore, in this paper, the orthogonal function method according to Warren’s diffraction theory and the basic profile of normal distribution were synthesized, and the X-ray diffraction profile was calculated and reviewed when there was a linear strain (stress) gradient on the surface. When there is a strain gradient, the X-ray diffraction profile becomes asymmetric, and as a result, the peak position, the position of half-maximum, and the centroid position show different values. The difference between the peak position and the centroid position appeared more clearly as the strain (stress) gradient became larger, and the basic profile width was smaller. The weighted average strain enables stress analysis when there is a strain (stress) gradient, based on the strain value corresponding to the centroid position of the diffracted X-rays. At the 1/5 max height of X-ray diffraction, the position where the diffracted X-ray is divided into two by drawing a straight line parallel to the background, corresponds approximately to the centroid position.
PURPOSES: This study is primarily focused on evaluating the effects of the non-linear stress-strain behavior of RAP concrete on structural response characteristics as is applicable to concrete pavement. METHODS : A 3D FE model was developed by incorporating the actual stress-strain behavior of RAP concrete obtained via flexural strength testing as a material property model to evaluate the effects of the non-linear stress-strain behavior to failure on the maximum stresses in the concrete slab and potential performance prediction results. In addition, a typical linear elastic model was employed to analyze the structural responses for comparison purposes. The analytical results from the FE model incorporating the actual stress-strain behavior of RAP concrete were compared to the corresponding results from the linear elastic FE model. RESULTS : The results indicate that the linear elastic model tends to yield higher predicted maximum stresses in the concrete as compared to those obtained via the actual stress-strain model. Consequently, these higher predicted stresses lead to a difference in potential performance of the concrete pavement containing RAP. CONCLUSIONS : Analysis of the concrete pavement containing RAP demonstrated that an appropriate analytical model using the actual stress-strain characteristics should be employed to calculate the structural responses of RAP concrete pavement instead of simply assuming the concrete to be a linear elastic material.
In this study, analysis on the stiffness of the headrest, the stiffness of front-rear load and the torsion of cushion frame was performed using finite element method in order to investigate the properties of the stress-deformation by material characteristics according to the test requirements of FMVSS (Federal Motor Vehicle Safety Standard). The results are shown that AZ31 (Mg alloy) and A365 (Al alloy) with low modulus of elasticity and density have higher strain rate than steel in terms of stress-deformation and meet the standards for safety within 108 mm of the maximum amount of deformation. Considering it’s safety and durability, however, the selection of AZ31 for light weight seems difficult to gain the reliability because it causes an excessive deformation, and therefore it is not expected to be used for recliner where stress is concentrated and also the bracket linking rail and cushion frame.
In this paper, an efficient yet accurate method for the thermal stress analysis using a first order shear deformation theory(FSDT) is presented. The main objective herein is to systematically modify transverse shear strain energy through the mixed variational theorem(MVT). In the mixed formulation, independent transverse shear stresses are taken from the efficient higher-order zigzag plate theory, and the in-plane displacements are assumed to be those of the FSDT. Moreover, a smooth parabolic distribution through the thickness is assumed in the transverse normal displacement field in order to consider a transverse normal deformation. The resulting strain energy expression is referred to as an enhanced first order shear deformation theory, which is obtained via the mixed variational theorem with transverse normal deformation effect(EFSDTM_TN). The EFSDTM_TN has the same computational advantage as the FSDT_TN(FSDT with transverse normal deformation effect) does, which allows us to improve the through-the-thickness distributions of displacements and stresses via the recovery procedure. The thermal stresses obtained by the present theory are compared with those of the FSDT_TN and three-dimensional elasticity.
공기막구조물의 공간형성방법은 크게 단일공기막과 이중공기막 방식으로 나뉜다. 내압으로 인해 평형곡면이 형성되는 공기막구조물의 형상은 형태의 변화가 외력에 의해 크게 변형되거나 응력이 집중되지 않는 등장력 곡면으로 많이 이용된다. 따라서 본 연구에서는 공기막 구조물의 초기 형성된 형상에 대해서 설계하중조합에 대한 구조해석을 비선형 전용해석프로그램인 NASS를 이용하여 수행한 후 변형형상을 살펴보고, 최대응력을 이용하여 안전성을 검토한다. 해석 모델은 사면에서 지지되는 장방형 단일공기막 구조물을 대상으로 하며, 직교이방성을 고려하여 비선형 증분해석을 수행한다.
강구조물에 있어서 여러 가지 환경요인에 의해 균열 및 부식 등의 문제가 발생되고 있다. 이는 구조물의 내구성을 저하시키는 요인이 된다. 이와 같은 문제를 해결하기 위해 용접 보수보강방법을 사용할 수 있다. 이러한 보수용접은 전단 및 용접과 같은 입열 과정을 필연적으로 수반하고 있다. 따라서 이러한 입열과정에 있어서 발생되는 잔류응력 및 변형의 예측제어방지는 구조물의 안전이라는 측면에서 볼 때 중요하다고 할 수 있다. 본 연구에서는 2차원 및 3차원 유한요소 해석을 수행하여 가스전단 및 아크용접에 의해 얻어진 절단 및 용접 잔류응력과 변형을 구하였으며, 2차원 및 3차원 해석기법에 따른 그 값의 정도를 명확히 하였다. 해석기법에 따라 2차원 및 3차원 해석을 수행하여 얻은 절단 및 용접 잔류응련의 분포 및 그 절대치는 유사한 값을 나타내었다.
본 연구에서는 제방 축조재료로 사용되는 낙동강 모래의 응력-변형 거동특성 파악을 위하여, 삼축압축시험 등을 포함한 실내시험을 실시하였고, 조립재료의 거동 표현에 적합한 개별요소방법을 적용한 수치 모델링을 실시하였다. 개별요소해석은 삼축압축시험 과정을 모델링하였으며, 이때 이용된 미시물성치는 물성치 보정과정을 통해 산정되었다. 특정 구속압조건을 만족시키는 미시 물성치의 산정이 가능하다면, 이 미시물성치의 이용을 통해 다른 구속압조건 및 응력재하 조건에서의 거동예측에 있어, 개별요소방법이 매우 효과적으로 이용될 수 있음을 알 수 있었다.
평형트러스모델, Mohr적합트러스모델, 그리고 연성트러스모델은 회전각에 기초하기 때문에 회전각모델이라 불리 운다. 이러한 회전각모델들은 콘크리트기여도를 예측할 수 없는 단점이 있다. 콘크리트 기여 성분을 계산할 수 있는 MCFT(Modified Compression Field Theory)나 RA-STM(Rotating Angle-Softening Truss Model) 같은 최근 트러스모델(Modern Truss Model, MTM)은 균열이 발생한 철근콘크리트요소를 연속체 재료로 취급한다. 또한 MTM은 평형조건과 적합조건 그리고 2축 상태에서 콘크리트의 연성 응력-변형률 관계를 이용하여 비선형해석을 수행하고 있다. 본 연구는 전단응력-변형률의 전체 이력 상태를 모두 계산하지 않고, 철근항복과 스트럿 압괴(crushing failure) 파괴기준을 이용하여 해를 찾는 방법으로 수렴속도를 개선한 것이다. 이 알고리즘을 이용하여 Hsu가 실험한 9개의 전단응력-변형률 자료를 분석하였다.
For the rational and economic design of the structural elements of ships which is built using welding, the ultimate strength analyses of the plates having initial imperfections, such as welding residual stresses and strains, are needful. The welding deformation usually relied on approximative equations or based on expert's experience. But in this paper, for the thermal elasto-plastic analysis of plates, the finite element analysis was performed, based on initial strain method. In formulating the incremental analysis, unbalanced force terns were included. In the plastic domain during the incremental process, the 2nd order terns stress increment and yield stress increment were considered, so that time increment could be controlled for a more stable solution. The ultimate strength analysis program of the plates having initial imperfections was made. The ultimate strength analysis was carried out based on the results of the welding deformations of this paper. In the ultimate strength analysis the Rayleigh-Ritz method based on the minimum potential theory was used.