본 논문에서는 상용프로그램을 이용한 유한요소해석을 통하여 포스트텐션 정착구역에서 보다 효율적인 응력분산이 가능 한 비부착식 단일 강연선용 포스트텐션 정착구 형상을 개발하는 것을 목표로 하였다. 이를 위하여 정착구 형상을 구성하는 각 부분의 변수해석을 수행하였다. 본 연구에서 제안한 정착구 형상을 사용하였을 때 발생하는 최대파열응력이 기존의 정착 구를 사용한 경우와 비교하여 정착구역내의 최대파열응력이 감소함을 확인하였다. 또한 본 연구의 정착구 형상을 사용하는 경우 최대파열응력 산정을 위해 AASHTO 및 기존 연구자들의 파열력 산정식을 통해 산출된 파열력을 비교 및 분석하였다. 그 결과 정착구 형상에 따른 위치계수를 수정한 파열력 산정식을 적용할 경우 정착구역이 효율적인 보강설계가 가능할 것으 로 판단되었다.

프리스트레스 콘크리트 정착부의 설계를 위해 AASHTO 및 PTI에서 관련 설계식을 제안하고 있다. 그러나 이러한 설계식은 구조물의 긴장력이 단순 지압판을 통해 구조 전반으로 전달된다는 가정으로 유도된 것으로 실제 구조물에 적용되는 상용 정착구의 형태와는 차이가 있다. 이 논문에서는 하중전달 시험에 의한 실험적 방법과 3차원 고체요소를 사용한 비선형 유한요소해석 프로그램을 이용한 해석적 방법을 통해 정착구의 형상 변수에 따른 정착부의 거동특성 변화에 대한 연구를 수행하였다. 하중전달시험 결과에서 얻어진 하중변위 곡선 및 극한하중 값을 해석을 통해 얻은 결과와 비교하여 유한요소모델의 적합성을 확인하였다. 또한 정착구의 리브의 설치위치, 리브의 개수, 리브의 설치길이를 주요 변수로 설정하여 형상변수에 따른 매개변수 연구를 수행하였다.

For the last decade many bridges and buildings have experienced flexural strengthening with the fiber reinforced polymer(FRP) bonding system, demands for increasing heavy traffic loads and the changing of the code application. Of the many strengthening systems, NSM(near surface mounted) system with FRP has become attractive and popular way of strengthening for the existed RC structures and many studies and applications of this technique have significantly increased all over the world. Meanwhile, polymer mortar that contains much of the same ingredients as cement but includes the addition of certain polymer resins for enhancing desired physical properties, has been used as an alternative adhesive. This paper focuses on flexural behaviour of CFRP-bar NSM system with variables such as kinds of adhesive, anchorage, sectional aspect ratio. Based on the test results and test-to -predicted ratio, this paper provides researchers and practical engineers a fundamental knowledge and intuition.

A damage case of parallel strand cable anchorage was introduced, in which 7 strands were slipped from each wedge at the anchorage of the cable stayed bridge in service. Also, a cable damage detection scheme was proposed on the basis of tension force measurement and model updating method by least square estimation to minimize tension variation. The proposed scheme has been verified from analytical simulations and the actual damage case. The damaged cable leading to tension variation more than noise level of cable force measurement was successfully detected with 7~8 strands damage indication of 2% error in the actual strand slippage case.

Based on the experiment, characteristic of local stresses and deformation in the anchorhead and wedges with prestressing of PSC slab was investigated in this study. As a result, local stresses exceeded yeild stress in the contacts of anchorhead and wedges and in the lower sides of anchorhead

Simulation studies were performed to study the possibility of tensile force monitoring with piezoelectric sensors attached on anchorage devices of bonded tendon systems. The results showed that the impedance signals from piezoelectric sensors has sensitivity enough to evaluate the effective tensile force.

In this paper, the load transfer test of circular shaped anchorage block to reduce the spacing. The test is in compliance with ETAG013 and KCI-PS101. Test results showed that the strain in compliance with ETAG013 and KCI-PS101 stabilization that satisfy all the criteria.

The specimen shall contain tohose anchorage components and bursting reinforcement which will be embedded in the structural concrete, and their arrangement has comply with the intended application and with the specification as per the ETAG013. Components shall randomly selected.

In this study, the strut-tie model used for the analysis and design of the anchorage zone of the PSC modular bridge by comparing with the result of the approximate analytical method. The result shows that the bursting force obtained by approximate analytical method were increased about 2 times in comparison with the result of strut-tie model.