Many piping systems installed in the power plant are directly related to the safety and operation of the plant. Various dampers have been applied to the piping system to reduce the damage caused by earthquakes. In order to reduce the vibration of the piping system, this study developed a steel coil damper (SCD) with a straightforward structure but excellent damping performance. SCD reduces the vibration of the objective structure by hysteretic damping. The new SCD damper can be applied to high-temperature environments since it consists of steel members. The paper introduces a design method for the elastoplastic coil spring, which is the critical element of SCD. The practical applicability of the design procedure was validated by comparing the nonlinear force-displacement curves calculated by design equations with the results obtained from nonlinear finite element analysis and repeated loading test. It was found that the designed SCD’s have a damping ratio higher than 25%. In addition, this study performed a set of seismic tests using a shaking table with an existing piping system to verify the vibration control capacity on the piping system by SCD. Test results prove that the SCD can effectively control the displacement vibration of the piping system up to 80%.
In this paper, an experimental study was carried out for vibration control of cable bridges with structurally flexible characteristics. For the experiment on vibration control, a model bridge was constructed by reducing the Seohae Grand Bridge and the shear type MR damper was designed using the wind load response measured at Seohae Grand Bridge. The shear type MR damper was installed in the vertical direction at the middle span of the model bridge, and dynamic modeling was performed using the power model. The tests of the vibration control were carried out by non-control, passive on/off control and Lyapunov control method on model bridge with scaled wind load response. The performance of the vibration control was evaluated by calculating absolute maximum displacement, RMS displacement, absolute maximum acceleration, RMS acceleration, and size of applied power using the response (displacement, acceleration, etc.) from the model bridge. As a result, the power model was effective in simulating the nonlinear behavior of the MR damper, and the Lyapunov control method using the MR damper was able to control the vibration of the structure and reduce the size of the power supply.
This paper is concerned with an experimental research to control of random vibration caused by external loads specially in cable-stayed bridges which tend to be structurally flexible. For the vibration control, we produced a model structure modelled on Seohae Grand Bridge, and we designed a shear type MR damper. On the center of its middle span, we placed a shear type MR damper which was to control its vibration and also acquire its structural responses such as displacement and acceleration at the same site. The experiments concerning controlling vibration were performed according to a variety of theories including un-control, passive on/off control, and clipped-optimal control. Its control performance was evaluated in terms of the absolute maximum displacements, RMS displacements, the absolute maximum accelerations, RMS accelerations, and the total power required to control the bridge which differ from each different experiment method. Among all the methods applied in this paper, clipped-optimal control method turned out to be the most effective to reduces of displacements, accelerations, and external power. Finally, It is proven that the clipped-optimal control method was effective and useful in the vibration control employing a semi-active devices such MR damper.
Damped outrigger systems have been proposed as a novel energy dissipation system to protect tall buildings from severe earthquakes and strong wind loads. In this study, semi-active damping devices such as magnetorheological (MR) dampers instead of passive dampers are installed vertically between the outrigger and perimeter columns to achieve large and adaptable energy dissipation. Control performance of semi-active outrigger damper system mainly depends on the control algorithm. Fuzzy logic control algorithm was used to generate command voltage sent to MR damper. Genetic algorithm was used to optimize the fuzzy logic controller. An artificial earthquake load was generated for numerical simulation. A simplified numerical model of damped outrigger system was developed. Based on numerical analyses, it has been shown that the semi-active damped outrigger system can effectively reduce both displacement and acceleration responses of the tall building in comparison with a passive outrigger damper system.
Recently, the concept of damped outrigger system has been proposed for tall buildings. But, structural characteristics and design method of this system were not sufficiently investigated to date. In this study, the dynamic response control performance of outrigger damper has been analyzed. To this end, a simplified analysis model with outrigger damper system has been developed. An artificial wind of 1000 seconds with 0.1 second time steps was generated by using a Kaimal spectrum. Analysis results show that outrigger damper system is more effective up to 20-23% in the control of dynamic response compared to conventional outrigger system. The increase of outrigger damper capacity usually results in the improved control performance. However, it is necessary to select that proper stiffness and damping values of the outrigger damper system because, the outrigger damper having large capacity is result in heavy financial burden.
장경간 교량의 낮은 감쇠비로 인하여 발생하는 구조물의 진동은 구조물의 안전성 및 사용성에 부정적인 영향을 미친다. 본 연구에서는 시공 중인 교량에 지배적으로 발생하는 연직 방향 진동을 제어하기 위하여 능동형 질량댐퍼(AMD)를 연구하였다. 대상 사장교의 동특성을 조사하기 위하여 모드 해석이 수행되었으며 이를 바탕으로 제어 성능과 설치 공간에 적합한 AMD를 설계하기 위하서 LQR(Linear Quadratic Regulator) 제어 알고리즘을 사용하였다. 성능 검증을 위하여 건설 단계의 대상 구조물과 AMD를 1/10.5의 상사비로 축소시킨 시작품을 설계, 제작하였으며, 시스템 식별을 수행하여 Linear Quadratic Gaussian (LQG) 제어 알고리즘을 적용하였다. 성능 실험 결과 AMD 제어 시에 높은 제어 효과를 구현하였으며, 실험 결과를 수치해석과 비교를 통하여 제어기 설계의 타당성을 확인하였다.
본 연구진은 최근 U자 형태인 액체댐퍼의 수직관을 다수의 셀(사각 기둥)로 나누어 셀 상부를 개폐함에 따라 다양한 고 유진동수를 쉽게 재현하는 새로운 멀티셀 액체댐퍼를 제시하였다. 이러한 댐퍼를 1층 건물 모형에 설치하여 진동대 실험을 수행하여 건물응답이 감소되는 것을 검증하였다. 64층의 풍응답인 가속도를 제어할 수 있도록 댐퍼를 설계하기 위하여 건 물을 1자유도계로 축소하였다. 가속도 기반 상사비인 1/20를 적용하여 1층 건물 모형과 새로운 댐퍼를 제작하였다. 설계 진 동수인 0.65Hz가 구현되도록 모형건물의 질량과 강성을 쉽게 조절할 수 있도록 탈부착식으로 제작하였다. 모형건물은 중량 을 부담하는 질량부와 하부에 스프링과 LM guide가 설치된 구동부로 나누어서 제작되었다. 18개의 셀을 가지는 액체댐퍼 를 제작하여 고유진동수 조절 범위가 0.65Hz~0.81Hz인 것을 파악하였다. 대형 진동대에 설치한 모형건물의 일방향 가진을 통하여 모형의 응답을 측정하고 모형상부에 멀티셀 액체댐퍼가 설치되었을 경우 모형의 응답을 측정하여 비교하였다. 진동 대 가속도를 입력과 모형건물의 가속도를 출력으로 하는 전달함수를 통해 결과를 나타내었다. 예상한 바와 같이 멀티셀 액 체댐퍼의 고유진동수를 건물의 진동수에 동조시켰을 경우 건물의 가속도 응답이 감소함을 알 수 있었다.
The vibration control of a flexible rotor supported on cavitated short squeeze film dampers is investigated. According to Pan's theory, the shape of cavitation in fluid film bearings depends on the level of oil supply pressure, as a result, both the direct and the cross coupled damping coefficients of a cavitated short squeeze film damper are varied widely. In this paper, controling the level of oil supply pressure by fuzzy theory, a significant reduction in journal eccentricity ratio, rotor amplitude and force transmissiblilty of a flexible rotor system is achieved.
In this study, a shear wall-slab damper system for seismic retrofitting of existing low-rise school buildings was proposed. The proposed system is to control the earthquake-induced vibration of the existing building structures using the energy dissipation effect of hysteretic damper inserted between the extended shear wall and existing moment frame. The numerical analyses were performed to investigate the vibration control efficiency of the shear wall-slab damper system and to identify the range of optimal yielding strength of the slab damper. In addition, variation of shear force of the extended shear wall with regard to the yield strength of the dampers in a range from 10 to 100 percent of the maximum base shear force of the retrofitted structure was investigated. The numerical analyses results showed that the maximum displacement of the structures with the slab damper whose yield strength is equal to 20 percent of the maximum base shear. On top of that, the slab damper system reduced the shear force of the shear wall by about 50 percent in comparison with the existing frame-shear wall system with rigid diaphragm slabs.
최근 바람 및 지진에 대한 진동제어를 목적으로 한 저항복점강재를 이용한 댐퍼가 많이 사용되고 있다. 그러나 전체 구조물의 진동에 영향을 미치는 저항복점강재의 동적특성 및 지진에너지 소산효과는 명확히 밝혀지지 않고 있다. 본 연구에서는 저항복점감재에 대한 반복재하실험 결과 및 저항복점감재를 정착한 3층 규모의 구조물에 대하여 실시한 강제진동시험의 결과에 대해 보고한다. 또한 저항복점강재의 지진에너지 소산양의 정량적인 평가를 위하여 수학적 이력형모델 및 등가선형해석법을 이용하여 평가한 결과에 대해 보고한다.
최근 구조물 진동제어 연구분야에서는 반능동형 진동제어(제진)장치어 대한 연구가 활발하게 진행되고 있다. 반능동형 제진장치는 수동형의 장점인 신뢰성과 경제성 및 능동형의 장점인 적용성(순응성)을 얻을 수 있기 때문이다. 본 연구에서는 반능동형 제진장치의 일종으로 2톤급 반능동형 오리피스 유체댐퍼를 설계ㆍ제작하여 구조물의 적용을 통해 성능을 검증하였다. 수동형 오리피스 유체댐퍼에 2단 솔레노이드 밸브를 설치하여 반능동형을 구현하였다. 단독 성능시험을 통해 동특성을 파악하고, 시험용 철골구조물 적용시험을 통해 외부하중을 받는 구조물의 진동제어용 장치로서의 가능성을 확인하였다.
본 연구에서는 구조가 간단하고 경제적이며, 보수유지 면에서 능동형 진동제어 장치로서 매우 유리한 장점을 가지고 있는 선형모터 댐퍼(LMD : linear motor damper)를 개발하여 유니슨 기술연구소에 설치된 대형 철골구조물에 적용하였다. 개발된 LMD는 1,500kg의 가동질량을 갖고 있으며, 최대 \pm250mm의 변위로 움직일 수 있다. 제어 대상 시험구조물의 최저차 2개 진동형만을 가지는 축소모델을 사용하여 H_{\infty} 제어로직을 설계하였다. 일련의 성능 검증시험을 통해 시험 구조물의 1, 2차 진동형에 대해 가속도 레벨이 약 l0dB 감소함을 확인하였다. 본 연구를 통해 개발된 LMD가 풍 및 지진하중을 받는 구조물의 진동제어용 제진장치로서 가능성이 있음을 확인하였다.
Coal-fired thermal power generation was a very important power source in Korea. Therefore improvement of seismic reliability of the coal-fired thermal power plants is required, because occurrence of very large earthquakes is expected in Korea. Boilers of coal-fired power plants are usually suspended from the upper end of support structures in order to allow thermal expansion of the boilers, so boilers easily sway during earthquakes. In order to suppress the vibration, stoppers made of steel are generally installed between boilers and their support structures. Although stoppers made of steel are effective for vibration suppression, further countermeasure for earthquakes having long duration and many after shocks is required. This study has developed a hybrid damper for vibration and seismic control of coal-fired power plant boiler. The hybrid damper consists of an oil damper and a friction damper connected in series.
Recently many investigations have been conducted to evaluate and analyze the seismic response of structures equipped different types of damper. Viscous dampers are known as effective energy dissipation devices improving structural response to earthquakes. The damping force developed by the viscous damper depends on internal structural system and the physical properties of the fluid used in the device. This study has developed a viscous damper for vibration and seismic control of structures. In order to verify the performance of a viscous damper, experimental tests were performed.
This study focus on Perimeter Concrete Wall Dampers (PCWD). PCWD can achieve required large mass ratio without additional mass. This system also can control multimode vibration. Suitable location for the installation of PCWD and their tuning frequencies are selected based on modal parameters of the uncontrolled structure respectively. In addition to the numerical simulation, an eleven story is modeled using SAP2000. The proposed system is greatly reducing seismic response of main structure.
In this dissertation, experimental study about the real-time vibration control of the bridge structure was conducted by using the semi-active vibration control method that has been in the spotlight recently. Based on the laboratory-scale bridge model in the form of the cable-stayed bridge, the shear type MR damper and the semi-active vibration control algorithm (Lyapunov and Clipped-optimal) were applied in order to the control the harmful vibration in real time. From the investigation of the test results, the performance of each semi-active control algorithm was evaluated quantitatively.
본 논문에서는 구조적으로 유연한 특성을 갖는 교량 구조물을 대상으로 외력에 의해 발생되는 진동을 실시간으로 제어하고자 실험적 연구를 수행하였다. 여기서 진동제어를 위한 교량 구조물은 서해대교를 규모화 한 모형 교량 구조물을 사용하였고, 실험실 여건을 고려해 규모화 된 El-centro 지진파형으로 구조물을 가진하였다. 또한, 교량 상판 중앙지점에는 전자석이 채용된 전단형 MR 댐퍼를 설치하여 발생된 진동을 제어하도록 하였고, 동시에 변위계 및 가속도계를 설치하여 구조물의 응답(변위, 가속도)을 획득하였다. 이때 진동제어의 실험은 크게 비-제어, 수동 on/off 제어, 그리고 Lyapunov 안정도 이론에 의한 실시간 피드백 진동제어방법을 이용하여 수행하였고, 이때 진동제어의 효과는 상판 중앙지점에 대하여 비-제어 시 기준 각 실험방법 별 절대최대변위와 절대최대가속도 그리고, 인가전압의 소모량으로 평가하였다. 진동제어실험의 결과로부터, Lyapunov 제어방법은 구조물의 발생 변위 및 가속도를 효과적으로 감소시켰으며, 특히 진동제어 시 요구되는 외부 인가전압의 소비를 크게 감소시킬 수 있음을 확인하였다. 최종적으로, 본 논문에서 구성한 실시간 준능동 피드백 진동제어 시스템은 구조물에 발생된 진동을 제어․관리하기 위한 적극․ 효율적인 방법으로 활용될 수 있는 가능성을 제시하였다.