PURPOSES : The purpose of this study is to investigate the tendency of material property estimation under different concrete distress conditions and curling conditions when non-destructive tests such as rebound hammer and surface deflection test are applied to concrete pavement. METHODS : Nondestructive tests using Schmidt hammer and Falling Weight Deflectometer were performed to inspect the expressway concrete pavements constructed more than 20 years ago. Some results were compared with core tested elastic modulus and compressive strength. RESULTS : As a result of the rebound test, the section with Alkali-Silica Reaction(ASR) distress was outside the range of the existing estimation formula, but the control section was found to be within the range of the existing estimation formula. As a result of the physical property estimation through deflection test, the section with ASR distress showed greater fluctuations in the estimated material properties and deflection ratio compared to the control section, showing that the ASR damage seems to affect the slab deflection behavior. CONCLUSIONS : The rebound test may not sufficiently reflect the decline in material properties due to concrete damage. The deflection test can obtain results that reflect the deterioration of material properties, but it was confirmed that significant variability may occur, so it seems to necessary to perform complementary indoor core tests with nondestructive testing(NDT) tests.

The air dilution olfactory method to measure complex odors needs to store and carry odor samples from the field sampling until the analysis in laboratories. Until the analysis of sample in the laboratory, odor dilution factor (odor sensitivity) in the sample bag may decrease over time depending on the characteristics of each odor substances. This is one of the limitation for the air dilution olfactory method. Thus, the air dilution device enable to measure without loss in complex odors of samples. Recently, many studies on the performance test of on-site air dilution devices, i.e., field olfactometer, has been conducted to figure out the feasibility of the field olfactometers. In this study, seven odor samples were collected from five odor emission source sites. And comparative analysis with the air dilution olfactory method was carried out to assess the field applicability of the olfactometer. As results, the performance of the field olfactometer used in this study is regared as the affordable method. The dilution factors from between two methods showed the similar values, indicating low values of standard deviations. In order to ensure the accuracy and precision of measurement data using the field olfactometer, methodology minimized variables (that may affect measurement) needs to establish.

PURPOSES : This study investigated the field applicability of pervious concrete to pavement base courses. Pervious concrete was developed at laboratory level, and the compaction methods, field moisture content, and fundamental properties when the material was constructed in the field were studied. METHODS : Field-applied pervious concrete was compacted at different levels using a tandem roller, and cores were taken to investigate the compressive strength, infiltration rate, continued porosity, and freeze-thaw resistance. In addition, the optimum field construction and quality control of the moisture content of a batch plant were measured. RESULTS : The moisture content of pervious concrete has an essential effect on workability and quality control during field test construction. From the test herein, the optimum value at a batch plant was found to be approximately 2.5±0.1%. The compaction level is also a crucial parameter at construction sites because it affects the mechanical and penetration properties. Considering both compressive strength and drainage, the recommended compaction was three times the round trip when a tandem roller was used. The penetration coefficient was 0.88 cm/sec when applying three times the round trip of the tandem roller. The freezing and thawing weight loss rates of the applied pervious concrete satisfied the required condition of 14% or less, regardless the compaction level. CONCLUSIONS : With the suggested mixed proportions of pervious concrete, the recommended compaction was three times the round trip of a tandem roller and a moisture content of approximately 2.5±0.1% from a batch plant. When these conditions were satisfied, the mechanical and drainage properties satisfied the required criteria.

본 연구는 뷰티산업 현장 실무 전문가를 양성하기 위한 피부미용 이론 및 실기 수업을 통해 문 제중심학습(PBL) 수업 개발 및 적용하고자 한다. 학습자들에게 피부미용 현장에서 일어나는 실제적인 문제 를 제시하고, 그 문제를 해결하기 위해 학습자들 상호간에 공동으로 문제를 해결하는 방안을 강구하고자 한다. 학습자들에게 문제중심학습(PBL)을 적용한 피부미용 수업을 진행하고, 수강 후 그 효과에 대해 분석 한다. 본 연구 결과로 현장 실제의 문제를 제시함으로써 학습자들이 실제 전문가들이 하는 일을 이해할 수 있었고, 주어진 문제에 대한 다양한 해결방법을 도출할 수 있다는 부분을 알게 되었다고 하여 문제해결 능 력 신장을 기대 해 볼 수 있었다. 이와 같은 결과는 문제 탐구와 문제를 해결하기 위한 문제중심학습(PBL) 수업 과정은 학습자의 문제해결능력 향상에 긍정적으로 작용하고 있음을 시사하고 있다.

국내 Y정수처리시설에 20-40 m3/m2/h의 표면부하율을 갖는 고속 용존공기부상공정을 도입하였다. 우선, 용존공기부상공정과 입상활성탄 공정이 결합된 반응기를 일처리용량 500 m3/day의 조건으로 운전하였다. 운전결과는 두 공정이 원수내 탁도, 조류, 지오스민, 2-MIB를 감소시킬 수 있음을 증명하였다. 도출된 최적 설계요소를 활용하여 현장규모의 공정(5,000 m3/day)에 용존공기부상공정을 도입하였다. 여름철 56일간 조류와 탁도 제거율을 평가하였다. 처리수 내 조류의 개체수는 20-30 cells/mL 이하로 유지되었으며, 조류 제거효율은 80-89%를 기록하였다. 침전법 및 용존공기부상공정 처리수질의 탁도 제거효율을 비교한 결과 평균 탁도 제거효율은 77%를 나타냈다. 이러한 결과들은 고속 용존공기부상공정이 여름철 음용수의 탁도 및 조류와 같은 저밀도 고형물을 제거하는데 유의미한 방법임을 나타냈으며, GAC는 맛･냄새를 유발하는 화합물(지오스민, 2-MIB)를 제거할 수 있는 공정 옵션인 것을 확인하였다.

PURPOSES : The objective of this study is to present a practical application method for measuring the setting time of concrete in the field, considering different concrete blending and curing environments. METHODS : In the experimental environment of the concrete setting experiment, a mold was made in the laboratory, and the curing temperature was performed at laboratory room temperature (20-25 ℃), heater (30 ℃), and dryer (40 ℃). In the field, the experimental method was performed in summer and autumn, setting experiments on penetration resistance, ultrasonic pulse velocity, and semi-calorimeter. RESULTS : The result of the concrete setting time experiment was that the early setting time was achieved in the combination of filash and slag when the concrete was mixed, and the setting time in the curing environment was the same as the early setting time in the field. The setting time measurement method shows the correlation of the high crystal coefficient at UPV with 0.99 based on PR and the good ratio of 92 % to 107 % on average. In addition, the semi-calorimeter shows a good crystal coefficient of 0.96 to 0.99 and a good setting time of 88 % to 101 % on average. CONCLUSIONS : The analysis of the setting time of the concrete shows that the curing temperature is more affected than the mixture, and it is considered that the UPV test, which evaluates the reliability of the degree of purification, is easy to sampie among the three methods.