본 연구는 냉각코일과 리튬브로마이드 수용액을 활용 하여 유리 chamber 내 냉각 및 제습 실험을 수행하였다. 냉각수 온도별 냉각 효과와 리튬브로마이드 수용액의 제습량을 확인하였으며, 이를 동시에 적용하여 실험을 수행하였다. 냉각수 온도별 냉각 실험은 279K, 286K, 293K에서 각각 19K, 13K, 10K 가량 감소되는 경향을 보였다. 냉각수 온도가 낮을수록 높은 냉각 성능을 보였으며, 여름철 상하수도 온도인 293K의 물로도 충분히 작물이 생육하기 좋은 온실 내부온도를 유지할 수 있다고 판단되었다. 또한 리튬브로마이드 수용액을 활용한 제습 실험에서는 약 80%의 외부 습도가 리튬브로마이드 수용액과 결합하여 약 50%로 감소되어 약 30%의 제습량을 보였으며, 이는 시설 내 제습 시스템의 적용에 적합한 물질로 판단된다. 냉각코일과 리튬브로마이드 수용액을 동시에 적용한 실험에서 약 9K의 온도 강하, 15%의 제습량을 나타냈으며, 리튬브로마이드 수용액이 수증기를 흡수하는 과정에서 반응열이 발생하는 것을 확인하였다. 또한, 시뮬레이션을 통해 냉각 실험 결과와 대비 비교 한 결과 약 299.7K의 내부 온도를 보여 일치하는 것을 확인하였다. 수분의 제습과정을 거치면서 농도가 낮아진 리튬브로 마이드 수용액(희용액)은 수집탱크로 모아 재생부로 이송되어 가열, 수분을 증발시켜 농용액으로 전환된 후 열 교환을 거쳐 냉각되어 다시 제습시스템으로 공급되는 시스템을 적용하면 일정량의 리튬브로마이드 수용액만으로 온실 제습을 할 수 있을 것으로 판단된다. 본 실험을 통해 냉각 및 제습이 동시에 가능하다는 것을 확인하였으며, 리튬브로마이드 수용액을 활용하여 실제 온실에 적용된다면 기존 온실에서 사용하고 있는 냉방 및 제습 방법에 비해 에너지 절감을 통한 경제적 효과를 얻을 수 있을 것으로 판단된다. 향후, 제습 부분은 시뮬레이션을 통한 분석 및 실험결과와 대비 검증이 요구되고, Lab scale의 제습 시스템에 서 Farm scale의 온실 규모로 확장하여, 추가 변수에 대한 제습 및 냉각 연구가 수행되어야 할 것이다.

This research is to investigate the cooling performance analysis of the heat sinks for LED light with four different fin types and two different fin numbers (16EA and 64EA) of heat sinks. Temperature distributions of fins over the flow domain are numerically calculated for the optimum design of heat sink fin types with uniform initial temperature of the bottom of the fins. According to the calculations of convective heat transfer coefficient between fin and atmosphere in the flow domain, S-curve fin type of heat sinks with 64EA of fins reveals the highest cooling performance of the heat sink fin types in the present cooling heat sink model.

This experiment evaluated the interaction effect of extreme heat diet(EHD), inverse lighting, and cool water on the growth performance of broiler chickens under extreme heat stress. There were 4 experimental groups (T1: EHD 1, 10:00-19:00 dark, 19:00-10:00 light, cold water 9℃; T2: EHD 2, 10:00-19:00 dark, 19:00-10:00 light, cold water 9℃; T3: EHD 1, 09:00-18:00 dark, 18:00-09:00 light, cold water 14℃; T4: EHD 2, 09:00-18:00 dark, 18:00-09:00 light, cold water 14℃), each group composed of 25 broilers and the experiment was repeated 3 times. EHD 1 contained soybean oil, molasses, methionine and lysine. EHD 2 contained all nutrients of EHD 1 and vitamin C additionally. As a result, T1 and T2 displayed higher body weight increase and diet intake compared to T3 and T4 (p<0.05). The weights of their liver and gizzard were similar but the weights of the thymus and bursa F were higher for T1 and T2 compared to that of T3 and T4 (p<0.05). It was observed that T1 and T2 displayed higher concentrations of blood triglyceride, total cholesterol, HDL-C and blood sugar compared to that of T3 and T4 but LDL-C level was higher for T3 and T4 compared to that of T1 and T2 (p<0.05). T1 and T2 displayed higher levels of immunity substances such as IgG, IgA and IgM compared to T3 and T4 but the blood level of corticosterone displayed to be lower for T1 and T2 compared to T3 and T4 (p<0.05). The T1 and T2 contained a higher amount of fecal lactobacillus compared to that of T3 and T4 but the T3 and T4 contained a higher amount of fecal E. coli, total aerobic bacteria, coliform bacteria compared o that of T1 and T2 (p<0.05). T1 and T2 displayed higher concentrations of cecal acetic acid, ropionic acid and total short chain fatty acids compared to T3 and T4 but T3 and T4 displayed igher concentrations of butyric acid, isobutyric acid, valeric acid and isovaleric acid compared to T1 and T2 (p<0.05). These results have been observed that broiler chickens exposed to extreme eat stress with feeding EHD, inverse lighting and cold water would improve blood lipid, and elevate the production of immunity substance, beneficial microorganisms, and short chain fatty acids. This provision would also reduce the blood sugar consumption rate as energy sources and these effects will improve the growth performance of the broilers exposed to extreme heat.

The purpose of this study is to present a case study of six sigma quality improvement practice in cooling fan motor(CFM) manufacturing processes. In this study, the CFM manufacturing process of automobile parts not relevant to the target process rate of the process point of view, in order to reduce the system to solve the problem of localized resolution procedures of six sigma DMAIC methodology was applied to study. In conclusion , this study 's field D in order to improve the initial rate of inadequate quality management best practices by applying the method of Six Sigma quality CFM failure through stabilization schemes were proposed cost reduction .To be CFM product to satisfy customers based on continuous monitoring of the effective field of claims quality management system is required.

A three dimensional numerical analysis was performed to study the cooling performance of xEV battery module depending on cooling fluid inlet position. Depending on the inlet position from the top, case 1 (top inlet), case 2 (middle inlet), and case 3 (bottom inlet) are selected. For the case 1, the temperature of the battery near inlet was higher than that of the battery near outlet. For the case 2 and 3 the temperature of the battery near inlet was lower than that of the battery near outlet. From the analysis result, the cooling performance is higher in the order of case 2, case 3, and case 1.

This analytical work was performed to reveal the effect of inlet geometry of battery pack on the temperature distributions and flow stream line for a electric vehicle. To achieve this, standard k-ε model with wall function was applied and the working conditions of battery pack under different air flow rate and inlet area according to the geometry were estimated. It was revealed that as inlet area was smaller, the flow velocity was faster, and it can't cover the whole area of battery module. In case of two inlet case, the cooling efficiency of air flow is less than that of one inlet case because of low flow rate.

This study investigated the continuous cooling transformation, microstructure, and mechanical properties of highstrength low-alloy steels containing B and Cu. Continuous cooling transformation diagrams under non-deformed and deformed conditions were constructed by means of dilatometry, metallographic methods, and hardness data. Based on the continuous cooling transformation behaviors, six kinds of steel specimens with different B and Cu contents were fabricated by a thermomechanical control process comprising controlled rolling and accelerated cooling. Then, tensile and Charpy impact tests were conducted to examine the correlation of the microstructure with mechanical properties. Deformation in the austenite region promoted the formation of quasi-polygonal ferrite and granular bainite with a significant increase in transformation start temperatures. The mechanical test results indicate that the B-added steel specimens had higher strength and lower upper-shelf energy than the B-free steel specimens without deterioration in low-temperature toughness because their microstructures were mostly composed of lower bainite and lath martensite with a small amount of degenerate upper bainite. On the other hand, the increase of Cu content from 0.5 wt.% to 1.5 wt.% noticeably increased yield and tensile strengths by 100 MPa without loss of ductility, which may be attributed to the enhanced solid solution hardening and precipitation hardening resulting from veryfine Cu precipitates formed during accelerated cooling.

A cooling system that applies impinging jet is studied. To create a jet, a square edge type nozzle is used as its shape. The impinging jet that composes a cooling system which applies impinging jet is created in the nozzle plate that correspond to each LED where the cooling area exists. The distance(d) between the nozzle plate and LED plate with heat sink is where the LED light is established. The main variation and the standard is examined for four different cases through the way out diameter of nozzle plate exit(D). The examined velocity distribution and temperature distribution about the impinging jet cooling system consisted of nozzle plate. It was found that an individual LED consisting of nozzle plate was efficient.

This paper presents that hybrid cooler of vapor compression type and natural refrigerant circulation type is energy saving cooler using R-410a for indoor mobile telecommunication station. Its performance and operation characterists are done experimently about receiver tank, piping and heat exchanger designs for natural circulation of refrigeration and use of R-410a for fixed height location difference of indoor and outdoor cooler.

LEDs are increasingly used for many applications including automotive, display and special lighting applications. The performance and lighting characteristics of the LED depend on cooling condition because the power LED generates lots of heat. In this study, the effect of the generated heat from power LED module on cooling characteristics and performance is measured and evaluated. For experiments, the transient temperature of a power LED module with cooling condition is measured.

The temperature distribution of a generic battery module was analyzed for different flow rates of cooling fluid. For the given battery module design, the temperature of battery cell near the inlet is higher than that of battery cell near the outlet. Because the inlet is located at the higher elevation than the top of battery electrodes, most of the incoming cooling fluid flows directly towards the battery housing wall above the outlet. For the inlet velocities of 1, 3, 5 m/s, the maximum temperature differences are 28, 19, 15 degrees Celcius respectively.

This experimental study was investigated the flow characteristics around staggered cooling tube arrays. A particle image velocimetry technique was employed to obtain detailed measurements at inlet-velocity-based three Reynolds numbers and the frequency characteristics of the wake were analyzed by using spectral analysis of the measured wake velocity signals. As a results, the flow exhibits strong Reynolds number dependence in the developing region but no significant Reynolds number effects are observed in the spatially periodic region.