본 연구는 미국의 동아시아 안보전략과 해외주둔군 전략, 확장억제전 략의 변화를 분석하고, 북한의 핵무기 고도화에 대비한 주한미군과 핵우 산 정책을 고찰한다. 한미동맹이 체결된 1953년 이후, 미국은 한반도 안 보의 중심 역할을 수행했으나 비대칭 동맹으로 인한 동맹 딜레마와 미군 의 역할 및 규모 변화가 발생했다. 핵우산 정책은 냉전기 소련의 핵전술 에 대항하여 확장되어 현재까지 적용되고 있으며, 2023년에는 워싱턴 선 언을 통해 한미 핵협의그룹(NCG)이 창설되었다. 이를 통해 상시적인 확 장억제가 논의되고 있으며, 굳건한 한미 동맹체제와 안보공약이 SCM을 통해 재확인되었다. 이제는 냉전 시기의 미군 주둔과 자동개입 문제는 중국의 G2국가 발전, 북한의 핵과 미사일 도발 등으로 시대적 변수가 달 라져 있다. 따라서 미국의 주한미군 정책, 개입 문제, 확장억제전략에 대 한 신중한 검토와 대비가 필요하다. 본 연구는 미국의 동아시아 전략, 주 한미군, 확장억제전략에 대해 고찰하고 한반도 안보에 대한 전망을 목적 으로 한다.

In this study, we examined dimensional changes in processing carbon fiber composites using a cost-competitive domestic high-speed router. Lacking temperature compensation features found in typical machines, it faces increased defect rates due to temperature fluctuations during processing. To mitigate this, we defined specific processing temperature conditions, established hole positions as distance references for various temperatures, and measured dimensional changes. This enabled us to calculate necessary dimensional corrections, minimizing thermal deformation.

Prepreg is an abbreviation of Preimpregnated Materials. It is a sheet-type product in which a matrix is ​​impregnated with reinforced fiber. The prepreg has very different properties depending on the orientation of the fibers and the weaving method, and the orientation of the fibers plays an important role in determining the mechanical strength of CFRP. Short and randomly oriented reinforcing fibers show isotropy, while long, unidirectional reinforcing fibers exhibit anisotropic behavior and are strongest when the applied load is parallel to the reinforcing fibers. Classification by the direction of the fiber is divided into unidirectional, orthogonal, multiaxial, and the like. Uni-directional refers to a state in which almost all fibers in the fabric are aligned in one direction. When the fibers used as reinforcing materials are aligned in one direction, the fibers are used in a straight line without twisting during the fabric production process, and there is an advantage in that the amount of fibers used as a whole can be minimized. A uni-directional prepreg exhibits different cutting forces depending on the stacking orientation angle. In this experiment, the optimal cutting conditions for a uni-directional prepreg 45 degree orientation angle specimen are presented.

In the context of the 4th Industrial Revolution, the rise of electric vehicles and personal mobility is evident. However, regulatory authorities seem to overlook vast opportunities, placing two-wheelers in a deregulated category and focusing mainly on regulations. This paper addresses a notable trend in e-mobility, emphasizing aspects often overlooked in traditional motorcycle regulatory research. Using the industrial life cycle theory as a basis, we identify challenges that have affected traditional combustion-engine two-wheelers and offer insights to navigate similar obstacles in the future. Consequently, the domestic two-wheeler market experienced a brief surge but lacked sustainable growth prospects. However, considering Japan's success in establishing global standards and design dominance in the two-wheeler industry despite its late entry, there appears to be potential for a rebound in the domestic market.

During the initial construction of Won buddhism, the sound absorbing material and diffusion material were used in the interior of the Won buddhism, so the sound performance at each buddhism could not be secured above a certain level, and even in the case of the Won buddhism Bukil dharma hall, the reverberation and volume of the sound generated inside the sanctum was too loud, and since the establishment of the buddhism continued to be dissatisfied, the improvement of the acoustic performance was very urgent. From this perspective, this study measured acoustic performance of the Bukil dharma hall before remodeling, determined the acoustic defects and status, and used acoustic simulation to present three plans for improving acoustic performance. Taking economic feasibility, construction, and construction duration into account, remodeling was performed on the basis of Plan 1 and post-remodeling acoustic performance was measured for comparative analysis of acoustic performance between before and after the improvement. The results of study, before and after sound performance improvement sound pressure level (SPL500Hz) was 71.9dB at 79.4dB , the weighted sound level (SPLdB(A)) was 79.7dB(A) at 89.4dB(A), reverberation time (RT500Hz) was 1.12sec at 1.49sec, early decay time (EDT500Hz) was 1.39sec at 1.63sec, definition (D50,500Hz) was 34.9% at 32.3%, clarity (C80.500Hz) was 1.0dB at –0.4dB, and RASTI was 60.0%(“Good”) at 51.3%(“Fair”) was evaluated. Therefore, the Bukil dharma hall was after remodeling, neither definition(D50) improved notably but excessive volume and reverberation and sound mixing almost disappeared and acoustic performance improved so much that many different events and services could be held.

The need for lightweight yet strong materials is being demanded in all industries. Carbon fiber-reinforced plastic is a material with increased strength by attaching carbon fiber to plastic, and is widely used in the aerospace industry, ships, automobiles, and civil engineering based on its low density. Carbon-reinforced fiber plastic is a material widely used in parts and manufactured products, and structural analysis simulation is required during design, and application of actual material properties is necessary for accurate structural analysis simulation. In the case of carbon-reinforced fiber plastics, it is reported that there is a porosity of around 0.5% to 6%, and it is necessary to check the change in material properties according to the porosity and pore shape. It was confirmed by applying the method. It was confirmed that the change in elastic modulus according to the porosity was 10.7% different from the base material when the porosity was 6.0%, and the Poisson's ratio was confirmed to be less than 3.0%. It was confirmed that the elliptical spherical pore derived different material properties from the spherical pore depending on the pore shape, and it was confirmed that the shape of the pore had to be confirmed to derive equivalent material properties.

In this study, numerical analysis was performed for the purpose of analyzing the flow characteristics and performance according to the change in the inflow hydrogen temperature and differential pressure of the receptacle of the hydrogen charging system. The pressure distribution and turbulent kinetic energy in the filter area were analyzed by changing the outlet pressure condition under the inlet hydrogen temperature condition, and the flow velocity change at the outlet was compared and analyzed. As a result of the analysis, as the differential pressure decreased, the flow rate at the outlet of the receptacle decreased by up to about 70% at the 2.86 MPa condition compared to the 1.86 MPa condition, and the mass flow rate decreased by about 56.5% at the maximum. It was found that the standard CV performance was not satisfied when the differential pressure at the inlet and outlet was 1.12 MPa or less under the 363K temperature condition.

This study aimed to assess and determine the optimal model for predicting the full bloom date of ‘Fuji’ apples across South Korea. We evaluated the performance of four distinct models: the Development Rate Model (DVR)1, DVR2, the Chill Days (CD) model, and a sequentially integrated approach that combined the Dynamic model (DM) and the Growing Degree Hours (GDH) model. The full bloom dates and air temperatures were collected over a three-year period from six orchards located in the major apple production regions of South Korea: Pocheon, Hwaseong, Geochang, Cheongsong, Gunwi, and Chungju. Among these models, the one that combined DM for calculating chilling accumulation and the GDH model for estimating heat accumulation in sequence demonstrated the most accurate predictive performance, in contrast to the CD model that exhibited the lowest predictive precision. Furthermore, the DVR1 model exhibited an underestimation error at orchard located in Hwaseong. It projected a faster progression of the full bloom dates than the actual observations. This area is characterized by minimal diurnal temperature ranges, where the daily minimum temperature is high and the daily maximum temperature is relatively low. Therefore, to achieve a comprehensive prediction of the blooming date of ‘Fuji’ apples across South Korea, it is recommended to integrate a DM model for calculating the necessary chilling accumulation to break dormancy with a GDH model for estimating the requisite heat accumulation for flowering after dormancy release. This results in a combined DM+GDH model recognized as the most effective approach. However, further data collection and evaluation from different regions are needed to further refine its accuracy and applicability.

This study was conducted to determine the optimal irrigation starting point by analyzing tree growth, physiological responses, fruit quality, and productivity in peach orchards. Seven-year-old ‘Kawanakajima Hakuto’ peach trees were used in an experimental field (35°49′30.4″N, 127°01′33.2″E) located within the National Institute of Horticultural and Herbal Science located in Wanju-gun, Jeollabuk-do. The irrigation starting point was set with four levels of –20, –40, –60, and –80 kPa from June to September 2022. While there were no significant differences in increase of trunk cross-section area and leaf area among treatments, shoot length and diameter decreased in the –80 kPa and –20 kPa treatments. The photosynthetic rate measured in August was highest for –60 kPa (17.7 μmol·m-2·s-1), followed by –40 kPa (15.6 μmol·m-2·s-1), –20 kPa (14.5 μmol·m-2·s-1) and –80 kPa (14.0 μmol·m-2·s-1). SPAD value measured in May and August was lower in the –80 kPa and –20 kPa treatments than in the –60 kPa and –40 kPa treatments. The harvest date reached three days earlier in the –20 kPa treatment compared to other treatments. The fruit weight was highest in the –60 kPa (379.1 g), followed by –40 kPa (344.0 g), –80 kPa (321.0 g) and –20 kPa (274.9 g). Firmness was the lowest in the –20 kPa treatment. The soluble solid content was highest in the –60 kPa treatment (13.3°Bx).The ratio of marketable fruits was highest in the –60 kPa treatment (50.7%) and lowest in the –80 kPa treatment (23.4%). In conclusion, we suggest that setting the irrigation starting point at –60 kPa could improve the fruit quality and yield in peach orchards.

In this study, the effect of crown heating on the cultivation environment, budding, flowering and yields of strawberry was analyzed. In December, January, and February, when the outside temperature was low, the average strawberry crown temperature at daytime in the test zone was 1.3°C higher than that in the control zone, and the average strawberry crown temperature at nighttime in the test zone was 2.7°C higher than that in the control zone. The average bed temperature at daytime in test zone was 1.7°C higher than that in the control zone, and the average bed temperature at nighttime in test zone was 2.4°C higher than that in the control zone. As a result of performing correlation analysis and regression analysis on strawberry crown temperature and budding period, the correlation coefficient was -0.86, which tended to be shorter as the crown temperature was higher, and the determination coefficient was 0.74. The total yields of strawberry during test period were 392.6 g/plant for test greenhouse and 346.0 g/plant for control greenhouse respectively. As for the quality of strawberries, the ratio of 2L (very large) grades and L (large) grades was 62.4% in the test greenhouse and 58.5% in the control greenhouse, indicating that the proportion of high quality strawberries was higher in the test greenhouse.

As the consumption of corn increases, the production of by-products is also increasing. In this study, functional substances and antioxidant activities of corn by-products were investigated to determine their applicability as functional materials. Total polyphenol, flavonoid contents, and ABTS antioxidant activity were the highest in leaves. The total phenolic acid content was the highest in cobs; p-coumaric and ferulic acid were the main components. Phytosterol content in leaves and stems was high at 64 and 50 days after sowing, 261.4 and 274.7 mg/100 g, respectively. β-sitosterol of the leaves and stems was the highest, 149.2 and 138.7 mg/100 g. The total phytosterol content of grains and by-products harvested 106 days after sowing was in the order of: corn silk, husk, grain, leaf, stem, and cob. Among the phytosterols, β-sitosterol was the highest, followed by stigmasterol and campesterol, and the composition was different depending on part. The total phytosterol content was the highest in husk and corn silk, but the stems and leaves, which account for 50% of the total corn biomass, also contained high phytosterol content. Therefore, corn leaves and stems are expected to be used as functional raw materials for the development of functional materials in the future.

Changes in contents of free sugars, amino acids, and fatty acids of legumes were analyzed for each phase of in vitro digestion. In addition, contents of resistant starch in raw and digested pulses were compared. Soybeans, kidney beans, cowpeas, and chickpeas were analyzed. An in vitro digestion model was used to analyze contents of nutrients using LC-MS and GC-MS. Stachyose in kidneybean, cowpea, and chickpea increased as the digestion phase progressed. In four types of legumes, raffinose slightly decreased or showed no significant difference between the Oral phase and the BBMV phase. Content of glucose, a monosaccharide, increased during the BBMV phase. During the digestion phase, levels of free amino acids and free fatty acids also increased. Content of resistant starch was reduced compared to that in the raw material. It was 0.01g/100 g food in soybean, 1.06 g/100 g food in red kidney bean, 0.77g/ 100g food in cowpea, and 0.76 g/100 g food in chickpea. It was confirmed that nutrients in the in vitro digestion model were liberated at each digestion phase with changes in the content of resistant starch. These results are expected to be used as fundamental data for obtaining bioavailability of nutrients.

이 연구는 임도 개설 전·후 년차별로 식물상과 식생의 변화를 분석하고 관리 방안을 제공하기 위하여 전북 무주군 설천면 미천리에 소재한 민주지산 임도를 대상으로 임도 개설 전년도인 2012년부터 임도 개설 후 2022년까지 7차례에 걸쳐 수행되었 다. 임도 개설 조사구간 내의 식물군락은 북서사면에서 신갈나무군락, 남서사면에서 굴참나무군락과 일본잎갈나무군락으로 구분되어 남서사면과 북서사면에서 군락의 차이를 보였다. 임도 개설 전·후 년차별로 식물상의 변화는 임도 개설 전인 2012년 도 총 66분류군(44과 59속 51종 13변종 2품종)에서 2015년도에는 207분류군(71과 153속 176종 27변종 4품종)으로 141분 류군이 증가하였고, 2022년도에는 278분류군(78과 172속 242종 1아종, 31변종 4품종)으로 212분류군이 증가하였다. 특히 임도절토사면과 임도연접사면부의 조사구에서는 년차적으로 높은 식피율과 새로운 분류군의 증가를 보였는데, 이는 임도 개설에 따른 광량의 급격한 증가와 귀화식물 및 1년생 초본류의 유입으로 인해 일어난 현상으로 사료된다. 임도 개설 10년후 연차적으로 조사된 식생 조사 결과를 보면, 임도 개설 초년도에는 식피율과 종수가 빠른 속도로 증가하다가 일정 기간이 경과 하면 식피율과 출현 종수는 줄어들고 안정된 숲이 형성되어 우점종의 비율이 증가하였다. 특히 임도연접사면에서 관목층 과 초본층을 살펴보면, 임도 개설 직후 몇 년간은 초본층의 식피율이 현저히 증가하다가 시간이 경과 할수록 초본층의 피도는 감소하고, 관목층의 피도가 현저히 증가하였다. 그리고 임도산지사면에서는 초본층과 관목층의 피도는 현저히 감소하고, 아교목층과 교목층의 피도가 증가하였다.

The major active components of Astragalus membranaceus (AM) are isoflavones, which exist in the form of various glycosides. Nuruk is a traditional fermentation starter in Korea, and is suitable for the biotransformation of isoflavone glycosides because it contains various microorganisms and enzymes. This study was performed to determine changes in the isoflavones and antioxidant properties of AM fermented (AF) with nuruk over 24 hours. AF was sampled after 0, 2, 4, 6, 12, 18, and 24 h of fermentation, and calycosin 7-glucoside, ononin, calycosin, and formononetin content, and the antioxidant properties of AF were analyzed. The total phenolic content increased with fermentation time, and the ABTS radical scavenging activity increased until 6 h of fermentation and then decreased. During fermentation, the isoflavone glycosides decreased significantly as fermentation time increased. The contents of calycosin and formononetin, which are aglycons of calycosin-7-glucoside and ononin, increased from 100.54 μg/g to 276.84 μg/g and from 56.29 μg/g to 123.04 μg/g, respectively, at 18 h of fermentation. Significant correlations were observed between fermentation time, isoflavone content, and antioxidant properties. The results of this study showed that fermentation with nuruk is suitable for the biotransformation of isoflavones in AM.

Ultra-violet (UV) light is one of abiotic stress factors and causes oxidative stress in plants, but a suitable level of UV radiation can be used to enhance the phytochemical content of plants. The accumulation of antioxidant phenolic compounds in UV-exposed plants may vary depending on the conditions of plant (species, cultivar, age, etc.) and UV (wavelength, energy, irradiation period, etc.). To date, however, little research has been conducted on how leaf thickness affects the pattern of phytochemical accumulation. In this study, we conducted an experiment to find out how the antioxidant phenolic content of kale (Brassica oleracea var. acephala) leaves with different thicknesses react to UV-A light. Kale seedlings were grown in a controlled growth chamber for four weeks under the following conditions: 20°C temperature, 60% relative humidity, 12-hour photoperiod, light source (fluorescent lamp), and photosynthetic photon flux density of 121±10 μmol m-2 s-1. The kale plants were then transferred to two chambers with different CO2 concentrations (382±3.2 and 1,027±11.7 μmol mol-1), and grown for 10 days. After then, each group of kale plants were subjected to UV-A LED (275+285 nm at peak wavelength) light of 25.4 W m-2 for 5 days. As a result, when kale plants with thickened leaves from treatment with high CO2 were exposed to UV-A, they had lower UV sensitivity than thinner leaves. The Fv/Fm (maximum quantum yield on photosystem II) in the leaves of kale exposed to UV-A in a low-concentration CO2 environment decreased abruptly and significantly immediately after UV treatment, but not in kale leaves exposed to UV-A in a high-concentration CO2 environment. The accumulation pattern of total phenolic content, antioxidant capacity and individual phenolic compounds varied according to leaf thickness. In conclusion, this experiment suggests that the UV intensity should vary based on the leaf thickness (age etc.) during UV treatment for phytochemical enhancement.