본 연구의 목적은 재료분야 국내 공동특허의 공동 출원인 정보를 이용하여 연구협력 네트워크의 구조, 특징, 진화를 탐구하는 것이다. 이를 위해 재료 기술분야(금속, 세라믹, 고분자 등 6개 기술분야) 및 혁신주체(산업계, 학계, 연구계)의 네트워크 구조 및 동태를 정량적으로 분석하며, 2010년∼2021년까지 한국의 공동특허 데이터를 활용하여 소셜 네트워크 분석(SNA)을 사용한다. 분석결과, 재료분야는 세부기술별로 네트워크의 차별점이 존재하며, 산업계, 학계, 연구계 등 혁신주체별 협력 강도의 명백한 단계별 특성을 가진다. 연구협력 네트워크의 규모는 점차 확장되어 ‘작은 세계’ 구조를 보여주고 있다. 본 연구를 통해 재료 정책 관점에서 지금까지 시행된 재료분야 산학연 협력 정책의 효과를 파악하는데 정책적 시사점을 제공함과 동시에, 보다 효과적인 재료 혁신주체 간의 네트워크를 구축하기 위한 근거 기반의 정책 수립에 도움이 될 수 있다.

The need for lightweight yet strong materials is being demanded in all industries. Carbon fiber-reinforced plastic is a material with increased strength by attaching carbon fiber to plastic, and is widely used in the aerospace industry, ships, automobiles, and civil engineering based on its low density. Carbon-reinforced fiber plastic is a material widely used in parts and manufactured products, and structural analysis simulation is required during design, and application of actual material properties is necessary for accurate structural analysis simulation. In the case of carbon-reinforced fiber plastics, it is reported that there is a porosity of around 0.5% to 6%, and it is necessary to check the change in material properties according to the porosity and pore shape. It was confirmed by applying the method. It was confirmed that the change in elastic modulus according to the porosity was 10.7% different from the base material when the porosity was 6.0%, and the Poisson's ratio was confirmed to be less than 3.0%. It was confirmed that the elliptical spherical pore derived different material properties from the spherical pore depending on the pore shape, and it was confirmed that the shape of the pore had to be confirmed to derive equivalent material properties.

This study was conducted on four types of laver soup prepared using recipes from Gangwon-do (GW), Gyeongsangnamdo (GN), Jeollanam-do (JN), and the media (MD). Salinities, soluble solids, free amino acids, color values, turbidities, and pH values of soups were measured, and sensory evaluations were done. pH values were significantly higher for GW and GN recipes than the JN and MD recipes (p<0.05). The salinities of JN and MD were significantly higher than those of the other soups (p<0.05). Regarding soluble solids, JN had the highest at 2.64oBrix, whereas GW had the lowest at 0.86 °Brix (p<0.05). GW and JN had higher concentrations of valine, phenylalanine, and glutamic acid (p<0.05). JN had significantly higher redness (a) than the other soups but significantly lower lightness (L) and yellowness (b) (p<0.05). Regarding transmittance, GW had a significantly higher value (67.67%T) than the other soups. JN and MD had higher acceptability results than GW or GN in terms of flavor, mouthfeel, and overall acceptability. Sensory intensity evaluations revealed that JN and MD had higher “soy sauce aroma” and “saltiness” and a greater “broth turbidity” than the other soups. These results indicate that the physicochemical and sensory characteristics of regional laver soups differ.

The study used the whole-life carbon assessment method to conduct a thorough carbon-neutral evaluation of a standard steel structure. To further assess carbon emissions, 11 design-changed models were evaluated, with changes made to the span between beams and columns. The results of the carbon emission assessment showed savings of approximately 13.1% by implementing the stage of the beyond life cycle. Additionally, the evaluation of carbon emissions through design changes revealed a difference of up to 42.2%. These findings confirmed that recycling and structural design changes can significantly reduce carbon emissions by up to 48.6%, making it an effective means of achieving carbon neutrality. It is therefore necessary to apply the stage of beyond life cycle and structural change to reduce carbon emissions.

본 논문에서는 3차원 엮임 재료의 재료 물성치들을 효율적으로 분석하고 추후 최적설계 연구에 활용하기 위해서 파라메트릭 배치 해석 워크플로우를 제시하였다. 3차원 엮임 재료를 구성하는 와이어들 사이의 간격을 설계 매개변수로 하는 파라메트릭 모델에 대해 서 임의의 변수 조합을 가지는 2,500개의 수치 모델을 생성하였으며, 상용 프로그램인 매트랩과 앤시스의 여러 모듈을 사용하여 체적 탄성계수, 열전도도, 유체투과율과 같은 다양한 재료 물성치들을 배치 해석을 통해서 자동으로 얻어질 수 있도록 구성하였다. 이와 같 이 얻어진 대용량의 재료 물성치 데이터베이스를 활용해서 회귀 분석을 수행하였으며, 그 결과 설계 변수들과 재료 물성치 사이의 경 향성과 수치 해석 결과의 정확도를 검증하였다. 또한 확보된 데이터베이스를 통해서 3차원 엮임 재료의 물성치를 예측할 수 있는 인 공 신경망을 구성하고 학습시켰으며, 그 결과 임의의 설계 매개변수 값들을 가지는 엮임 재료 모델에 대해서 구조 및 유체해석 과정 없 이도 높은 정확도로 재료 물성치들을 추정할 수 있음을 확인하였다.

일반적인 불투과형 사방댐은 제체 대부분이 콘크리트로 구성되어 분리 및 해체가 어려워 조속한 보강이 난해하다는 단점이 있다. 이러한 단점을 보완하기 위한 투과형 강재 스크린 사방댐이 제작되어 사용 중에 있지만, 강재가 부식되는 등 여러 문제를 보이는 실정이다. 이에 따라, 선행 연구에서는 강재 스크린 구조물을 내부식성이 뛰어난 GFRP로 대체하여 성능 및 안전 성을 검증하였지만, 동수압만 고려되는 등 다양한 조건이 고려되지 않은 것으로 확인되었다. 그렇기에 본 연구에서는 선행 연구 에서 수행된 GFRP 스크린 구조물뿐만 아니라, CFRP도 고려하였으며, 보다 다양한 표면 유속 별 하중 조건 및 유목, 토석류 등 과 같은 다양한 조건에서의 성능 비교 및 안전성 평가를 수행하였다. 해석 결과, GFRP와 CFRP는 강재 대비 제체에 작용하는 응력이 29.79∼91.73%가량 감소된 성능을 보이며, 이 외에도 충분한 안전성과 경제성을 겸비함을 확인하였다. 결론적으로 GFRP 및 CFPR 스크린 구조물은 강재 투과형 사방댐을 대체하여 사용하기에 충분하다고 판단되지만, 이는 수치 해석을 통한 결과이 므로 향후 실제 실험이 진행될 필요가 있을 것으로 판단된다.

본 연구에서는 PVA(Poly Vinyl Alcohol)섬유와 GO(Graphene Oxide)를 혼입한 섬유보강 콘크리트(FRC)의 역학적 특성 을 평가하고자 하였다. GO와 PVA 섬유를 동시에 혼입한 FRC 각각의 재료를 단일로 사용하였을 때보다 기대효과가 다소 미흡 하였지만, 각 재료의 하이브리드화로 인장강도가 개선되면서 PVA 섬유 혼입률 0.1∼0.3%과 GO 혼입률 0.025%에서 우수한 효 과를 얻을 수 있었다. 특히 PVA 섬유는 0.3%로 혼합하였을 때 부작용을 최소화하면서 최대의 효과를 보였지만, 적절한 GO 배 합비를 조절할 필요가 있으며 FRC내 GO와 PVA 섬유의 최적배합을 구하기 위한 추가적인 연구가 필요할 것으로 사료된다.

In order to respond to environmental pollution, developed countries, including Korea, have begun to conduct research to utilize hydrogen energy. For mass transfer of hydrogen energy, storage as liquid hydrogen is advantageous, and in this case, the volume can be reduced to 1/800. As such, the transportation technology of liquefied hydrogen for ships is expected to be needed in the near future, but there is no commercialized method yet. This study is a study on the technology to test the performance of the components constituting the membrane type storage container in a cryogenic environment as a preparation for the above. It is a study to find a way to respond by analyzing in advance the problems that may occur during the shear test of adhesives. Through this study, the limitations of ISO4587 were analyzed, and in order to cope with this, the specimen was supplemented so that fracture occurred in the adhesive, not the adhesive gripper, by using stainless steel, a low-temperature steel, to reinforce the thickness. Based on this, shear evaluation was performed under conditions lowered to minus 243℃, and it was confirmed that the breaking strength was higher at cryogenic temperatures.

This paper reports the results of an experimental examination using X-rays to test annealing materials for lapped bearing steel (STB2), to confirm the validity of the weighted averaging analysis method. The distribution behavior for the sin diagram and the presence or absence of differences in the peak method, half-value breadth method, and centroid method were investigated. When lapping the annealed bearing steel (STB2) material, a residual stress state with a non-directional steep gradient appeared in the surface layer, and it was found that the weighted averaging analysis method was effective. If there is a steep stress gradient, the sin diagram is curved and the diffraction intensity distribution curve becomes asymmetric, resulting in a difference between the peak method, half-value breadth method, and centroid method. This phenomenon was evident when the stress gradient was more than 2~3 kg/mm2/μm. In this case, if the position of the diffraction line is determined using the centroid method and the weighted averaging analysis method is applied, the stress value on the surface and the stress gradient under the surface can be obtained more accurately. When the stress gradient becomes a problem, since the curvature of the sin diagram appears clearly in the region of sin > 0.5, it is necessary to increase the inclination angle  as much as possible. In the case of a lapping layer, a more accurate value can be obtained by considering  in the weighted averaging analysis method. In an isotropic biaxial residual stress state, the presence or absence of  can be determined as the presence or absence of strain for sin≈0.4.

Metal material production process machinery is becoming larger due to the development of industry. Since there are many overseas manufacturers of large machines used in industrial fields, there are limitations in investigating the manufacturer's noise prediction method and measurement method. A noise map was prepared to obtain information necessary for noise reduction and to effectively manage noise companies. It was modeled with the drawings provided to prepare the noise map and the results of the actual measurement of the site. In order to improve the noise environment of workers, there was a noise reduction effect when a soundproof wall was installed between the noise source and the worker's workplace.

나노복합재료는 다기능성과 고성능을 가지는 혁신적인 복합재료이다. 나노 스케일 필러의 혼입함으로써 복합재료의 전기적, 역학 적 및 열적 특성이 크게 향상될 수 있기 때문에 나노 스케일 필러를 이용한 나노복합재료의 특성화에 관한 다양한 연구가 광범위하게 수행되어 왔다. 특히, 탄소계 나노 필러(탄소나노튜브, 카본블랙, 그래핀 나노판 등)를 활용하여 전기/역학적 특성을 향상시킨 나노복 합소재 개발에 관한 연구들이 복합재료 분야에서 큰 관심을 받고있다. 본 논문은 실제 응용에 필수적인 나노복합재료의 전기/역학적 특성을 문헌조사를 통해 고찰하는 것을 목표로 한다. 또한, 나노복합재료의 전기/역학적 특성 예측을 위한 최신 멀티스케일 모델링 연 구들에 대해서 검토하고, 멀티스케일 모델링에 대한 과제와 향후 발전 가능성에 대해서 논의한다.

The misuse of resources is getting serious every year, and the annual cost of domestic wates disposal announced by the Ministry of Environment is appraching 15 to 23 trillion won, Concerns are mounting that if the situation persists, the saturation of domestic waste landfill in 2025 will not be prevented. As the movement to prevent and solve global environmental problems increases, institutions, companies and individuals are increasingly interested in ‘Upcycle environmenal design’ that considers nature and composes spaces. This study explores solutions to environmental problems caused by waste, focusing on upcycle products and describes the uniform characteristics and effects of upcycle products shown through the analysis. The results of the study are as follows. First, upcycle products are not only treating waste but also protecting the environment at another level. Second, manufacturing upcycle products that take advantage of the original characteristics of packaging material. And third, drawing economic profits from upcycle products as well as the environment. The development of upcycle products according to social consciousness is creating a new environmental design for the surrounding environment(architecture, landscaping, interior, etc) and the movement to think and protect the environment leads to many changes in individual lives beyond institutions and companies. As the movement for environmental protection is expected to become more activement the outlook for upcycle products is also expected to rise further.

The most comprehensive and particularly reliable method for non-destructively measuring the residual stress of the surface layer of metals is the sin method. When X-rays were used the relationship of sin measured on the surface layer of the processing metal did not show linearity when the sin method was used. In this case, since the effective penetration depth changes according to the changing direction of the incident X-ray,  becomes a sin function. Since  cannot be used as a constant, the relationship in sin cannot be linear. Therefore, in this paper, the orthogonal function method according to Warren’s diffraction theory and the basic profile of normal distribution were synthesized, and the X-ray diffraction profile was calculated and reviewed when there was a linear strain (stress) gradient on the surface. When there is a strain gradient, the X-ray diffraction profile becomes asymmetric, and as a result, the peak position, the position of half-maximum, and the centroid position show different values. The difference between the peak position and the centroid position appeared more clearly as the strain (stress) gradient became larger, and the basic profile width was smaller. The weighted average strain enables stress analysis when there is a strain (stress) gradient, based on the strain value corresponding to the centroid position of the diffracted X-rays. At the 1/5 max height of X-ray diffraction, the position where the diffracted X-ray is divided into two by drawing a straight line parallel to the background, corresponds approximately to the centroid position.

Atomic layer etching (ALE) is a promising technique with atomic-level thickness controllability and high selectivity based on self-limiting surface reactions. ALE is performed by sequential exposure of the film surface to reactants, which results in surface modification and release of volatile species. Among the various ALE methods, thermal ALE involves a thermally activated reaction by employing gas species to release the modified surface without using energetic species, such as accelerated ions and neutral beams. In this study, the basic principle and surface reaction mechanisms of thermal ALE?processes, including “fluorination-ligand exchange reaction”, “conversion-etch reaction”, “conversion-fluorination reaction”, “oxidation-fluorination reaction”, “oxidation-ligand exchange reaction”, and “oxidation-conversion-fluorination reaction” are described. In addition, the reported thermal ALE processes for the removal of various oxides, metals, and nitrides are presented.