Flexible dye-sensitized solar cells using binder free TiO2 paste for low temperature sintering are developed. In this paste a small amount of titanium gel is added to a paste of TiO2 nanoparticle. Analysis of titanium gel paste prepared at 150 ℃ shows that it has a pure anatase phase in XRD and mesoporous structure in SEM. The formation of the titanium gel 1- 2 nm coated layer is confirmed by comparing the TEM image analysis of the titanium gel paste and the pristine paste. This coating layer improves the excited electron transfer and electrical contact between particles. The J-V curves of the organic binder DSSCs fabricated at 150℃ shows a current density of 0.12 mA/cm2 and an open-circuit voltage of 0.47 V, while the titanium gel DSSCs improves electrical characteristics to 5.04 mA/cm2 and 0.74 V. As a result, the photoelectric conversion efficiency of the organic binder DSSC prepared at low temperature is as low as 0.02 %, but the titanium gel paste DSSCs has a measured effciency of 2.76%.

Graphite was diffusion-bonded by hot-pressing to W-25Re alloy using a Ti interlayer. For the joining, a uniaxial pressure of 25 MPa was applied at 1600 oC for 2 hrs in an argon atmosphere with a heating rate of 10 oC min−1. The interfacial microstructure and elemental distribution of the W-25Re/Ti/Graphite joints were analyzed by scanning electron microscopy (SEM). Hot-pressed joints appeared to form a stable interlayer without any micro-cracking, pores, or defects. To investigate the high-temperature stability of the W-25Re/Ti/Graphite joint, an oxy-acetylene torch test was conducted for 30 seconds with oxygen and acetylene at a 1.3:1 ratio. Cross-sectional analysis of the joint was performed to compare the thickness of the oxide layer and its chemical composition. The thickness of W-25Re changed from 250 to 20 μm. In the elemental analysis, a high fraction of rhenium was detected at the surface oxidation layer of W-25Re, while the W-25Re matrix was found to maintain the initial weight ratio. Tungsten was first reacted with oxygen at a torch temperature over 2500 oC to form a tungsten oxide layer on the surface of W-25Re. Then, the remaining rhenium was subsequently reacted with oxygen to form rhenium oxide. The interfacial microstructure of the Ti-containing interlayer was stable after the torch test at a temperature over 2500 oC.

The organic binder-free paste for dye-sensitized solar cell (DSSC) has been investigated using peroxo titanium complex. The crystal structure of TiO2 nanoparticles, morphology of TiO2 film and electrical properties are analyzed by X-Ray Diffraction (XRD), Scanning Electron Microscopy (SEM), Electrochemical Impedance Spectra (EIS), and solar simulator. The synthesized TiO2 nanopowders by the peroxo titanium complex at 150, 300, 400˚C, and 450˚C have anatase phase and average crystal sizes are calculated to be 4.2, 13.7, 16.9, and 20.9 nm, respectively. The DSSC prepared by the peroxo titanium complex binder have higher Voc and lower Jsc values than that of the organic binder. It can be attributed to improvement of sintering properties of TCO/TiO2 and TiO2/TiO2 interface and to formation of agglomerate by the nanoparticles. As a result, we have investigated the organic binder-free paste and 3.178% conversion efficiency of the DSSC at 450˚C.

용액-확산 메커니즘에 의해 결정되는 기존의 고분자에서와는 달리, 촉진수송은 투과도와 선택도를 동시에 향상시킬 수 있는 기술이다. 본 연구에서는 은 나노입자, 폴리비닐피롤리돈, 7,7,8,8-테트라시야노퀴노디메탄으로 구성된 촉진수송 올레핀 분리막에 있어서, 메조기공 티타늄산화물(m-TiO2)에 대한 영향을 연구하였다. 특히 메조기공 티타늄산화물은 폴리비닐클로라이 드-g-폴리옥시에틸렌 메타크릴레이트 가지형 공중합체를 템플레이트로 하여 쉽고 대량 생산이 가능한 방법으로 제조하였다. 엑 스레이 회절분석에 따르면, 제조된 메조기공 티타늄산화물은 아나타제와 루타일 상의 혼합으로 구성되어 있으며, 결정의 크기가 약 16 nm 정도 되었다. 메조기공 티타늄산화물을 첨가하였을 때, 분리막의 확산도가 증가하여 혼합기체 투과도가 1.6에서 16 GPU로 증가하였고 선택도는 45에서 37로 약간 감소하였다. 메조기공 티타늄산화물이 첨가되지 않은 분리막은 장시간 성능이 유지되었으나, 메조기공 티타늄산화물이 첨가된 분리막의 경우 시간이 지남에 따라 투과도와 선택도가 감소하였다. 이는 티타늄 산화물과 은 사이의 화학적 상호작용으로 은 나노입자의 올레핀 운반체로써의 활성을 감소시키기 때문으로 사료된다.

Metastable phase characteristics of beta Ti alloys were investigated to consider the relationship of the microstructureand diffraction pattern in TEM. TEM analysis showed that the microstructure was mottled as a modulated structure, and thediffraction pattern was composed of spot streaks between the main spots of a stable beta phase with a specific latticerelationship. The modulated structure may be induced by short distance slip or atom movement during a very short intervalof solution treated and quenched (STQ) materials. The athermal ω phase, which could be precipitated at low temperature aging,is also analysed by the metastable phase. The metastable phases including athermal ω phase had a common characteristic ofhardened and brittle behavior because the dislocation slip was restricted by a super lattice effect due to short distance atommovement at the metastable state.

In this study, titanium(Ti) meshes and porous bodies are employed to synthesize carbon nanotubes(CNTs) using methane(CH4) gas and camphene solution, respectively, by chemical vapor deposition. Camphene is impregnated into Ti porous bodies prior to heating in a furnace. Various microscopic and spectroscopic techniques are utilized to analyze CNTs. It is found that CNTs are more densely and homogeneously populated on the camphene impregnated Ti-porous bodies as compared to CNTs synthesized with methane on Ti-porous bodies. It is elucidated that, when synthesized with methane, few CNTs are formed inside of Ti porous bodies due to methane supply limited by internal structures of Ti porous bodies. Ti-meshes and porous bodies are found to be multi-walled with high degree of structural disorders. These CNTs are expected to be utilized as catalyst supports in catalytic filters and purification systems.

Alumina dispersion strengthening copper(ADSC) alloy has great potential for use in many industrial applications such as contact supports, frictional break parts, electrode materials for lead wires, and spot welding with relatively high strength and good conductivity. In this study, we investigated the oxidation behavior of ADSC alloys. These alloys were fabricated in forms of plate and round type samples by surface oxidation reaction using Cu-0.8Al, Cu-0.4Al-0.4Ti, and Cu-0.6Al-0.4Ti(wt%) alloys. The alloys were oxidized at 980 oC for 1 h, 2 h, and 4 h in ambient atmosphere. The microstructure was observed with an optical microscope(OM) and a scanning electron microscope(SEM) equipped with energy-dispersive X-ray spectroscopy(EDS). Characterization of alumina was carried out using a 200 kV field-emission transmission electron microscope(TEM). As a result, various oxides including Ti were formed in the oxidation layer, in addition to γ-alumina. The thickness of the oxidation layer increased with Ti addition to the Cu-Al alloy and with the oxidation time. The corrected diffusion equation for the plate and round type samples showed different oxidation layer thickness under the same conditions. Diffusion length of the round type specimen had a value higher than that of its plate counterpart because the oxygen concentration per unit area of the round type specimen was higher than that of the plate type specimen at the same diffusiondepth.

In this study, flat-type photocatalytic reaction system is applied to reduce toxic hexavalent chromium (Cr(VI)) to trivalent chromium (Cr(III)) in aqueous solution under UV irradiation. To overcome the limitation of conventional photocatalysis, a novel approach toward photocatalytic system for reduction of hexavalent chromium including nanotubular TiO2 (NTT) on two kinds of titanium substrates (foil and mesh) were established. In addition, modified Ti substrates were prepared by bending treatment to increase reaction efficiency of Cr(VI) in the flat-type photocatalytic reactor. For the fabrication of NTT on Ti substrates, Ti foil and mesh was anodized with mixed electrolytes (NH4F-H2O-C2H6O2) and then annealed in ambient oxygen. The prepared NTT arrays were uniformly grown on two Ti substrates and surface property measurements were performed through SEM and XRD. Hydraulic retention time(HRT) and substrate type were significantly affected the Cr(VI) reduction. Hence, the photocatalytic Cr(VI) reduction was observed to be highest up to 95% at bended(modified) Ti mesh and lowest HRT. Especially, Ti mesh was more effective as NTT substrate in this research.

The effects of processing parameters on the flow behavior and microstructures were investigated in hotcompression of powder metallurgy (P/M) Ti-6Al-4V alloy. The alloy was fabricated by a blended elemental (B/E)approach and it exhibited lamellar α+β microstructure. The hot compression tests were performed in the range of tem-perature 800-1000℃ with 50℃ intervals, strain rate 10−4-10 s−1, and strain up to 0.5. At 800-950℃, continuous flowsoftening after a peak stress was observed with strain rates lower than 0.1 s−1. At strain rates higher than 1 s−1, rapiddrop in flow stress with strain hardening or broad oscillations was recorded. The processing map of P/M Ti-6Al-4V wasdesigned based on the compression test and revealed the peak efficiency at 850℃ and 0.001 s−1. As the processing tem-perature increased, the volume fraction of β phase was increased. In addition, below 950℃, the globularization of phaseat the slower strain rate and kinking microstructures were found. Based on these data, the preferred working conditionof the alloy may be in the range of 850-950℃ and strain rate of 0.001-0.01 s−1.

This research presents a preparation method of dental components by metal injection molding process (MIM process) using titanium scrap. About 20 μm sized spherical titanium powders for MIM process were successfully prepared by a novel dehydrogenation and spheroidization method using in-situ radio frequency thermal plasma treatment. The effects of MIM process parameters on the mechanical and biological properties of dental components were investigated and the optimum condition was obtained. After sintering at 1250oC for 1 hour in vacuum, the hardness and the tensile strength of MIMed titanium components were 289 Hv and 584 MPa, respectively. Prepared titanium dental components were not cytotoxic and they showed a good cell proliferation property.

Cold spray deposition using Titanium powder was carried out to investigate the effects of powder morphology and powder preheating on the coating properties such as porosity and hardness. The in-flight particle velocity of Ti powder in cold spray process was directly measured using the PIV (particle image velocimetry) equipment. Two types of powders (spherical and irregular ones) were used to manufacture cold sprayed coating layer. The results showed that the irregular morphology particle appeared higher in-flight particle velocity than that of the spherical one under the same process condition. The coating layer using irregular morphology powder represented lower porosity level and higher hardness. Two different preheating conditions (no preheating and preheating at ) were used in the process of cold spraying. The porosity decreased and the hardness increased by conducting preheating at . It was found that the coating properties using different preheating conditions were dependent not on the particle velocity but on the deformation temperature of particle. The deposition mechanism of particles in cold spray process was also discussed based on the experimental results of in flight-particle velocity.

This study investigated the effects of annealing environment for the densification and purification properties of pure titanium coating layer manufactured by cold spraying. The annealing was conducted at /1 h and three kinds of environments of vacuum, Ar gas, and mixture gas were controlled. Cold sprayed Ti coating layer (as sprayed) represented 6.7% of porosity and 228 HV of hardness, showing elongated particle shapes (severe plastic deformation) perpendicular to injection direction. Regardless of gas environments, all thermally heat treated coating layers consisted of pure -Ti and minimal oxide. Vacuum environment during heat treatment represented superior densification properties (3.8% porosity, 156.7 HV) to those of Ar gas (5.3%, 144.5 HV) and mixture gas (5.5%, 153.1 HV). From the results of phase analysis (XRD, EPMA, SEM, EDS), it was found that the vacuum environment during heat treatment could be effective for reducing oxide contents (purification) in the Ti coating layer. The characteristic of microstructural evolution with heat treatment was found to be different at three different gas environments. The controlling method for improving densification and purification in the cold sprayed Ti coating material was also discussed.