Catalytic activity changes of perovskite catalysts were examined with their A-site substitution. For the preparation of catalysts, Mn was used for B-site component and La, Ce, Sr, Ba, Ca, Ag were used for A-site component of the perovskite catalysts(ABO3) The effect of calcination temperature on methane combustion and perovskite structure was also investigated. The surface area and adsorbed oxygen species were tested with BET apparatus and O2-TPD, respectively. Perovskite catalysts whose A-site was partially substituted needed higher calcination temperature than un-substituted one to form the perovskite structure. From O2-TPD experiment, it was found that methane combustion activity was directly related to the oxygen desorbing ability of the catalysts. The prepared catalyst(LM-7) was stable at 600℃ for 72 hours of reaction.

It prepared the TiO2 powder which has photo-catalytic activity in the visible-light by the wet process with titanium oxysulfate. The titanium dioxide(TiO2) by the wet process creates a new absorption band in the visible light region, and is expected to create photocatalytic activity in this region. Anatase TiO2 powder which has photocatalytic activity in the visible light region, is treated using microwave and radio-frequency(RF) plasma. But, the TiO2 powder for the visible light region, which also can be easily produced by wet process. The wet process TiO2 absorbed visible light between 400nm and 600nm, and showed a high activity in this region, as measured by the oxidation removal of aceton from the gas phase. The AH-380 sample appears the yellow color to be strong, the catalytic activity in the visible ray was excellent in comparison with the plasma-treated TiO2. The AH-380 TiO2 powder, which can be easily produced on a large scale, is expected to have higher efficiency in utilizing solar energy than the plasma-treated TiO2 powder.

Synthesis gas is commercially produced by a steam reforming process. However, the process is highly endothermic and energy-consuming. Thus, this study was conducted to produce synthesis gas by the partial oxidation of methane to decrease the energy cost. Supported Ni catalysts were prepared by the impregnation method. To examine the activity of the catalysts, a differential fixed bed reactor was used, and the reaction was carried out at 750~850℃ and 1 atm. The fresh and used catalysts were characterized by XRD, XPS, TGA and AAS. The highest catalytic activity was obtained with the 13wt% Ni/MgO catalyst, with which methane conversion was 81%, and H2 and CO selectivities were 94% and 93%, respectively. 13wt% Ni/MgO catalyst showed the best MgNiO2 solid solution state, which can explain the highest catalytic activity of the 13wt% Ni/MgO catalyst.

There appeared enhancements of the conversion of methane by adding a small amount of CO in the aromatization reaction of methane using the Mo-zeolite catalyst. In case of adding CO2, CO2 changed to CO first, and then the conversion reaction occurred. It was observed by using isotopes as reactants that CO is related to the aromatization reaction of methane.

광화학 반응의 초기 유발을 위한 광촉매로 TiO2가 가장 널리 알려져 있으며, 기존의 상품보다 광촉매 활성도가 높은 촉매를 얻기 위해 Sol-Gel법을 이용하였다. TiO2 광촉매 제조를 위하여 전구체로서 Tetra-eth해-ortho-titanate(TEOT)를 이용하여 xerogeol 분말을 얻었으며, 광화학 반응의 효율을 측정하기 위해 분해대상 물질을 Dichloroacetic acid(DCA)로 선정하였다. 순수 titania 졸을 얻기 위한 최적조건은 알콕사이드 1몰당 물 40몰, 산 0.05몰이었고 pH의 범위는 3.3-3.6이었으며 Hexylene Glycol(HG)의 첨가량은 1몰임을 알 수 있었다. BET-N2방법을 이용하여 표면적을 측정한 결과 물/알콕 사이드의 몰비가 40-80범위에서 비표면적이 급격히 증가되어 DCA 의 광분해율도 증가하였으며, 몰 40몰을 첨가 후 졸-겔법으로 제조한 분말을 400˚C에서 1시간 열처리한 anatase phase의 TiO2가 최고의 광분해 효율인 약 21%를 보였다. 이는 상업용으로 가장 효율이 높은 Dagussa P-25의 DCA 분해 효율보다 2배 정도 높은 것으로 나타났다.

Lipases catalyzed the transesterification reaction between esters and various primary and secondary alcohols in a 99% organic medium, porcine pancreatic, yeast, mold lipases can vigorously act as catalysts in a number of nearly anhydrous organic solvents. Various transesterification reactions catalyzed by porcine pancreatic lipase in hexane obey Michaelis-Menten kinetics. The dependence of the catalytic activity of the enzyme in organic media on the pH of the aqueous solution from which it was recovered is bell-shaped, with the maximum coinciding with the pH optimum of the enzymatic activity in water. The catalytic power exhibited by the lipases in organic solvents is comparable to that displayed in water. In addition to transesterification, lipases Can catalyze several other processes in organic media.

Transesterification reactions (methyl methacrylate with monoethanolamine, methyl methacrylate with n-butyl alcohol, dimethylphthalate with ethylene glycol, dimethyl phthalate with monoethanolamine) were kinetically investigated in the presense of various metal acetate catalysts at 110℃. The amount of reactants was measured by gas and liquid chromatography, and the reaction rates also measured from the amount of reaction products and reactants upon each catalyst. The transesterification reactions were carried out under the first order conditions respect to the concentration of reactants, respectively. The overall reaction order was 2nd, Maximum reaction rates were appeared at the range of 1.4 to 1.6 in electronegativity of metal ions and maximum catalytic activities were obserbed at the range of 1.5 to 1,8 in instability constant of metal acetates.

Background : For the green approach of nanoparticles synthesizing, plant based technology has been considered as cost-effective and eco-friendly mass production. The oriental medicinal crop, Kalopanax septemlobus (Thunb.) Koidz. (Korean name: 음나무), the deciduous tree and a family of Araliaceae. Endemic tree of Asian countries, K. septemlobus being used for the treatment of various diseases. Phytochemicals of K. septemlobus such as polyphenols has highly probability of reducing agent for biosynthesizing nanoparticles. Methods and Results : In this study, we applied K. septemlobus ZnO nanoparticles (Ks-ZnO NPs) with procedures including green approach one-pot synthesis. For the characterization of nanoparticles, UV–Vis, FTIR, XRD, SEM and TEM were used. The formation of ZnO nanoparticles, the aurface plasmon resonance were observed at 372 ㎚ in UV-Vis spectroscopy. The presence of functional groups which as a capping agent and formation of ZnO nanoparticles were confirmed in FTIR result. The crystallization and morphology showed by XRD, TEM and SEM respectively. The photocatalytic activity of ZnO nanoparticles, was determined using Methylene blue (MB) dye degradation under UV irradiation (365 ㎚) which resulted rate constant is (−k) 0.1215 with 97.5% of degradation in 30 min. Conclusion : The result shows that phytochemicals in K. septemlobus extract have a potential as a reducing agent to form ZnO nanoparticles. The ZnO NPs are capable to degrade MB with in brief time.

Background : Panos extract is a mixture of four Panax plant extracts namely Dendropanax morbifera, Panax ginseng, Acanthopanax senticosus and Kalopanax septemlobus. We intended to use Panos extract for ZnO nanoparticles(NPs) synthesis and application for waste water treatment. Methods and Results : In the present study, we have synthesized Panos ZnO nanoparticles via co precipitation method. Characterization of the NPs has been done using X-ray diffraction (XRD), Fourier transformed infrared spectroscopy (FTIR) and UV-Visible spectroscopy. An average of 75% efficacy in degrading the methylene blue dye has been observed. The nanoparticles showed antibacterial activity against E. coli and S. aureus. Conclusion : The results shows that Panos ZnO NPs can be a potential eco-friendly and economical tool for waste water management in the current scenario where there an intense urge to remediate the polluted environment through novel approaches such as Nanobiotechnology.

Background : Codonopsis lanceolata is a perennial herb called as ‘Deodeok’ (더덕) in Korea. The roots of C. lanceolate has been reported to have some antioxidant and antimicrobial properties. The chemically reactive saponins of C. lanceolata might be used as a capping agent for the surface of ZnO nanoparticle, ultimately making it a highly efficient photocatalyst. Methods and Results : In this paper, we report the one-pot green synthesis of ZnO nanoparticles via precipitation method using root extract of C. lanceolata. The structure of green synthesized Cl-ZnO NPs was characterized using XRD, EDX, DLS and morphology using TEM. The FT-IR exhibited the information about the functional groups that capped the metal nanoparticle and the formation of metal NPs was confirmed by UV–vis spectra at 356nm. The Cl-ZnO NPs were evaluated for their catalytic activity by measuring the degradation of methylene blue (MB) dye in aqueous solution under UV light (365 ㎚). The result showed efficient degradation of MB, which was degraded 70% within 30 min by Cl-ZnO NPs. Conclusion : This study proves that the green route synthesized ZnO NPs from the root extract of C. lanceolata are low cost, time efficient, bio-degradable and non- toxic. The UVvis spectra confirmed the synthesis of ZnO NPs from C. lanceolata root extract. The Cl- ZnO NPs mediated catalysis exhibited high photocatalysis rate in short time. Ultimately, the green rapid synthesized Cl-ZnO NPs from root extract can be used as an efficient

Titania-supported chromium oxides with different loadings have been embarked in catalytic oxidation of trichloroethylene (TCE) to inquire association of the formation of crystalline Cr2O3 with catalytic performances. A better activity in the oxidative TCE decomposition at chosen temperatures was represented when chromium oxides (CrOx) had been dispersed on pure anatase-type TiO2 (DT51D) rather than on phase-mixed and sulfur-contained ones such as P25 and DT51. The extent of TCE oxidation at temperatures below 350℃ was a strong function of CrOx content in CrOx/DT51D TiO2, and a noticeable point was that the catalyst has two optimal CrOx loadings in which the lowest T50 and T90 values were measured for the TCE oxidation. This behavior in the activity with respect to CrOx amounts could be associated with the formation of crystalline Cr2O3 on the support surface, that is less active for the oxidation reaction, and an easier mobility of the surface oxygen existing in noncrystalline CrOx species with higher oxidation states, such as Cr2O8 and CrO3.

TiO2- and SiO2-supported Co3O4, Pt and Co3O4-Pt catalysts have been studied for CO and C3H8 oxidations at temperatures less than 250℃ which is a lower limit of light-off temperatures to oxidize them during emission test cycles of gasoline-fueled automotives with TWCs (three-way catalytic converters) consisting mainly of Pt, Pd and Rh. All the catalysts after appropriate activation such as calcination at 350℃ and reduction at 400℃ exhibited significant dependence on both their preparation techniques and supports upon CO oxidation at chosen temperatures. A Pt/TiO2 catalyst prepared by using an ion-exchange method (IE) has much better activity for such CO oxidation because of smaller Pt nanoparticles, compared to a supported Pt obtained via an incipient wetness (IW). Supported Co3O4-only catalysts are very active for CO oxidation even at 100℃, but the use of TiO2 as a support and the IW technique give the best performances. These effects on supports and preparation methods were indicated for Co3O4-Pt catalysts. Based on activity profiles of CO oxidation at 100℃ over a physical mixture of supported Pt and Co3O4 after activation under different conditions, and typical light-off temperatures of CO and unburned hydrocarbons in common TWCs as tested for C3H8 oxidation at 250℃ with a Pt-exchanged SiO2 catalyst, this study may offer an useful approach to substitute Co3O4 for a part of platinum group metals, particularly Pt, thereby lowering the usage of the precious metals.

The formation of ConTiOn+₂ compounds, i.e., CoTiO₃ and Co2TiO₄, in a 5 wt% CoOx/TiO2 catalyst after calcination at different temperatures has been characterized via scanning electron microscopy (SEM), Raman and X-ray photoelectron spectroscopy (XPS) measurements to verify our earlier model associated with Co3O4 nanoparticles present in the catalyst, and laboratory-synthesized ConTiOn+₂ chemicals have been employed to directly measure their activity profiles for CO oxidation at 100˚C. SEM measurements with the synthetic CoTiO₃ and Co2TiO₄ gave the respective tetragonal and rhombohedral morphology structures, in good agreement with the earlier XRD results. Weak Raman peaks at 239, 267 and 336 cm-1 appeared on 5 wt% CoOx/TiO₂ after calcination at 570oC but not on the catalyst calcined at 450˚C, and these peaks were observed for the ConTiOn+₂ compounds, particularly CoTiO3. All samples of the two cobalt titanate possessed O 1s XPS spectra comprised of strong peaks at 530.0±0.1 eV with a shoulder at a 532.2-eV binding energy. The O 1s structure at binding energies near 530.0 eV was shown for a sample of 5 wt% CoOx/TiO₂, irrespective to calcination temperature. The noticeable difference between the catalyst calcined at 450 and 570˚C is the 532.2 eV shoulder which was indicative of the formation of the ConTiOn+₂ compounds in the catalyst. No long-life activity maintenance of the synthetic ConTiOn+₂ compounds for CO oxidation at 100˚C was a good vehicle to strongly support the reason why the supported CoOx catalyst after calcination at 570˚C had been practically inactive for the oxidation reaction in our previous study; consequently, the earlier proposed model for the Co₃O₄ nanoparticles existing with the catalyst following calcination at different temperatures is very consistent with the characterization results and activity measurements with the cobalt titanates.

This study was investigated experimental condition which is able to evaluate photocatalytic activity of various commercial TiO₂. The experiments were performed for three representative substances (ethanol, phenol and methylene blue) and four kinds of commercial TiO₂, under the experimental conditions such as pH, reactant concentration, amount of TiO₂, reaction time and UV intensity. The optimum experimental conditions to evaluate photocatalytic activity were as follows : for ethanol, the initial concentration 1000 ppm, initial pH 8, TiO₂ loadings 0.1 wt%, and reaction time 90 minutes: for phenol, the initial concentration 200 ppm, initial pH 8, TiO₂loadings 1 wt%, and reaction time 60 minutes: for methylene blue, the initial concentration 200 ppm, initial pH 4, TiO₂ loadings 0.5 wt%, and reaction time 30 minutes.

Cobalt titanates (CoTiOx), such as CoTiO3 and Co2TiO4, have been synthesized via a solid-state reaction and characterized using X-ray diffraction (XRD) and X-ray photoelectron spectroscopic (XPS) measurement techniques, prior to being used for continuous wet trichloroethylene (TCE) oxidation at 36℃, to support our earlier chemical structure model for Co species in 5 wt% CoOx/TiO2 (fresh) and (spent) catalysts. Each XRD pattern for the synthesized CoTiO3 and Co2TiO4 was very close to those obtained from the respective standard XRD data files. The two CoTiOx samples gave Co 2p XPS spectra consisting of very strong main peaks for Co 2p3/2 and 2p1/2 with corresponding satellite structures at higher binding energies. The Co 2p3/2 main structure appeared at 781.3 eV for the CoTiO3, and it was indicated at 781.1 eV with the Co2TiO4. Not only could these binding energy values be very similar to that exhibited for the 5 wt% CoOx/TiO2 (fresh), but the spin-orbit splitting (ΔE) had also no noticeable difference between the cobalt titanates and a sample of the fresh catalyst. Neither of all the CoTiOx samples were active for the wet TCE oxidation, as expected, but a sample of pure Co3O4 had a good activity for this reaction. The earlier proposed model for the surface CoOx species existing with the fresh and spent catalysts is very consistent with the XPS characterization and activity measurements for the cobalt titanates.

The nanosized TiO2 photocatalysts were prepared by the hydrolysis of TiCl4 and calcined at different temperatures. The resulting materials were characterized by TGA, DSC, XRD, and TEM testing techniques. XRD, TEM, and BET measurements indicated that the particle size of TiO2 was increased with rise of calcination temperature and surface area was decreased with rise of it. The prepared TiO2 photocatalysts were used for the photocatalytic degradation of congo red. The effects of calcination temperature, TiO2 loading, the initial concentration of congo red, and usage frequencies were investigated and the rate constants were determined by regressing the experimental data. Calcination is an effective treatment to increase the photoactivity of nanosized TiO2 photocatalysts resulting from the improvement of crystallinity. The optimum calcination temperature of the catalyst for the efficient degradation of congo red was found to be 400℃. The rate constant was decreased with increase in the initial concentration of congo red and increased with increase in the TiO2 loading. In the case of TiO2 photocatalysts, the photocatalytic activity wasn't greatly affected by the usage frequencies.

Catalytic wet oxidation of trichloroethylene (TCE) in water has been conducted using TiO2-supported cobalt oxides at 36oC with a weight hourly space velocity of 7,500 h-1. 5% CoOx/TiO2, prepared by using an incipient wetness technique, might be the most promising catalyst for the wet oxidation although it exhibited a transient behavior in time on-stream activity. Not only could the bare support be inactive for the wet decomposition reaction, but no TCE removal also occurred by the process of adsorption on TiO2 surface. The catalytic activity was independent of all particle sizes used, thereby representing no mass transfer limitation in intraparticle diffusion. XPS spectra of both fresh and used Co surfaces gave different surface spectral features for each CoOx. Co 2p3/2 binding energy for Co species in the fresh catalyst appeared at 781.3 eV, which is very similar to the chemical states of CoTiOx such as Co2TiO4 and CoTiO3. The used catalyst exhibited a 780.3-eV main peak with a satellite structure at 795.8 eV. Based on XPS spectra of reference Co compound, the TCE-exposed Co surfaces could be assigned to be in the form of mainly Co3O4. XRD patterns for 5% CoOx/TiO2 catalyst indicated that the phase structure of Co species in the catalyst even before reaction is quite comparable to the diffraction lines of external Co3O4 standard. A model structure of CoOx present predominantly on titania surfaces would be Co3O4, encapsulated in thin-film CoTiOx species consisting of Co2TiO4 and CoTiO3, which may be active for the decomposition of TCE in a flow of water.