The purpose of this study is to provide basic data for the production of jackets with high fit by comparing and analyzing the adhesive and non-adhesive production methods of men's jackets. An analysis of the manufacturing method showcased differences between the adhesive and non-adhesive manufacturing methods in the cutting and wick attachment method, the shape and attachment method of the chest reinforcing wick, the sleeve attachment method, and the shoulder pad and sleeve reinforcing cloth attachment method. In evaluating the outfit, the overall fit of the shoulder, the fit of the chest, and the fit of the armpit were found to be high in the non-adhesive production method. In evaluating appearance evaluation, the front shoulder, chest, and sleeve overall appearance showed a high non-adhesive production method. Therefore, in order to increase the wearability of the shoulder pad and the the attachment method of the upper sleeve reinforcing cloth, the non-adhesive production method should be used, and in order to increase the overall wearability and armpit wear of the chest, the difference in the attachment method, and the reinforcement method of the armhole should be used. In addition, to increase the appearance of the jacket, non-adhesive production methods such as differences in wick attachment methods, shoulder pads, sleeve reinforcing cloth, and sleeve attachment methods should be used.

In order to respond to environmental pollution, developed countries, including Korea, have begun to conduct research to utilize hydrogen energy. For mass transfer of hydrogen energy, storage as liquid hydrogen is advantageous, and in this case, the volume can be reduced to 1/800. As such, the transportation technology of liquefied hydrogen for ships is expected to be needed in the near future, but there is no commercialized method yet. This study is a study on the technology to test the performance of the components constituting the membrane type storage container in a cryogenic environment as a preparation for the above. It is a study to find a way to respond by analyzing in advance the problems that may occur during the shear test of adhesives. Through this study, the limitations of ISO4587 were analyzed, and in order to cope with this, the specimen was supplemented so that fracture occurred in the adhesive, not the adhesive gripper, by using stainless steel, a low-temperature steel, to reinforce the thickness. Based on this, shear evaluation was performed under conditions lowered to minus 243℃, and it was confirmed that the breaking strength was higher at cryogenic temperatures.

본 연구는 딥러닝을 위한 비선형 변환 접근법을 사용하여 Single-lap joint의 접착 영역을 조사하기 위한 진동 응답 기반 탐지 시스템 을 제시한다. 산업 혹은 공학 분야에서 분해가 쉽지 않은 구조 내에 보이지 않는 부분의 상태와 접착된 구조의 접착 부위 상태를 알기 어려운 문제가 있다. 이러한 문제를 해결하기 위해 본 연구는 비선형 변환을 이용하여 기준 시편의 진동 응답으로 다양한 시편의 접착 면적을 조사하는 탐지 방법을 제안한다. 이 연구에서는 CNN 기반 딥러닝으로 진동 특성을 파악하기 위해 비선형 변환을 적용한 주파 수 응답 함수를 사용했고 분류를 위해 가상의 스펙트로그램을 사용했다. 또한, 제시된 방법을 검증하기 위해 알루미늄, 탄소섬유복합 재 그리고 초고분자량 폴리에틸렌 시편에 대한 진동 실험, 분석적 해, 유한요소해석을 수행했다.

Background: The traditional treatment protocol in adhesive capsulitis cases is physical therapy agents and a home exercise program. The extensive majority of patients respond to conservative treatment, but the painful rehabilitation program makes it inconvenient for individuals to fully comply with the treatment. In order to reduce pain and spasm, intraarticular injections or suprascapular nerve block may be effective before the rehabilitation program. Objectives: To investigated the effect of suprascapular nerve block (SNB), which is added to standard physical therapy on pain, functionality and range of motion in patients with adhesive capsulitis (AC). Design: Retrospective study. Methods: This study included 46 patients who were treated for AC. Patients in both groups were given 15 season physical therapy and home exercise. The treatment group consisted of patients who underwent multiple SNB in addition to physical therapy and home exercise. Datas were analyzed retrospectively. Results: The Visual Analogue Scale (VAS), ROM, Shoulder Pain and Disability Index (SPADI) and Constant scores in both groups after treatment and at the third month follow-up (P<.001). In the comparison between the groups, it was determined that the improvement in VAS, ROM and SPADI scores in the treatment group at the 3-month control was statistically significant (P<.05). Conclusion: Multiple SNB added to physical therapy and home exercise program in cases of AC may be effective in terms of pain control, increasing joint range of motion and improving functionality.

Conversion to modern hydrogen energy is required, and research on liquefied hydrogen cargo containment systems is needed for large-capacity transport and storage. In this study, changes in the mechanical properties of the adhesive required for storage and transport in liquid hydrogen were confirmed. The lap shear test was performed by realizing cryogenic conditions in a small chamber using liquid nitrogen and liquid helium. There was an increase of 11.0% in the -180℃ condition compared to room temperature, and an increase of 1.8% in the -230℃ condition compared to the -180℃ condition was confirmed. In the case of shear strain, it is known that it decreases as the temperature goes down. As a result of the experiment, it was confirmed that the value at room temperature and the value at -180℃ reduced the shear strain by 5.0%, and -230˚ compared to the -180℃ condition. An increase of 1.5% was confirmed in the C condition. In the case of the specimen tested at -230℃, the deformation in the gripper part was larger than in other tests, and it is judged that the maximum shear strength and shear strain were affected. In addition, in this study, there is a limitation in the experiment at -230°C rather than 253°C, which is the boiling point of hydrogen

In modern times, where problems due to environmental pollution are continuously occurring, hydrogen is in the spotlight as the energy of the future. Hydrogen is an eco-friendly energy resource that does not even generate CO2, and is actively supporting research to utilize hydrogen energy at the national level. This study is a study on the cryogenic mechanical properties of the elements constituting the cargo hold during the transportation of liquid hydrogen. Among the various components, the evaluation of mechanical properties of the cryogenic adhesive under liquid helium conditions was confirmed. The related contents are summarized as follows. As a result of performing SSRT by curing the adhesive, it was confirmed that tensile strength and maximum strain were increased at cryogenic temperature (-230°C) compared to room temperature (25°C). It was confirmed that the adhesive-hardened specimen showed a brittle fracture mode at both room temperature and cryogenic temperature during tensile. Improvements in this study, such as pores occurring during adhesive curing, the use of standard specimens, and experiments at -253°C, the boiling point of hydrogen, exist, and are planned to be carried out in subsequent studies.

This study develops a new device system for measuring a slope of object with non-adhesive, non-contact and non-face-to-face, namely Inclinometer Slope Laser Measuring (ISLM), that is applicable in the field. This system includes cradle, laser, camera, and computer and the filming and is performed after laser projection at programmed intervals. After measuring the amount of displacement converted to numerical values, these values can then be transferred to the office using the selected data transmission method. The obtained results from the test carried out to verify the reliability of the ISLM system indicated that the ISLM system can measure with accurately level of 0.1mm/Pixel at 1m distance and when increasing the camera resolution, the precision might increase proportionally. Therefore, the proposed measure system may widely apply on-site for various constructions, especially, in the case of object with very high surface temperature where exhibits difficulty to directly measure the adjacent structures. However, due to the sensitive reaction to the illuminance, this method can be applied with caution at times of large changes in illuminance, such as at dawn and at dusk.

본 논문에서는 정전기 흡착패드를 구성하는 곡면형 전극의 기하학적 엄밀성을 고려하기 위해 정전기 문제에 대하여 CAD에서 사 용하는 NURBS 기저함수를 직접 사용하는 아이소-지오메트릭 해석 기법을 도입하였다. 정전기 흡착력을 곡선 접촉면에서 구하는데 법선 벡터의 영향이 크므로 엄밀한 기하형상을 고려하는 아이소-지오메트릭 해석이 강점을 갖는다. 수치 예제를 통해 곡면과 평면에서 반복 구조의 유무에 따른 파라메터 연구를 수행하여 곡면형 전극의 흡착력이 좋은 성능을 가짐을 보였다. 정전기 흡착력의 성분을 분석하였을 때 정전기 흡착력의 차이는 법선 성분 전기장의 증가로 인한 것으로 파악되었다. 결론적으로 곡면형 전극에서도 전극 사이 거리가 가까워지는 아래로 볼록인 경우가 가장 성능이 좋고, 위로 볼록인 경우에는 성능이 가장 낮음을 보였다.

Background: Backpacks are one of the most widely used accessories in modern society. However, previous studies have shown that carrying a backpack can cause various musculoskeletal problems. Objectives: To investigate the effects of a body-adhesive backpack on craniovertebral angle, sagittal shoulder angle and the muscle fatigue in the upper extremity. Design: Randomized cross-over design. Methods: For this study, 36 healthy university students participated in this study. The experiment was conducted three times using common backpack, and body-adhesive backpack condition. The angles of the cervical spine and shoulder joints of the subjects were calculated without the backpack. Electrodes were placed at upper trapezius, lower trapezius, rectus abdominis and erector spinae to check for muscle fatigue. Subjects carried a backpack and walked on a treadmill for 15 minutes at 4 km/h. The muscle fatigue signal was also measured while walking. After walking, the craniovertebral and sagittal shoulder angles were measured again while subjects carried backpack. Results: As a result of this study, body-adhesive backpack condition showed significant decrease and significant increase in craniovertebral angle and sagittal shoulder angle than common backpack (P<.05). Body-adhesive backpack condition showed significant decrease in upper trapezius, lower trapezius, erector spinae, and rectus abdominis when compared to a common backpack (P<.05). Conclusion: This study suggests that a body-adhesive backpack is more beneficial in correcting body posture than a common backpack.

In this study, we fabricate a thin- and dense-BCuP-5 coating layer, one of the switching device multilayers, through a plasma spray process. In addition, the microstructure and macroscopic properties of the coating layer, such as hardness and bond strength, are investigated. Both the initial powder feedstock and plasma-sprayed BCuP-5 coating layer show the main Cu phase, Cu-Ag-Cu3P ternary phases, and Ag phase. This means that microstructural degradation does not occur during plasma spraying. The Vickers hardness of the coating layer was measured as 117.0 HV, indicating that the fine distribution of the three phases enables the excellent mechanical properties of the plasma-sprayed BCuP-5 coating layer. The pull-off strength of the plasma-sprayed BCuP-5 coating layer is measured as 16.5 kg/cm2. Based on the above findings, the applicability of plasma spray for the fabrication process of low-cost multi-layered electronic contact materials is discussed and suggested.

This paper aims at investigating the adhesive property at damage analysis according to the shape of the DCB test specimen made of Titanium, Dualumin as the high strength nonferrous metals. In this analysis, all three specimens had the lower holes bound by the cylinder support and the top holes were elongated with the rate of 6mm/min. The study results show that the longer the load block of DCB specimens, the more reliable and durable they are. It is utilized as the basic data at investigating the damage properties of adhesives in DCB specimens made of high strength nonferrous metals.

Background: Stretch-oriented home exercise programs are often used as treatments for patients with adhesive capsulitis; however, there is lack of research on home exercise programs to strengthen rotator cuffs. Objects: The aim of this study is to investigate the effect of home exercise programs for rotator cuff strengthening on pain, range of motion (ROM), disability level, and quality of life in patients with adhesive capsulitis. Methods: Twenty-two patients with adhesive capsulitis volunteered to participate in this study. The subjects were randomly divided into an experimental group (n = 11) and control group (n = 11). For the experimental group, manual therapy and home exercise programs for rotator cuff strengthening were applied for 6 weeks; for the control group, only manual therapy was applied for 6 weeks. Shoulder pain (quadruple visual analogue scale, QVAS), ROM, disability (shoulder pain and disability index-Korean version, SPADI), and quality of life (world health organization quality of life scale-Korean version, WHOQOL-BREF) were evaluated at baseline, after 3 weeks, and after 6 weeks of intervention. The changes in the measurement variables were analyzed by using repeated measure analysis of variance. Results: Significant differences were observed between the experimental group and control group in the QVAS; SPADI-pain scores; SPADI-disability scores; SPADI-total scores; flexion, abduction, internal and external rotation ROM of the glenohumeral joint; and WHOQOLBREF total, overall, physical health, and psychological scores. All groups displayed statistically significant improvements as observed in the QVAS, SPADI, flexion, abduction, external and internal rotation ROM of the glenohumeral joint, and WHOQOL-BREF. Conclusion: Home exercise programs for rotator cuff strengthening had a positive impact on shoulder pain, shoulder ROM, disability level, and quality of life in patients with adhesive capsulitis. Therefore, we propose the use of home exercise programs for rotator cuff strengthening in the exercise rehabilitation of patients with adhesive capsulitis.

PURPOSES: The objective of this study is to evaluate the shear and tensile strength properties of adhesive road studs in asphalt and concrete pavements. METHODS: The 300 mm×300 mm×50 mm rectangular specimens were fabricated using asphalt and concrete mixture for installation of road studs. Four 140-mm-radius circular areas were milled on each specimen with depth of 5 mm to install the adhesive road studs. About 100 g of thermal melting adhesive was applied on the milled area, and then the road stud was bonded onto the surface of the asphalt and concrete mixture. Direct shear testing was conducted at a speed of 5 mm/min on the interface between road stud and asphalt and concrete materials. Tensile strength testing was also conducted on the prepared specimens by applying load with increase of 50 kPa per second. These tests were performed not only in dry condition but also in wet condition to determine the effect of moisture on the shear and tensile strengths. RESULTS : According to the shear testing results, the average shear strength of asphalt samples in dry and wet conditions are 0.509 and 0.234 MPa, respectively. From this testing, the shear strength of wet sample was found to be decreased by 50% with respect to that of the dry sample. Similar trends can be observed on the concrete samples. The average tensile strength of asphalt samples was 0.187 MPa at 1.5 mm of displacement in dry condition. The concrete sample has a 0.222 MPa average tensile strength, which is slightly higher than that of the asphalt sample because of the rough surface characteristics of the concrete sample. CONCLUSIONS: It is determined from this study that the shear and tensile strengths of road stud bonded on the surface of asphalt mixture are slightly lower than those on concrete samples. Regardless of the pavement type, the wet conditioning of the sample can decrease the shear and tensile strength by 50% those of the dry sample. In the future, the quality improvement of adhesive and increase of specific surface area should be considered to improve the bonding property between road stud and pavement surface.