정삼투 여과막(FO) 기술 분야는 해수 담수화에서 이미 다양한 연구가 진행되었으나, 하폐수 처리 분야의 적용에서는 상대적으로 많은 연구가 필요한 상황이다. FO 기술은 비 다공성 특성막과 각 용액 사이의 삼투압 차이를 이용하여 원폐수로부터 수분을 비롯하여, 질소-인과 같은 이온성 물질까지 분리할 수 있다. 본 연구에서는 FO 막을 혐기성 유동상 미생물반응기(AFBR)를 통해 처리된 처리수 내 존재하는 질소(주로 암모니아성 질소)를 제거하기 위해 적용되었다. 유도용액(Draw Solution, DS)의 종류(NaCl, CaCl2, Na2CO3)에 따라 투과량은 NaCl, CaCl2, Na2CO3 순으로 높게 나타났으며, 암모니아성 질소의 배제율은 각각 42.25%, 78.83%, 70.35%으로 나타났다.

The lack of seed sludges for Ammonium Oxidizing Bacteria (AOB) and slow-growing ANaerobic AMMonium OXidation (ANAMMOX) bacteria is one of the major problem for large-scale application. In this study, 24m3 of single-stage SBR (Sequencing Batch Reactor) was operated to remove nitrogen from reject water using AOB and ANAMMOX bacteria cultivated from activated sludge in the field. The ANAMMOX activity was found after 44 days of cultivation in the ANAMMOX cultivation reactor, and then 0.66 kg N/m3/d of the nitrogen removal rate was achieved at 0.78 kg N/m3/d of the nitrogen loading rate at 153 days of cultivation. The AOB cultivation reactor showed 0.2 kg N/m3/d of nitrite production rate at 0.4 kg N/m3/d of nitrogen loading rate after 36 days of operation. The cultivated ANAMMOX bacteria and AOB was mixed into the single-stage SBR. The feed distribution was applied to remove total nitrogen stably in the single-stage SBR. The nitrogen removal rate in the single-stage SBR was gradually enhanced with an increase of specific activities of both AOB and ANAMMOX bacteria by showing 0.49 kg N/m3/d of the nitrogen removal rate at 0.56 kg N/m3/d of the nitrogen loading rate at 54 days of operation.

The objective of this study was to determine the effect of injection application of pig slurry on ammonia (NH3) and nitrous oxide (N2O) emission from timothy (Phleum pretense L.) sward. The three treatments were applied: 1) only water as a control, 2) pig slurry application by broadcasting, 3) pig slurry application by injection. The pig slurry was applied at a rate of 200 kg N ha-1. Total NH3 and N2O emission, expressed as a cumulative amount throughout the measurement time (40 days), was 2.68 kg NH3-N ha-1 and 6.58 g N2O-N ha-1, respectively, in the control. The injection application of pig slurry decreased total NH3 and N2O emission by 39.8% and 33.3%, respectively, compared to broadcasting application of pig slurry. The present study clearly showed that injection application exhibited positive roles in reducing N losses through NH3 and N2O emission.

Acidic and basic mixtures of odorous compounds are commonly emitted from various sources, and, in an absorption process, pH conditions in the liquid phase significantly affect the performance. In this study, the effect of pH on mass transfer in a bubble column reactor was evaluated using hydrogen sulfide and ammonia as a model mixture. Their mass transfer coefficients were then calculated. Furthermore, the total mass transfer coefficients as a function of pH were evaluated, and the experimental data were fitted into an empirical equation using dimensionless numbers. The mass transfer rates of hydrogen sulfide, the non-ionic form, increased dramatically with increasing pHs, while those of ammonia were almost unchanged because of its high solubility. As a result, a favorable pH condition for less soluble compounds must be selected to achieve high absorption capacity. The total mass transfer rates, which took into account pH effects as well as all the non-ionic and ionic constituents together, were found to be from 2.2 to 2.4 × 10−3 min−1 for hydrogen sulfide and ammonia, respectively, and they were almost constant at different pHs. The empirical equations, which were derived to obtain the best fit for the total mass transfer rates, implied that a method to increase diffusivity of each compound should be applied to improve overall mass transfer. In addition, when using the empirical equation, a mass transfer coefficient at a given set of pH and operating conditions can be calculated and used to design a water scrubbing process.

Epitaxial (1120) a-plane GaN films were grown on a (1102) R-plane sapphire substrate with photoresist (PR) masks using metal organic chemical vapor deposition (MOCVD). The PR mask with striped patterns was prepared using an ex-situ lithography process, whereas carbonization and heat treatment of the PR mask were carried out using an in-situ MOCVD. The heat treatment of the PR mask was continuously conducted in ambient H2/NH3 mixture gas at 1140℃ after carbonization by the pyrolysis in ambient H2 at 1100℃. As the time of the heat treatment progressed, the striped patterns of the carbonized PR mask shrank. The heat treatment of the carbonized PR mask facilitated epitaxial lateral overgrowth (ELO) of a-plane GaN films without carbon contamination on the R-plane sapphire substrate. Thhe surface morphology of a-plane GaN films was investigated by scanning electron microscopy and atomic force microscopy. The structural characteristics of a-plane GaN films on an R-plane sapphire substrate were evaluated by ω-2θ high-resolution X-ray diffraction. The a-plane GaN films were characterized by X-ray photoelectron spectroscopy (XPS) to determine carbon contamination from carbonized PR masks in the GaN film bulk. After Ar+ ion etching, XPS spectra indicated that carbon contamination exists only in the surface region. Finally, the heat treatment of carbonized PR masks was used to grow high-quality a-plane GaN films without carbon contamination. This approach showed the promising potential of the ELO process by using a PR mask.

본 연구에서는 질소산화물 제거용 환원제로 사용하는 요소 수용액을 암모니아로 전환하는데 있어 SCR 상용촉매의 활용가능성을 확인하기위해 촉매조성에 따른 반응온도, 공간속도의 영향에 대한 연구를 수행하였다. 연구결과 SCR 촉매로 널리 사용되는 V2O5/TiO2 촉매는 TiO2 및 WO3-V2O5/TiO2 촉매에 비해 암모니아 생성이 우수함을 보였다. 활성금속을 담지하지 않은 TiO2 촉매는 V2O5 혹은 WO3-V2O5를 담지 한 촉매에 비해 공간속도에 따른 암모니아 전환에 영향을 받지 않는 것으로 나타났으며, 활성금속을 담지 한 촉매는 공간속도가 증가함에 따라 암모니아 생성 농도가 감소됨을 확인하였다.

Tricholoma matsutake is a representative mushroom species with a characteristic pleasant aroma. The characteristic aroma component is methyl cinnamate, which is also produced in many plants. In basil, cinnamic acid is produced from l-phenylalanine (l-Phe) by phenylalanine ammonia-lyase (PAL) and converted to methyl cinnamate by a cinnamate/p-coumarate carboxyl methyltransferase. Two PAL genes, Tmpal1 and Tmpal2, have been isolated from T. matsutake. In this study, we aimed to clarify the relationships between l-Phe, methyl cinnamate production, and PAL expression in the mycelium of T. matsutake strain NBRC 30605. For this purpose, methyl cinnamate content, PAL activity, and transcript levels of Tmpal1 and Tmpal2 were examined in the mycelia of T. matsutake supplemented with l-Phe. The mycelia were cultured in 20 mL of a liquid medium (2% glucose, 0.15% yeast extract, and 0.15% Bacto Soytone) at 20 °C for 45 d, supplemented with 0.5-6 mM l-Phe, and then grown for a further 15 d. Mycelia cultured without l-Phe supplementation for 60 d in the medium were used as a control. Crude extracts were prepared from the mycelia harvested for enzymatic, protein, and methyl cinnamate assays. Methyl cinnamate was measured using gas chromatography. PAL activity was assayed by measuring the rate of trans-cinnamic acid formation as the absorbance at 290 nm (ɛ290 = 10,000 M−1 cm−1). The transcript levels of Tmpal1 and Tmpal2 were examined by performing real-time reverse transcriptase-quantitative PCR on the total RNA. Methyl cinnamate was detected in very low levels in cultures without l-Phe supplementation, but its content per mg of protein increased markedly with increasing concentrations of l-Phe, especially at 4-6 mM. When 6 mM l-Phe was added to the culture medium, the methyl cinnamate content was approximately 55-fold higher than that of the control sample. The specific activity of PAL also increased in cultures supplemented with l-Phe, especially at 4-6 mM. When l-Phe was added to the culture medium, the methyl cinnamate content in the mycelia was relatively well correlated with PAL activity. These results indicated that supplementation with l-Phe, a precursor of methyl cinnamate, increases the specific activity of PAL, leading to an increase in methyl cinnamate production in the mycelia of T. matsutake. The transcript level of Tmpal1 did not change markedly with l-Phe supplementation. In contrast, the transcript level of Tmpal2 increased greatly in cultures supplemented with 4-6 mM l-Phe. These results suggested that the expression of Tmpal1 and Tmpal2 was controlled by different regulatory mechanisms and that they may have different biological functions in T. matsutake. In addition, the pattern of PAL activity in the presence of l-Phe was similar to that of the transcript level of Tmpal2, but not Tmpal1, suggesting that the increase in PAL activity was dependent on the increased transcription of Tmpal2.

The present study was conducted to determine the optimal supplementation level of beta-mannanase in the diet of laying hens. A total of 320 Hy-Line Brown layers (80 weeks of age) were assigned randomly into four groups on the basis of laying performance. Each treatment had eight replicates with 10 birds each (80 birds per treatment). Two hens were caged individually. Treatments were basal diet supplemented with 0 (control), 0.04, 0.08, and 0.16% beta-mannanase during the nine-week feeding period. Laying hens fed diets supplemented with increasing levels of beta-mannanase had increased (linear, p<0.05) overall egg production and egg mass. In addition, these hens had greater retention of dry matter, crude protein, gross energy, calcium, and mannan (linear, p<0.05). Dietary beta-mannanase treatments had no effect on blood metabolites such as total carbohydrate, triglycerides, glucose, total protein, and blood urea nitrogen, or excreted ammonia nitrogen and volatile fatty acids. The results obtained in present study indicate that dietary supplementation of beta-mannanase has the potential for improving the performance of laying hens. The optimal supplementation level is 0.04% beta-mannanase in the diet.

The effects of ammonia-treated graphene oxide (GO) on composites based on epoxy resin were investigated. Ammonia solutions of different concentrations (14–28%) were used to modify GO. Nitrogen functional groups were introduced on the GO surfaces without significant structural changes. The ammonia-treated GO-based epoxy composites exhibited interesting changes in their mechanical properties related to the presence of nitrogen functional groups, particularly amine (C-NH2) groups on the GO surfaces. The highest tensile and impact strength values were 42.1 MPa and 12.3 J/m, respectively, which were observed in an epoxy composite prepared with GO treated with a 28% ammonia solution. This improved tensile strength was 2.2 and 1.3 times higher than those of the neat epoxy and the non-treated GO-based epoxy composite, respectively. The amine groups on the GO ensure its participation in the cross-linking reaction of the epoxy resin under amine curing agent condition and enhance its interfacial bonding with the epoxy resin.

This study investigated the effect of high concentration of free ammonia on microalgal growth and substrate removal by applying real wastewater nitrogen ratio. To test of this, the conditions of free ammonia 1, 3, 6, 9, 12, 15 mg-N/L are compared. After 3 days of incubation, algal growth of Chlorella vulgaris and carbon removal rate are respectively lower in the reactors of FA 12, 15 mg-N/L compared to the others. This indicates that the high concentration of free ammonia, in this case, above 12 mg-N/L, has negative effect on algal growth and metabolic activity. Also, high concentration of free ammonia causes the proton imbalance, ammonium accumulation in algae and has toxicity for these reasons. So, we have to consider free ammonia in applying the microalgae to wastewater treatment system by the way of diluting wastewater or controlling pH and temperature.

The objective of this study was to determine the effect of nitrification inhibitor dicyandiamide (DCD) and urease inhibitor hydroquinone (HQ) on ammonia (NH3) and nitrous oxide (N2O) emission from pig slurry applied to Timothy (Phleum pretense L.) sward. The daily emission of ammonia (NH3) and nitrous oxide (N2O) was monitored for 9 days in three different treatments; 1) control (only pig slurry application), 2) DCD treatment (pig slurry + DCD), and 3) HQ treatment (pig slurry + HQ). Most NH3 emission occurred after 4~5 days in three treatments. Total NH3 emission, expressed as a cumulative amount throughout the measurement time, was 1.33 kg N ha 1 in the control. The DCD and HQ treatment decreased total NH3 emission by 16.3% and 25.1%, respectively, compared to the control. Total N2O emission in the control was 47.1 g N ha 1. The DCD and HQ treatment resulted in a reduction of 67.9% and 41.8% in total N2O emission, respectively, compared to the control. The present study clearly indicated that nitrification and urease inhibitor exhibited positive roles in reducing N losses through NH3 and N2O emission.

기존 연구에서는 스크러버를 이용한 NO2 를 제거하기 위해 암모니아 수용액을 적용한다. 하 지만 암모니아는 독성 및 악취가 강해 실선 적용에 어려움이 따를 수 있어, 암모니아를 대체할 수 있는 물질을 찾기 위해 이 연구를 진행하였다. 대체 물질로는 수산화나트륨(NaOH), 티오황산나트륨 (Na2S2O3), 요소(Urea)를 사용하였다. 세정액을 제외한 모든 부분은 기존 암모니아를 적용한 실험의 최 적 조건과 동일하게 진행하였다. 그 결과 실험에 사용된 세 가지 물질 중 두 물질은 암모니아 용액과 대체가 가능한 것으로 사료되었으며, 최적조건은 각각 NaOH 2.5 %, Na2S2O3 5.0 % 에서 가장 높은 효 율을 나타냈다. Urea는 효율이 일정하게 지속되지 않아 대체 물질로는 적합하지 않음을 확인 할 수 있 었다.