In this study, we investigated the precipitation behavior of the R-phase precipitated at the initial stage of aging and its effects on the mechanical properties of 25%Cr-7%Ni-2%Mo-4%W super duplex stainless steel. The R-phase was mainly precipitated at the interface of ferrite/austenite phases and inside of the ferrite phase during the initial stage of aging. It was transformed into the σ-phase with an increase of the aging time. The ferrite phase was decomposed into a new austenite(γ2)phase and the σ-phase by an aging treatment. The R phase was an intermetallic compound showing higher molybdenum and tungsten concentrations than the matrix and also showed higher molybdenum and tungsten concentrations than the σ phase. In the initial stage of aging, precipitation of the R-phase did not change the hardness, the strength and the elongation. The hardness and the strength increased upon a longer aging time, but the elongation rapidly decreased. These results show that the R-phase did not significantly affect the hardness and the strength, though it did influence the elongation.

The connecting rod is one of the most important parts in automotive engines, transforming the reciprocalmotion of a piston generated by internal combustion into the rotational motion of a crankshaft. Recent advances in highperformance automobile engines demand corresponding technological breakthroughs in the materials for engine parts. Inthe present research, the powder metallurgy (P/M) process was used to replace conventional quenching and/or temperingprocesses for mass production and ultimately for more cost-efficient manufacturing of high strength connecting rods.The development of P/M alloy powder was undertaken not only to achieve the improvement in mechanical properties,but also to enhance the machinability of the P/M processed connecting rods. Specifically MoS2 powders were added aslubricants to non-normalizing Fe-Cr-Mn-V-C alloy powder to improve the post-sintering machinability. The effects ofMoS2 addition on the microstructure, mechanical properties, and machining characteristics were investigated.

15Cr-1Mo base oxide dispersion strengthened (ODS) steel which is considered to be as a promising candidate for high- temperature components in nuclear fusion and fission systems because of its excellent high temperature strength, corrosion and radiation resistance was fabricated by using mechanical alloying, hot isostatic pressing and hot rolling. Torsion tests were performed at room temperature, leading to two different shear strain routes in the forward and reverse directions. In this study, microstructure evolution of the ODS steel during simple shearing was investigated. Fine grained microstructure and a cell structure of dislocation with low angle boundaries were characterized with shear strain in the shear deformed region by electron backscattered diffraction (EBSD). Grain refinement with shear strain resulted in an increase in hardness. After the forward-reverse torsion, the hardness value was measured to be higher than that of the forward torsion only with an identical shear strain amount, suggesting that new dislocation cell structures inside the grain were generated, thus resulting in a larger strengthening of the steel.

Metallic Cr film coatings of 1.2μm thickness were prepared by DC magnetron sputter deposition method on c-plane sapphire substrates. The thin Cr films were ammoniated during horizontal furnace thermal annealing for 10-240 min in NH3 gas flow conditions between 400 and 900˚C. After annealing, changes in the crystal phase and chemical constituents of the films were characterized using X-ray diffraction (XRD) and energy dispersive X-ray photoelectron spectroscopy (XPS) surface analysis. Nitridation of the metallic Cr films begins at 500˚C and with further increases in annealing temperature not only chromium nitrides (Cr2N and CrN) but also chromium oxide (Cr2O3) was detected. The oxygen in the films originated from contamination during the film formation. With further increase of temperature above 800˚C, the nitrogen species were sufficiently supplied to the film's surface and transformed to the single-phase of CrN. However, the CrN phase was only available in a very small process window owing to the oxygen contamination during the sputter deposition. From the XPS analysis, the atomic concentration of oxygen in the as-deposited film was about 40 at% and decreased to the value of 15 at% with increase in annealing temperature up to 900˚C, while the nitrogen concentration was increased to 42 at%.

This study was carried out to investigate the effect on the growth and antioxidant activities of Cichorium intybus L.(CLE), Cichorium intybus L. var. folisum ‘treviso’ (CLET), Cichorium intybus L. var. folisum ‘rosaitaliana’ (CLER) in hydroponics added with Cr3+ or Selenium (Se) for 4 weeks. Total polyphenol, total flavonoids contents and FRAP values of three species of chicory were grown hydroponically with Cr3+ or Se were increased. These extracts were also showed stronger DPPH and ABTS scavenging activity than chicory extracts. In particular, chicories added with Cr3+ had higher antioxidant activities than chicories added with Se. CLER and CLE extracts added with Cr3+ were also showed α-glucosidase inhibition activities. These results indicate that chicories were cultivated in culture fluid added with Cr3+ or Se could be used as high functional vegetables.

Fe-Cr-Al powder porous metal was manufactured by using new electro-spray process. First, ultra-finefecralloy powders were produced by using the submerged electric wire explosion process. Evenly distributed colloid(0.05~0.5% powders) was dispersed on Polyurethane foam through the electro-spray process. And then degreasing andsintering processes were conduced. In order to examine the effect of cell size (200 µm, 450 µm, 500 µm) in process,pre-samples were sintered for two hours at temperature of 1450˚C, in H₂ atmospheres. A 24-hour thermo gravimetricanalysis test was conducted at 1000˚C in a 79% N₂ + 21% O₂ to investigate the high temperature oxidation behavior ofpowder porous metal. The results of the high temperature oxidation tests showed that oxidation resistance increased withincreasing cell size. In the 200 µm porous metal with a thinner strut and larger specific surface area, the depletion ofthe stabilizing elements such as Al and Cr occurred more quickly during the high-temperature oxidation compared withthe 450, 500 µm porous metals.

The effect of interstitial elements on the ductile-brittle transition behavior of austenitic Fe-18Cr-10Mn-2Ni alloys with different nitrogen and carbon contents was investigated in this study. All the alloys exhibited ductile-brittle transition behavior because of unusual low-temperature brittle fracture, even though they have a faced-centered cubic structure. With the same interstitial content, the combined addition of nitrogen and carbon, compared to the sole addition of nitrogen, improved the low-temperature toughness and thus decreased the ductile-brittle transition temperature (DBTT) because this combined addition effectively enhances the metallic component of the interatomic bonds and is accompanied by good plasticity and toughness due to the increased free electron concentration. The increase in carbon content or of the carbon-to-nitrogen ratio, however, could increase the DBTT since either of these causes the occurrence of intergranular fracture that lead to the deterioration of the toughness at low temperatures. The secondary ion mass spectroscopy analysis results for the observation of carbon and nitrogen distributions confirms that the carbon and nitrogen atoms were significantly segregated to the austenite grain boundaries and then caused grain boundary embrittlement. In order to successfully develop austenitic Fe-Cr-Mn alloys for low-temperature application, therefore, more systematic study is required to determine the optimum content and ratio of carbon and nitrogen in terms of free electron concentration and grain boundary embrittlement.

The hardenability of low-carbon boron steels with different molybdenum and chromium contents was investigated using dilatometry, microstructural observations and secondary ion mass spectroscopy (SIMS), and then discussed in terms of the segregation and precipitation behaviors of boron. The hardenability was quantitatively evaluated by a critical cooling rate obtained from the hardness distribution plotted as a function of cooling rate. It was found that the molybdenum addition was more effective than the chromium addition to increase the hardenability of boron steels, in contrast to boron-free steels. The addition of 0.2 wt.% molybdenum completely suppressed the formation of eutectoid ferrite, even at the slow cooling rate of 0.2˚C/s, while the addition of 0.5 wt.% chromium did this at cooling rates above 3˚C/s. The SIMS analysis results to observe the boron distribution at the austenite grain boundaries confirmed that the addition of 0.2 wt.% molybdenum effectively increased the hardenability of boron steels, as the boron atoms were significantly segregated to the austenite grain boundaries without the precipitation of borocarbide, thus retarding the austenite-to-ferrite transformation compared to the addition of 0.5 wt.% chromium. On the other hand, the synergistic effect of molybdenum and boron on the hardenability of boron steels could be explained from thermodynamic and kinetic perspectives.

본 연구에서는 ALBC3 합금에 Ni기 자용성 합금으로 내마모성 및 내캐비테이션 특성을 향상시키기 위하여 용사코팅 후 열처리를 실시하여 캐비테이션 특성을 평가하였다. 본 연구 결과, 자용성 합금 코팅층이 높은 경도를 나타내어 내마모성이 우수할 것으로 판단되나, 다공질의 조직으로 인해 열악한 내캐비테이션 특성을 나타냈다. 따라서 열처리 조건의 최적화가 중요하며, 본 조건에서는 열처리온도를 높여 자용성 합금 내 B와 Si의 유동성을 증가시킴으로써 기공이나 결함을 제거하여 특성개선 효과를 기대할 수 있을 것으로 판단된다.

Over the past few decades, high-nitrogen austenitic steels have steadily received greater attention since they provide a unique combination of high strength and ductility, good corrosion resistance, and non-magnetic properties. Recently, highnitrogen 18Mn-18Cr austenitic steels with enhanced strength have been developed and widely used for generator retaining rings in order to prevent the copper wiring from being displaced by the centrifugal forces occurring during high-speed rotation. The high-nitrogen austenitic steels for generator retaining ring should be expanded at room temperature and then stress relief annealed at around 400˚C to achieve the required mechanical properties. In this study, four kinds of high-nitrogen 18Mn-18Cr austenitic steels with different nitrogen content were fabricated by using a pressurized vacuum induction melting furnace, and then the effects of nitrogen content, cold working, and stress relieving on tensile properties were investigated. The yield and tensile strengths increased proportionally with increasing nitrogen content and cold working, and they further increased after stress relieving treatment. Based on these results, a semi-empirical equation was proposed to predict the tensile strength of highnitrogen 18Mn-18Cr austenitic steels for generator retaining rings. It will be a useful for the effective fabrication of high-nitrogen 18Mn-18Cr austenitic steels for generator retaining rings with the required tensile properties.

Materials design and processing development proposed in this study, aims at contributing to high wear resistant and friction characteristics. To find wear resistant and friction with inner elbow pipe, it is needed hardness and frictional condition test to be capable of supplying with high Cr casting steel. The result of HTV(heat treatment in vacuum) shows that hardness increased with increasing Cr content in % carbide phase. It was about 7∼10% of hardness improvement compared to original casting elbow pipe. This behavior of the hardness of Cr casting steel was explained by the types of chemical bonds that hold atoms together in Cr carbide phase. Through the friction coefficient and wear loss test, with the increasing of Cr wt% reduction in the coefficient of friction and wear loss.

The influence of Cu and Ni on the ductile-brittle transition behavior of metastable austenitic Fe-18Cr-10Mn-N alloys with N contents below 0.5 wt.% was investigated in terms of austenite stability and microstructure. All the metastable austenitic Fe-18Cr-10Mn-N alloys exhibited a ductile-brittle transition behavior by unusual low-temperature brittle fracture, irrespective of Cu and/or Ni addition, and deformation-induced martensitic transformation occasionally occurred during Charpy impact testing at lower temperatures due to reduced austenite stability resulting from insufficient N content. The formation of deformation-induced martensite substantially increased the ductile-brittle transition temperature(DBTT) by deteriorating low-temperature toughness because the martensite was more brittle than the parent austenite phase beyond the energy absorbed during transformation, and its volume fraction was too small. On the other hand, the Cu addition to the metastable austenitic Fe-18Cr-10Mn-N alloy increased DBTT because the presence of δ-ferrite had a negative effect on low-temperature toughness. However, the combined addition of Cu and Ni to the metastable austenitic Fe-18Cr-10Mn-N alloy decreased DBTT, compared to the sole addtion of Ni or Cu. This could be explained by the fact that the combined addition of Cu and Ni largely enhanced austenite stability, and suppressed the formation of deformation-induced martensite and δ-ferrite in conjunction with the beneficial effect of Cu which may increase stacking fault energy, so that it allows cross-slip to occur and thus reduces the planarity of the deformation mechanism.

Spatial distributions of alloying elements of an Fe-based amorphous ribbon with a nominal composition of Fe75C11Si2B8Cr4 were analyzed through the atom probe tomography method. The amorphous ribbon was prepared through the melt spinning method. The macroscopic amorphous natures were confirmed using an X-ray diffractometer (XRD) and a differential scanning calorimeter (DSC). Atom Probe (Cameca LEAP 3000X HR) analyses were carried out in pulsed voltage mode at a specimen base temperature of about 60 K, a pulse to base voltage ratio of 15 %, and a pulse frequency of 200 kHz. The target detection rate was set to 5 ions per 1000 pulses. Based on a statistical analyses of the data obtained from the volume of 59×59×33nm3, homogeneous distributions of alloying elements in nano-scales were concluded. Even with high carbon and strong carbide forming element contents, nano-scale segregation zones of alloying elements were not detected within the Fe-based amorphous ribbon. However, the existence of small sub-nanometer scale clusters due to short range ordering cannot be completely excluded.

The effect of particle size distribution on green and sintered properties of Fe-Cr-Mo prealloy powder was investigated in this study. For the study, prealloyed Fe-Cr-Mo powders with different particle sizes were mixed as various ratios and cold compacted at various pressure and sintered at for 30 min, atmosphere in the continuous sintering furnace. The results shows that the powders with large particle size distribution have high compressibility and low ejection force. However the green strength are much less than those with small particle size distribution. Tensile prperties of the sintered specimes with large particles size also have high strength and elongation.

We have examined the co-doping effects of 1/2mol% NiO and 1/4mol% Cr2O3 (Ni:Cr=1:1) on the reaction,microstructure, and electrical properties, such as the bulk defects and the grain boundary properties, of ZnO-Bi2O3-Sb2O3 (ZBS;Sb/Bi=0.5, 1.0, and 2.0) varistors. The sintering and electrical properties of Ni,Cr-doped ZBS, ZBS(NiCr) varistors werecontrolled using the Sb/Bi ratio. Pyrochlore (Zn2Bi3Sb3O14), α-spinel (Zn7Sb2O12), and δ-Bi2O3 were detected for all ofcompositions. For the sample with Sb/Bi=1.0, the Pyrochlore was decomposed and promoted densification at lowertemperature by Ni rather than by Cr. A homogeneous microstructure was obtained for all of the samples affected by α-spinel.The varistor characteristics were not dramatically improved (non-linear coefficient, α=5~24), and seemed to formZni..(0.17eV) and Vo.(0.33eV) as dominant defects. From impedance and modulus spectroscopy, the grain boundaries werefound to have been divided into two types, i.e., one is tentatively assigned to ZnO/Bi2O3 (Ni,Cr)/ZnO (0.98eV) and the otheris assigned to a ZnO/ZnO (~1.5eV) homojunction.

In this study we aimed to examine the co-doping effects of 1/6mol% Co3O4 and 1/4mol% Cr2O3 (Co:Cr=1:1)on the reaction, microstructure, and electrical properties, such as the bulk defects and the grain boundary properties, of ZnO-Bi2O3-Sb2O3 (ZBS; Sb/Bi=0.5, 1.0, and 2.0) varistors. The sintering and electrical properties of Co,Cr-doped ZBS, ZBS(CoCr)varistors were controlled using the Sb/Bi ratio. Pyrochlore (Zn2Bi3Sb3O14), α-spinel (Zn7Sb2O12), and δ-Bi2O3 were formed inall systems. Pyrochlore was decomposed and promoted densification at lower temperature on heating in Sb/Bi=1.0 by Cr ratherthan Co. A more homogeneous microstructure was obtained in all systems affected by α-spinel. In ZBS(CoCr), the varistorcharacteristics were improved (non-linear coefficient, α=20~63), and seemed to form Zni..(0.20eV) and Vo.(0.33eV) asdominant defects. From impedance and modulus spectroscopy, the grain boundaries were found to be composed of anelectrically single barrier (0.94~1.1eV) that is, however, somewhat sensitive to ambient oxygen with temperature. The phasedevelopment, densification, and microstructure were controlled by Cr rather than by Co but the electrical and grain boundaryproperties were controlled by Co rather than by Cr.

We aimed to examine the co-doping effects of 1/6mol% Mn3O4 and 1/4mol% Cr2O3 (Mn:Cr=1:1) on the reaction,microstructure, and electrical properties, such as the bulk defects and grain boundary properties, of ZnO-Bi2O3-Sb2O3 (ZBS;Sb/Bi=0.5, 1.0, and 2.0) varistors. The sintering and electrical properties of Mn,Cr-doped ZBS, ZBS(MnCr) varistors werecontrolled using the Sb/Bi ratio. Pyrochlore (Zn2Bi3Sb3O14), α-spinel (Zn7Sb2O12), and δ-Bi2O3 (also β-Bi2O3 at Sb/Bi≤1.0)were detected for all of the systems. Mn and Cr are involved in the development of each phase. Pyrochlore was decomposedand promoted densification at lower temperature on heating in Sb/Bi=1.0 system by Mn rather than Cr doping. A morehomogeneous microstructure was obtained in all systems affected by α-spinel. In ZBS(MnCr), the varistor characteristics wereimproved dramatically (non-linear coefficient, α=40~78), and seemed to form Vo.(0.33eV) as a dominant defect. Fromimpedance and modulus spectroscopy, the grain boundaries can be seen to have divided into two types, i.e. one is tentativelyassigned to ZnO/Bi2O3 (Mn,Cr)/ZnO (0.64~1.1eV) and the other is assigned to the ZnO/ZnO (1.0~1.3eV) homojunction.

A new manufacturing process of Fe-Cr-Al powder porous metal was attempted. First, ultra-fine fecralloy powders were produced by using the submerged electric wire explosion process. Evenly distributed colloid (0.05~0.5% powders) was dispersed on PU (Polyurethane) foam through the electrospray process. And then degreasing and sintering processes were conduced. In order to examine the effect of sintering temperature in process, pre-samples were sintered for two hours at temperatures of , , , and , respectively, in atmospheres. A 24-hour TGA (thermo gravimetric analysis) test was conducted at in a 79% +21% to investigate the high temperature oxidation behavior of powder porous metal. The results of the high temperature oxidation tests showed that oxidation resistance increased with increasing sintering temperature (2.57% oxidation weight gain at sintered specimen). The high temperature oxidation mechanism of newly manufactured Fe-Cr-Al powder porous metal was also discussed.