고층빌딩이나 해양 라이저와 같은 세장 구조물은 구조시스템의 동적 불안정의 주요 원인인 와류유기진동(vortexinduced vibration, VIV)에 의한 동하중에 매우 취약하다. 와류유기진동이 라이저의 고유진동수 영역에서 발생하는 경우 Lock-in현상으로 피로파괴의 우려가 있다. 본 논문에서는 Lock-in 영역에서 구조물과 유동의 동적거동에 대한 수치해석을 다루었으며, 유동조건 변화에도 불구하고 공진 주파수가 유지되는 현상에 대해 분석하였으며, 유입유동에 대해 수직방향으로 자유진동하는 1자유도의 2차원 원형실린더 단면에 대한 비정상 층류를 가정하였다. 각 시간 단계에서 물체의 움직임을 고려하여 유동장 격자를 재생성하며 비정상 유동과 물체의 운동에 대한 지배방정식을 순차적으로 수치해석하여 유체-구조연성해석을 수행하였다. 결과는 선행연구와 잘 일치함을 보여주었고, Lock-in 현상에 대한 특성을 잘 나타내었다. Lock-in 영역에서는 양력뿐만 아니라 항력도 크게 증가함을 보여주었으며, 실린더의 수직변위는 직경의 20%까지 이름을 나타내었다. 양력과 수직변위의 상관분석을 통해 실린더가 Lock-in 영역에서 양력과 수직변위의 위상차가 동기로부터 반동기로 천이함을 확인하였으며, 이러한 변화가 Lock-in 영역에서 나타나는 공진거동의 원인이 되는 것으로 판된되었다.

In this study, the heat flow characteristics of natural convection was theoretically analyzed with time by changing various locations of heat trace with tube surface about enclosed circular tube by applying nominal tube diameter 90 mm of KS D 3507. Before carrying out CFD (Computational Fluid Dynamics) analysis, it is presumed that the boundary condition is the tube’s inside and outside fluid temperature of 273 °K, the tube surface heat flux according to the heat trace location of 16 W/m. The result confirmed that water of inside tube is occurred natural convection caused by density difference depending on temperature profile. Additionally, in case of heat trace location, the heat transfer and flow characteristics showed clearly that two-heat trace location =135° and 180° was more favorable distribution than one-heat trace appropriate location =135°.

A series of injection and drainage test were conducted on an circular acrylic tube to investigate the pressure generated by the accumulated fill materials inside a circular acrylic tube structure. The acrylic tube was filled by means of gravity filling with a slurry material having an average water content of 700%. The water head during the filling process was 1.8m and the bottom pressure during initial filling was 20.18kPa. The recorded stress at the sides of the acrylic tube was 17.89kPa during the filling process and was reduced to 13.58kPa during the leaving process. Continuous drainage of the acrylic tube has greatly influenced the stresses around the tube structure. As the water is gradually allowed to overflow, the generated pressure at the topmost pressure sensor of the tube was reduced further to 2.17kPa. Eventually, the initially liquid state slurry material transforms into plastic state after water has dissipated and substantial soil particles are deposited in the acrylic tube. The final water content of the deposited silt inside the acrylic tube after the test was 42%. It was found that the state of stresses(geo-static earth pressures) in the acrylic tube was anisotropic rather than isotropic.

난류유동에 의한 소음은 계산비용의 관점에서 음향 상사법을 이용하여 전산유체 기법과 결합해 다양한 해석모델이 연구되고 있다. FW-H 음향상사법을 이용한 유동소음해석의 연구가 활발히 이루어지고 있으나, 기존 문헌들의 결과에서는 계산비용의 관점에서 난류유동에 의한 소음성분을 생략하고 있다. 그러나, 최근의 연구에서 유동소음특성에 있어 난류소음의 중요성이 밝혀진바 있다. 본 논문에서는 RANS 난류모델과 투과성 경계면을 이용한 Permeable FW-H 음향상사법을 이용한 난류유동소음해석에 대해 연구하였다. 2D 실린더에 대하여 직접적으로 변동압력을 추출하는 직접법과 난류성분을 고려하지 않은 FW-H 상사법, 또 난류소음의 성분을 포함하는 Permeable FW-H 방법의 경우를 비교하였다. Permeable FW-H 방법을 통해 일반적으로 적용되는 FW-H 방법에서 해석 불가능한 난류에 의한 소음의 영향을 기존의 FW-H 방법과 동일한 계산비용으로 예측할 수 있었고, 적절한 투과성 경계면 설정을 통해 높은 정확도의 해석이 가능했다. Permeable FW-H 방법을 통한 난류유동해석 절차를 확립하였으며, 그 유용성을 확인했다.

There are lots of and kinds of stone pagoda and stone Buddhas at Unjusa Temple in Hwasun, Jeonnam, which is thus called as Cheontap(千塔) or Cheonbul.(千佛) Several archaeological excavations have been conducted in Unjusa though, the foundation purpose or background motivation is yet wrapped in mystery. Circular shape is representative pagoda of Unjusa made of round frame or spherical roof but circular stone pagoda is unusual that there is no similar example found in India or China as well as in Korea. Located in the symbolic center, Circular stone pagoda is a key to understand Unjusa. Yundeung(輪燈) is made of stone for circular stone pagoda and there are craft lamp and large lamp. The large lamp, for the palace courtyard on the occasion of Palgwanhoe,(八關會) consists of discs and light on each disc. Outdoor lamp of circular stone pagoda made of stone for permanent preservation purpose. Unjusa is a very special temple with stone-yundeung for circular stone pagoda. In this study, a circular stone pagoda that is the source of yundeung said. Unjusa circular stone pagoda next to the title of 'yundeung pagoda' and proposes to call.

The plastic hinge region of RC pier ensures its nonlinear behavior during strong earthquake events. It is assumed that the piers secure sufficient strength and ductility in order to prevent the collapse of the bridge during strong earthquake. However, the presence of a lap-splice of longitudinal bars in the plastic hinge region may lead to the occurrence of early bond failure in the lap-splice zone and result in significant loss of the seismic performance. The current regulations for seismic performance evaluation limit the ultimate strain and displacement ductility considering the eventual presence of lap-splice, but do not consider the lap-splice length. In this study, seismic performance test and analysis are performed according to the cross-sectional size and the lap-splice length in the case of longitudinal bars with lap-splice located in the plastic hinge region of existing RC bridge columns with circular cross-section. The seismic behavioral characteristics of the piers are also analyzed. Based upon the results, this paper presents a more reasonable seismic performance evaluation method considering the lap-splice length and the cross-sectional size of the column.

In this paper, the wave run-up height and depression depth around air-water interface-piercing circular cylinder have been numerically studied. The Reynolds Averaged Navier-Stokes equations (RANS) and continuity equations are solved with Reynolds Stress model (RSM) and volume of fluid (VOF) method as turbulence model and free surface modeling, respectively. A commercial Computational Fluid Dynamics (CFD) software “Star-CCM+” has been used for the current simulations. Various Froude numbers ranged from 0.2 to 1.6 are used to investigate the change of air-water interface structures around the cylinder and experimental data and theoretical values by Bernoulli are compared. The present results showed a good agreement with other studies. Kelvin waves behind the cylinder were generated and its wave lengths are longer as Froude numbers increase and they have good agreement with theoretical values. And its angles are smaller with the increase of Froude numbers.

This paper presents the theoretical analysis for the flow driven by surface tension and gravity force in an inclined circular tube. The present study introduces detailed mathematical procedures for Casson viscosity model. The equations of velocity distribution and flow rate are developed to describe the displacement of a non-Newtonian fluid that continuously flew into a circular tube by surface tension. The equation of modified volumetric flow shows the complicated form of (10) due to yield stress term, and the equation of velocity distribution which includes the yield stress and inclination angle of circular tube is composed of terms of r and rc as form of (14).

One-dimensional flux theory (1DFT) is conventionally used for design of secondary clarifier of wastewater treatment plant. However, the 1DFT cannot describe turbulence, density current, shape parameters of the clarifier. In this study, we optimized the configurations of influent guide baffle and effluent baffle through the simulation using computational fluid dynamics (CFD) and its verification by particle image velocity (PIV) test. The energy dissipating inlet (EDI) without influent guide baffle (0°) showed the best efficiency for minimizing downward velocity under the center well of the clarifier. The lowest velocity distribution around the effluent weir region could be obtained with the McKinney baffle (EB-2). The performances of the influent and effluent baffles were clearly verified by PIV test results.

Tool tips of the circular saw for the steel cutting have commonly applied to brazing type welded the saw body to tips. In this case, when the tool tip is required to the exchange, many problems were occurred as the exchange cost is high and its time is long. In this study, to resolve the brazing type circular saw, the insert type circular saw has designed and made. Also, to confirm the performance of new type circular saw, the various experiments were carried out under condition of tip's shape and machining conditions.

This paper presents the theoretical analysis for the flow driven by surface tension and gravity force in an inclined circular tube. The governing equation is developed to describe the displacement of a Newtonian fluid that continuously flew into a circular tube by surface tension, which represents a second-order, nonlinear, nonhomogeneous and ordinary differencial form. It was found that the theoretical predictions of the governing equation were excellent agreement with the unsteady state solutions for horizontal tube and the results of force balance equation for steady state.

Because of the inherent flexibility in their design for improved material properties, composites have wide applications in aerospace vehicles and automobiles. The purpose of this study is to investigate the energy absorption characteristics of CFRP(Carbon Fiber Reinforced Plastics)tubes on static and impact tests. Static compression tests have been carried out using the static testing machine(Shin-gang buckling testing machine)and impact compression tests have been carried out using the vertical crushing testing machine. When such tubes were subjected to crushing loads, the response is complex and depends on the interaction between the different mechanisms that control the crushing process. The collapse characteristics and energy absorption were examined. Trigger and interlaminar number affect the energy absorption capability of CFRP tubes.

It is known that seismic performance of existing bridges having insufficient lateral confinements and lap-splices of longitudinal reinforcements at the base of column decreases dramatically. In this study, small-scaled model tests have been performed to confirm the seismic behaviors of RC bridge piers with various lap-splice lengths. The 8 test models have circular section with diameters of 0.65 m, 0.8 m, 1.0 m, and lap-splice lengths of B-class or C-class. The test results show that the failure modes of models are not depending on the lap-splice length itself but depend on the ratio of lap-splice length to diameter, and that the displacement ductility is also affected by this ratio.

이 연구는 국내 원형교차로에서 발생한 교차로 사고를 다루고 있다. 연구의 목적은 ZAM을 이용하여 원인별 사고모형을 개발하는데 있다. 주요결과는 다음과 같다. 첫째, 교차로 운행방법 위반에서는 ZINB 모형이 적합한 것으로 분석되었다. 둘째, 안전거리 미확보에서도 ZINB 모형이 적합한 것으로 분석되었다. 마지막으로 공통변수로는 교통량과 회전차로 폭이 선정되었다. 교통량이 많을수록 그리고 회전차로 폭이 좁을수록 사고가 많이 발생하는 것으로 분석되었다. 특정변수로는 접근로수와 감속 시설수가 채택되었고, 접근로수가 증가할수록 그리고 감속시설수가 적을수록 사고가 증가하는 것으로 분석되었다. 이 연구는 원형교차로 사고연구에 기여할 것으로 기대된다.

이 연구의 목적은 중공원형 철근콘크리트 교각의 횡방향철근에 따른 지진거동을 파악하고 합리적이면서 경제적인 내진 설계기준의 개발을 위한 자료를 제공하는데 있다. 3개의 중공원형 교각 실험체에 일정 축하중 하에서 횡방향 반복하중을 가하는 준정적실험을 수행하였다. 정확하고 올바른 성능평가를 위하여 신뢰성 있는 비선형 유한요소해석 프로그램을 사용하였다. 이용된 해석기법은조사된 실험체에 대하여 하중단계에 따라 내진성능을 비교적 정확하게 예측하였다. 실험적, 해석적 결과로부터 중공원형 철근콘크리트교각의 설계와 시공 실무를 향상하기 위한 내진상세를 제시하였다.

이 연구의 목적은 결합원형띠철근을 갖는 철근콘크리트 교각의 내진성능을 파악하는데 있다. 3개의 인터락킹 교각 실험체에 일정 축하중 하에서 횡방향 반복하중을 가하는 준정적 실험을 수행하였다. 사용된 프로그램은 철근콘크리트 구조물의 해석을 위한 RCAHEST이다. 사용된 해석기법은 조사된 실험체에 대하여 하중단계에 따라 성능을 비교적 정확하게 예측하였다. 실험적, 해석적 결과로부터 결합원형띠철근을 갖는 철근콘크리트 교각의 설계와 시공 실무를 향상하기 위한 상세를 제시하였다.

이 논문은 사고유형에 따른 교통사고를 다루고 있다. 연구의 목적은 두 가지 사고유형의 특성을 분석하고, 유형별 모형을 개발하는데 있다. 이를 위해 이 연구는 두 집단 사이의 차이점을 분석하고, 국내 원형교차로 자료를 사용하여 포아송 및 음이항 회귀모형을 개발하는데 그 목적이 있다. 주요 결과는 다음과 같다. 첫째, 차대차 사고가 73.41%로 가장 많은 비중을 차지하는 것으로 분석되었다. 둘째, 차대사람과 차대차 사고건수 및 EPDO를 종속변수로 통계적으로 의미 있는 2개의 포아송 모형과 2개의 음이항 모형이 개발되었다. 셋째, 사고유형별 심각도모형의 공통변수는 교통량, 그리고 특정변수로는 우회전 별도차로 수, 과속방지턱, 진출입구 수 및 횡단보도 수가 채택되었다.