Background: Lumbopelvic stability is highly important for exercise therapy for patients with low back pain and shoulder dysfunction. It can be attained using a pelvic compression belt. Previous studies showed that external pelvic compression (EPC) enhances form closure by reducing sacroiliac joint laxity and selectively strengthens force closure and motor control by reducing the compensatory activity of the stabilizer. In addition, when the pelvic compression belt was placed directly on the anterior superior iliac spine, the laxity of the sacroiliac cephalic joint could be significantly reduced.
Objects: This study aimed to compare the effects of EPC on lumbopelvic and shoulder muscle surface electromyography (EMG) activities during push-up plus (PUP) and deadlift (DL) exercise, trunk extensor strength during DL exercise.
Methods: Thirty-eight subjects (21 men and 17 women) volunteered to participate in this study. The subjects were instructed to perform PUP and DL with and without the EPC. EMG data were collect from serratus anterior (SA), pectoralis major (PM), erector spinae (ES), and multifidus (MF). Trunk extensor strength were tested in DL exercise. The data were collected during 3 repetitions of all exercise and the mean of root mean square was used for analysis.
Results: The EMG activities of the SA and PM were significantly increased in PUP with pelvic compression as compared with PUP without pelvic compression (p<.05). In DL exercise, a significant improvement in trunk extensor strength was observed during DL exercise with pelvic compression (p<.05).
Conclusion: The results of this study indicate that lumbopelvic stabilization reinforced with external pelvic compression may be propitious to strengthen PUP in more-active SA and PM muscles. Applying EPC can improve the trunk extensor strength during DL exercise. Our study shows that EPC was beneficial to improve the PUP and DL exercise efficiency.
곡률을 갖고 있는 쉘 부재들은 선박 및 육상구조 내에서 캠버와 선수, 선미, 파이프 및 저장용 탱크에 주로 사용되고 있다. 이러한 곡률 쉘 부재들은 기본적으로 원통형 실린더 부재의 일부라고 간주할 수 있다. 일반적으로 곡률의 존재는 압축하중 작용 시 좌굴강 도 및 최종강도를 증가시키는 것으로 알려져 있다. 본 논문에서는 이러한 영향을 확인하기 위하여 탄성대변형 시리즈해석을 수행하였으며, 매개변수의 영향을 분석하였다. 실린더의 최종강도 거동은 초기처짐과 해석모델링 방법에 큰 영향을 받는 것을 확인하였다.
PURPOSES: It is difficult to estimate tunnel stability because of lack of timely information during tunnel excavation. Tunnel deformability refers to the capacity of rock to strain under applied loads or unloads during tunnel excavation. This study was conducted to analyze a methods of pre-evaluation of stability during tunnel construction using the critical strain concept, which is applied to the results of tunnel settlement data and unconfined compression strength of intact rock or rock mass at the tunnel construction site.
METHODS: Based on the critical strain concept, the pre-evaluation of stability of a tunnel was performed in the Daegu region, at a tunnel through andesite and granite rock. The critical strain concept is a method of predicting tunnel behavior from tunnel crown settlement data using the critical strain chart that is obtained from the relationship between strain and the unconfined compression strength of intact rock in a laboratory.
RESULTS: In a pre-evaluation of stability of a tunnel, only actually measured crown settlement data is plotted on the lower position of the critical strain chart, to be compared with the total displacement of crown settlement, including precedent settlement and displacement data from before the settlement measurement. However, both cases show almost the same tunnel behavior. In an evaluation using rock mass instead of intact rock, the data for the rock mass strength is plotted on the lower portion of the critical strain chart, as a way to compare to the data for intact rock strength.
CONCLUSIONS : From the results of the pre-evaluation of stability of the tunnel using the critical strain chart, we reaffirmed that it is possible to promptly evaluate the stability of a tunnel under construction. Moreover, this research shows that a safety evaluation using the actual instrumented crown settlement data with the unconfined compression strength of intact rock, rather than with the unconfined compression strength of a rock mass in the tunnel working face, is more conservative.
Fiber reinforced polymeric plastic (FRP) materials have many advantages over conventional structural materials, i.e., high specific strength and stiffness, high corrosion resistance, right weight, etc. Among the various manufacturing methods, pultrusion process is one of the best choices for the mass production of structural plastic members. Since the major reinforcing fibers are placed along the axial direction of the member, this material is usually considered as an orthotropic material. However, pultruded FRP (PFRP) structural members have low modulus of elasticity and are composed of orthotropic thin plate components the members are prone to buckle. Therefore, stability is an important issue in the design of the pultruded FRP structural members. Many researchers have conducted related studies to publish the design method of FRP structures and recently, referred to the previous researches, pre-standard for LRFD of pultruded FRP structures is presented. In this paper, the accuracy and suitability of design equation for the local buckling strength of pultruded FRP I-shape compression members presented by ASCE are estimated. In the estimation, we compared the results obtained by design equation, closed-form solution, and experiments conducted by previous researches.
Pultruded FRP can be regarded as an orthotropic material due to its manufacturing process that pull-out fibers impregnated with polymeric resin, which is suitable to produce structural member with unlimited lengths of reinforced polymer structural shapes with a various shape of cross-section. However, fiber distribution in the cross-section is not uniform because of the characteristics of pultrusion process. Therefore, random fiber distribution causes the difference of the modulus of elasticity throughout the cross-section. In this paper, closed-form local buckling analysis is conducted on the pultruded FRP I-shape compression members. The mechanical properties used to analytical investigations are obtained from the coupon test. The coupon test specimens are taken from the pultruded FRP I-shape member. Moreover, the local buckling tests of pultruded FRP I-shape members are conducted and test results are compared with the analytical results.
This study is aimed to examine the influence of the rotational stiffness of U-shaped ribs on the local buckling behaviors of laminated composite plates. Applying the orthotropic plates with eight layers of the layup [(0°)4]s and [(0°/90°)2]s, 3-dimensional finite element models for the U-rib stiffened plates were setup by using ABAQUS and then a series of eigenvalue analyses were conducted. There is a need to develope a simple design equation to establish the rotational stiffness effect, which could be easily quantified by comparing the theoretical critical stress equation for laminated composite plates with elastic restraints based on the Classical laminated plate theory. Through the parametric numerical studies, it is confirmed that there should clearly exist an increasing effect of local plate buckling strength due to the rotational stiffness by closed-section ribs. An applicable coefficient for practical design should be verified and proposed for future study. This study will contribute to the future study for establishing an increasing coefficient for the design strength and optimum design of U-rib stiffened plates.
이 연구는 새로운 형태의 FRP-콘크리트 합성말뚝인 하이브리드 CFFT(HCFFT)를 개발하는 과정의 일부이다. 이 논 문에서는 CFFT와 HCFFT의 압축강도실험을 통하여 구조적 거동을 분석하였다. 압축강도실험에 앞서 PFRP와 FFRP 재료의 역학적 성질을 조사하였다. HCFFT 압축강도실험은 콘크리트 강도와 FFRP의 두께를 변수로 하여 실험을 수 행하였다. 그리고, FFRP 두께를 변수로 PFRP를 제외한 CFFT 실험체를 제작하고 실험을 수행하여 HCFFT와 비교· 분석하였다. 실험 결과, HCFFT의 압축강도는 CFFT에 비하여 11~47% 향상되는 것으로 나타났다. 실험구간내의 필 라멘트 와인딩 FRP 보강두께의 증가에 따른 HCFFT의 압축강도는 선형으로 증가시키는 것으로 나타났다. 또한 실 험체와 동일한 조건의 유한요소해석을 수행하였다. 해석결과는 실험결과에 비하여 모든 시편에서 약간 작은 값을 보였으며, 0.14%에서 17.95%까지의 오차범위 내에 있음을 알 수 있었다.
이 논문에서는, CFT 감재-콘크리트 합성말뚝과 FRP를 원주방향으로 보강한 FRP-콘크리트 합성말뚝 (CFFT)과 관련 하여 발생하는 문제점들을 완하시키기 위해 새롭게 제안된 콘크리트 채움 원형 FRP 말뚝 (HCFFT)의 구조적 거동 에 대한 실험적 연구결과를 발표하였다. 연구를 통해 기존의 CFT와 CFFT 말뚝과 비교하여 새로 제안한 HCFFT 말 뚝이 말뚝 기초의 시공에서 축하중과 휨모멘트를 포함하는 상부하중을 지반에 효과적으로 전달할 수 있음을 알 수 있었다.
국민소득수준의 향상에 따라 국내 건축물의 디자인 및 사용목적의 대한 다양성이 요구되고 있다. 대공간 구조물은 이러한 시대적 요구에 적합한 구조물로서 최근 대공간 구조물에 대한 설계 및 시공법에 관한 관심이 꾸준히 증가하고 있다. 트러스구조는 대공간 구조에 보편적으로 사용되는 구조시스템으로 트러스의 부재는 단면의 효율이 높은 강관을 사용하는 것이 일반적이다. 현재 국내에 유통되고 있는 강관은 생산처에 따라 다양한 제품이 생산되고 있으나 강관 소재의 출처 및 강관 자체의 실제 성능에 관한 연구는 미비한 실정이다. 이 연구는 국내에 유통되고 있는 일반구조용 각형강관, 원형강관 및 비계용 강관에 대하여 소재의 인장시험과 Stub-column 압축시험 및 기둥의 좌굴실험을 통해 강관의 소재성능 및 구조부재로서의 압축성능을 파악하는 것을 목적으로 한다. 소재시험결과, 구입처 구분 및 단면형상에 따른 강관 소재성능의 편차가 확인되었다. 기둥좌굴 실험결과, 각 실험체의 압축내력은 LSD 기준곡선에 만족하는 결과를 나타내었으며, SSRC 곡선1, ECCS-a곡선에 상회하는 결과를 나타내었다.
보강판은 선박이나 해양구조물에서 폭넓게 사용되고 있는 기본적인 강도 부재이다. 이러한 보강판은 선박의 갑판부, 선측부, 선저부에 흔히 사용되고 있다. 보강판은 보강재가 어느 한 방향으로 또는 양방향으로 구성되어 있으며 후자에 대해서 보통 그릴리지라고 한다. 보강판의 좌굴 및 소성붕괴는 선각거더의 파손 원인이 되므로 좌굴 및 최종강도가 정확하게 규명할 필요가 있다. 본 연구에서는 범용유한요소해석코드인 ANSYS를 이용하여 좌굴 및 좌굴 후 거동에 대한 평가를 수행하고 보강재 치수변화, 수압의 영향을 고려하여 압축최종강도에 대해 해석 수행하였다.
In this study, the changes in compressive strength of steel tubular short columns with local corrosion is investigated using a finite element approach. The dimensions of the local corrosion are defined by its depth (0, 1.5, 3, 4.5 and 6 mm), height (0, 20, 40, 60, 80, 100, 120, 140, 160 and 180 mm), circumference (0, 90, 180, 270 and 360°) and location of damage along the steel tubular short column. There are 42 finite element models executed in this study that are categorized as Type A, Type B and Type C specimens. The results of the finite element models were compared against the previous experimental tests for model validation. Moreover, a parametric study was used to study the effect of the corrosion depth, height and circumference to the compressive strength of a steel tubular short column. Comparing the results of the finite element analysis, experimental and calculated compressive strengths, the percentage error is found to be within 10%.
For the purpose of increasing slab span, new composite beam with U-shaped compression element consisting of channel and concrete has been developed. Strength design procedures of the composite beam against construction and permanent loads have been proposed. Using these procedures, it is possible to design consistently of the developed composite beam.
In this study, cement mortar (KS F 4042) used for repairing concrete structures was evaluated for compressive strength and bond strength according to the mixing ratio of polymer. From the experimental results, it was confirmed that as the polymer content increases, the bond strength properties increase, but the compressive strength decreases slightly at a certain rate.
In this study, cement mortar (KS F 4042) used for repairing concrete structures was evaluated for compressive strength and bond strength according to the mixing ratio of polymer. From the experimental results, it was confirmed that as the polymer content increases, the bond strength properties increase, but the compressive strength decreases slightly at a certain rate.
Steel box girder has not only an excellent constructability but is also a lightweight structure. Compression flanges of steel box girder under negative moment need stiffeners to increase buckling strength, thereby increasing the construction cost. In this study, compression flanges using trapezoidally bended plates were investigated to replace existing flat flanges.
콜드체인용 골판지 상자의 냉기공과 상자의 압축강도와의 관계를 알아보고자, 골판지 상자에 각각 냉기공을 2 또는 3개를 뚫고, 냉기공의 크기와 면적을 달리하여 상온(RH 705 %)에서 4주간 저장하면서 골판지 상자의 압축강도를 측정하였다. 냉기공 면적이 4, 7, 10 %모두에서 냉기공의 크기가 폭은 좁고 길이가 긴 것이 압축강도가 높게 나타났다. 또한 냉기공 면적에 따른 압축강도를 살펴보면 냉기공 면적이 4 %인 상자가 다른 상자들에 비해 압축
In order to find effective linerboard compositions for the corrugated fibreboard containers for apples, we have evaluated the strength and the cost effectiveness of the various linerboards and corrugated fibreboard containers. From the results, we suggest SC240, WLK210 or SK180 for the outer liners, M180 to M250 for the mediums, and K2200 or Al80 for the inner liners, respectively. Furthermore, we recommend two cost effective types of corrugated fibreboard compositions, SC240/S120/S120/M160/A180 for the white face liners, and SK180/M180/S120/M180/A180 for the color face liners. Evidence has been presented to support the conclusion that the new high compression strength corrugated fibreboard containers have better performance in the compression and bursting strength tests, while reducing material costs by thirty four percents.
The compression strength of the corrugated fiberboard boxes is very important information to the manufacturers and the end users. The computer program being used to design the compression strength of the boxes was developed by using Korean Standards for the corrugated fiberboard box and some other data. The developed computer program could be applied to only the boxes produced according to the Korean Standards. Also this program needs to be revised continuously by the newly added and developed data.