본 연구에서는 미생물 첨가에 따라 거세한우 비육우 분의 이화 학적 특성, 미생물 성상, 가스발생량 및 퇴비 부숙도에 미치는 영 향을 규명하고자 수행하였다. 이상의 결과를 종합하면, 4주 후,미생물 첨가구에서 수분, 유기물, 총질소 함량 및 pH가 낮았으며, 나머지 이화학적 특성에서는 차이가 나타나지 않았다. 유산균과 효모균 수는 증가하였으며, 대장균 수는 감소하였다. 12주 후, 미 생물 첨가구에서 유산균과 고초균 수는 높았으나, 수분, 효모 및 대장균 수는 낮게 낮았다. 하지만 암모니아, 황화수소 발생량과 퇴비 부숙도는 미생물 첨가에 의한 효과가 나타나지 않았다. 따라 서, 거세한우 분에 미생물을 첨가하면 유익균은 증가하고, 병원성 미생물은 감소하여, 비육우의 생산성은 증진될 것으로 사료되지 만, 가스 발생량 및 퇴비 부숙도에 대한 추가적인 연구는 지속적 으로 수행되어야 할 것으로 사료된다.

본 연구에서는 광화학 대기질 모델인 CMAQ을 활용해 화력발전소 배출량 제거에 따른 O3 농도의 변화 특성을 분석하였다. 하동 화력발전소를 대상으로 주변 지역의 O3 농도 변화에 대한 발전소 배출량의 영향을 조사하기 위해 하 동 화력발전소의 배출량 제거 전과 후의 CMAQ 수치 모의를 수행하였다. 수치 모의 결과 O3의 주요 전구 물질인 NOx (-18.87%)와 VOCs (-11.27%)의 농도가 감소한 반면에 O3 (25.24%)의 농도는 증가한 것으로 나타났다. 화력발전소 배출량 제거로 인한 NO와 O3 농도의 상대적인 변화를 비교해 본 결과 높은 음의 상관관계(R= -0.72)를 나타내는 것이 확인되었다. 이러한 결과는 O3의 농도 증가가 NO 농도 감소로 인한 O3의 적정 효과 완화로 설명 될 수 있음을 의미한 다. 해당 지역의 O3의 농도 증가가 NO의 농도 감소에 주로 영향을 받은 이유는 해당 지역이 VOC-limited (i.e., NOxsaturated) 지역이기 때문으로 분석되었다. 이러한 결과는 특정 지역의 O3의 농도가 단순히 배출량의 증감에 따라 비례하게 나타나지 않을 수 있다는 것을 암시한다. 따라서 화력발전소 배출량 저감 조치로 인한 대기 중 O3 농도 개선 효과를 정확히 예측 및 평가하기 위해서는 지역 별 O3의 생성 및 소멸 기작에 대한 심도 있는 이해가 필요하다.

In this study, real-time monitoring of air quality using a real-time mobile monitoring system was conducted to identify the emission characteristics and current status of air pollutants and odorous substances that are mainly generated in domestic dyeing industrial areas and to trace the pollutant sources. The concentration of toluene in the industrial area was detected up to 926.4 ppb, which was 3 to 4 times higher than that of other industrial areas. The concentration of methylethylketone was 124.7 ppb and the concentration of dichloromethane was 129.5 ppb. Acrolein concentration was highest at E point at 521.6 ppb, methanol concentration was highest at D point at 208.8 ppb, and acetone concentration was highest at M and N points at 549.3 ppb. The most frequently detected concentration of pollutants in the air quality monitoring results in the industrial area was, in descending order, toluene > methanol > acrolein > dichloromethane > acetone, which was similar to the chemical emissions used in the industrial area by the Pollutant Release and Transfer Register data. The concentration of odorous substances measured in real time was compared with the concentration of minimum detection, and the concentration of hydrogen sulfide was about 10 times higher than the concentration of minimum detection at A point, which was judged to be the main odorous cause of A point. In the future, if the real-time mobile measurement system is constructed to automatically connect wind direction/wind speed, PRTR (Pollutant Release and Transfer Register) data and SEMS (Stack Emission Management System) data, etc., it was judged that more accurate monitoring could be performed.

The purpose of this study is to investigate the level of ELF-MF emissions from underground cable lines near daycare centers in the metropolitan city of Seoul. We investigated 143 daycare centers from June to September of 2015. In addition, the rate of reduction of ELF-MF levels according to the distance from the line was calculated using simulations. The ELF-MF emission level of 143 daycare centers at boundary point was 1.37 ± 1.75 mG (GM: 0.75 mG) and at direct point was 11.14 ± 17.99 mG (GM:6.05 mG). ELF-MF levels at direct point were 8.13 (arithmetic mean) and 8.06 (geometric mean) times higher, respectively, than that at the boundary point. By analyzing the relationship between ELF-MF and electricity current (A) and operating depth (m), a significant correlation was found between ELF-MF and current (A) and depth (m), at 0.360 (p<0.01) and -0.303 (p<0.05), respectively. The results of the simulation showed that appropriate separation distances showing below 4 mG was 8m and 14m, adjusted mean current (A) and maximum current (A), respectively. The results of the study suggest that a plan should be implemented for the management of ELF-MF in High voltage power-line and Underground cable line areas, through a broad and detailed survey and risk communication.

최근 지구 온난화는 세계 경제발전으로 화석연료 사용이 주범으로 인식하고 있다. 이러한 화석연료를 감소하기 위한 연구는 여러 대체에너지 산업으로 발전하고 있으며, 그 중 우리나라에서 생산할 수 있는 연료는 바이오연료이다. 바이오연료는 화석연료에 의해서 발생하는 환경오염 문제를 줄이면서 경제적인 이익을 주는 지속 가능한 연료이다. 그래서 바이오연료를 친환경에너지로 전환시키는 재생에너지 등에 많은 연구가 진행되고 있다. 따라서 본 실험은 어선에서 사용했던 기관을 다시 리모델링하여 실험장치를 직접 제작 설치하였고, 여러 바이오연료를 사용하여 선박의 경제적이고 친환경적인 운항에 도움을 주고자 연구하였다. 유채유, 대두유, 폐유채유의 배기배출물특성에 미치는 영향을 종합적으로 분석한 결과는 연료의 물리적, 화학적 성분이 비슷하여 선박용 엔진에 사용이 가능하고, 연료소비율과 NOx는 약간 증가하였으나, 매연은 많이 감소하는 경향이 확인되었다.

This experimental work was performed to reveal the effect of intake air temperature on the improvement of performance and exhaust emissions in a SI engine. To achieve this, fuel consumption rate, combustion pressure, rate of heat release, and reduction of exhaust emissions were measured and compared in 4-cylinder spark ignition engine. It was founded that lower intake air temperature can lead higher combustion pressure and heat release rate due to the higher intake air flow rate, volumetric efficiency, and fuel consumption rate. At the same time, higher intake air temperature leads to the longer ignition delay time, therefore, retarded ignition of engine was observed. Lower CO and HC values were also observed as the intake air temperature increases.

본 연구에서는 균질기에 의해 혼합된 물과 벙커-A를 보일러로 연소하였을 때의 배기 배출물 특성에 대해 연구를 수행하였다. 그 결과로 균질기로 균질화 된 벙커-A의 경우, 순수 벙커-A에 비해 NOx 농도는 19 %, CO 농도는 54 % 감소를 나타냈다. 물-벙커A의 경우 물 혼합 비율이 증가할수록 NOx 농도분포가 낮아지는 것을 확인할 수 있었다. 특히, 20 %물-80 %벙커-A의 경우 순수한 벙커-A 보다 배기가스 내 NOx 농도가 45 %까지 감소하였다. 그러나 20 %물-80 %벙커-A의 경우, CO농도 분포는 불규칙한 변화를 나타냈다. 이것은 일정량 이상의 물 혼합은 보일러의 연소 성능 저하 원인이 될 수 있다는 것을 의미한다. 이 결과로부터 본 연구에서 보일러의 정상 연소를 위한벙커A유 내 물의 한계 혼합율은 15 % 인 것을 알 수 있었다. 연돌 부근에서 채취한 매연 부착양은 물의 혼합율이 증가할수록 감소하였다.

In order to test the applicability of bunker-A in a diesel engine for small-fishing boat, the investigation of the engine performance and the exhaust emission was performed under various conditions of fuel property, intake air pressure and fuel temperature. It was also performed based on IMO NOx Technical code. At high load, the energy consumption rate of bunker-A was lower than that of diesel oil, and the characteristics of exhaust emission of bunker-A were similar to those, and NOx emission rates of both fuels satisfied the IMO NOx emission regulation limits. The energy consumption rate and characteristics of exhaust emission were improved as the intake air pressure was increased, but these were not improved remarkably as the temperature of bunker-A was heated. However, at low load the energy consumption rate, CO emission rate and HC emission rate of bunker-A were higher than those of diesel oil, but NOx emission rates of the fuels were about the same. In addition, at low load the energy consumption rate and CO emission rate of bunker-A were increased as the intake air pressure and the temperature were higher than normal conditions. Accordingly, it is thought that the use of bunker-A in a kind of test engine is possible at high load. On the other hand, it is thought that more research is needed to improve the combustion efficiency under low temperature and low load condition.

This paper investigates tensile characteristics of the stress aging heat-treated SM45C steel which are aging temperature at 250℃, 300℃, aging time at 1, 3 hours, and applied load at 300, 400N conditions by using acoustic emission. Most suitable aging condition was aging temperature 300℃, aging time 1 hour, and aging applied load 300N. And increased yield load 28.3% than non-treatment specimen in this condition. AE energy in elastic limit increased about 16.7 times than non-treatment specimen. When aging time is 3 hours, yield load decreased than other conditions that possibility is high to have itself defect on inside the specimen or coarse grain size precipitation is different in happened over-aging phenomenon. Especially, in case of 300℃, 3 hours and 400N condition appeared AE energy in elastic limit fairly high about 30 times than non-treatment specimen. This is considered by emit a lot of energies when material causes plastic deformation because the ductility increases on specimen by over-aging phenomenon.

산유국으로부터 에너지 독립을 하고 대기오염방지를 위한 배기배출물을 저감시키기 위하여 대체연료에 많은 관심을 가지고 있다. 폐유나 새로운 식물성 기름과 동물성 기름으로부터 생성할 수 있는 바이오디젤유가 압축점화기관인 디젤기관에 구조적인 변화없이 사용될 수 있다. 이 논문에서는 4행정 직접분사식 디젤기관을 이용하여 순수 디젤유와 바이오디젤 혼합유(바이오디젤 10% 및 20% 함유)의 연료소비율과 배기배출물에 미치는 영향을 제시했으며, 특히 실험에 사용된 바이오디젤 연료는 우리 실험실에서 유채유로부터 직접 생산되었다. 이 연구 결과 바이오디젤 혼합유가 디젤유 보다 연료소비율과 질소산화물은 약간 증가 되었고 일산화탄소와 매연은 상당히 감소되었다.

Building materials are composed of very complex chemical compounds. The aims of this paper are to investigate the emission concentrations of indoor pollutants from new apartment house and the emission variation patterns during 75 days. The average value of total volatile organic compounds(TVOCs) concentration was 3,768 ㎍/㎥ in five new apartments. Major VOCs included toluene, ethylbenzene, m,p-xylene and o-xylene. The average concentrations of each compound were measured as : benzene(58㎍/㎥), toluene (793㎍/㎥), ethylbenzene(438㎍/㎥), styrene(79㎍/㎥), m,p-xylene(1,210㎍/㎥), o-xylene(364㎍/㎥). The results indicated that the major VOCs from the new apartment were affected by building products such as on aromatic hydrocarbon compounds. TVOCs emission are characterized as high emission level at initial time (12,856㎍/㎥) and decreased through time. After a lapse of 75 days in sample house, TVOCs concentration decreased in about 20 times as compared with the initial concentration. The TVOCs emission profiles strongly depended on the generation mode and the concentration of the VOCs in building material.

The purpose of this study was to investigate the concentration of aldehydes from new apartments in three cities(Suncheon, Yeosu, and Gwangyang) of Chonnam region. The target apartments were within 3 months after the completion of construction. Aldehydes were sampled using 2,4-DNPH cartridge and analyzed by HPLC. Temperature and relative humidity were monitored continuously every one minute by digital temperature and hygrometer. As the concentration ratio of formaldehyde between back-up and front cartridge was 3.94 6.97%, the 2,4-DNPH cartridge method satisfied a breakthrough problem for the sample collection. The repeatability of retention time and peak area for HPLC were excellent as 0.5 and 1.5%, respectively. The upper floor of S apartment (16 pyong) showed the highest concentration of formaldehyde as 1,093㎍/㎥. The average concentration of formaldehyde was the highest in K apartment(52 pyong) as 1,045㎍/㎥. The average concentration of formaldehyde in S apartment(16 pyong) and C apartment(25 pyong) were 872.6㎍/㎥ and 737.5㎍/㎥, respectively. The I/O ratios of formaldehyde were 56.9 60.0(mean : 59.1), 37.9 43.3(mean : 39.8) and 18.3 29.3(mean : 23.3) in K, C and S apartment, respectively. Therefore, it is believed that the indoor concentration of formaldehyde was very serious in new apartment. From these results, it is important that building material which emit low indoor pollutant should be selected for new apartments. In addition, management program for indoor air, such as using an adequate amount of adhesives, should be considered and indoor optimum condition should be maintained in new apartments.

IPCC Guidelines have been updated after the first official announcement to get more precise estimation of GHG emissions. The goal of this study is to evaluate the implications of the IPCC Guidelines improvements including equations of country-specific parameter values for estimating GHG emissions for rice cultivation on the agricultural sector. In addition, we analyze the effects of emission factors associated with organic amendment applications. The results of this study are as follows; (1) the total GHG emissions of rice cultivation based on 1996 IPCC GL are 28% lower than those estimated by 2006 IPCC GL with the same year data; (2) GHGs can be reduced up to 60% through the assumption of organic fertilizer applications; (3) Jeonnam and Chungnam are the worst regions for GHG emissions on rice cultivation and Chungbuk shows the highest reduction rate of GHG emissions, about 40%.

The impact of a considerable increase in traffic volume on the emission and concentrations of air pollutants was investigated at three beaches (Haeundae (HB), Gwanganri (GB), and Songjeong (SB)) in Busan during beach opening period (BOP) in 2011. During the BOP, passenger car was the major vehicle type, followed by taxi, and van. CO was the major contributor of total air pollutant emissions followed by NOx, VOC, and PM10. For the temporal variation of the emission of air pollutants during the BOP, it was generally the highest in the afternoon followed by the evening and morning, except for SB. For the spatial variation of their emission, it was the highest at GB followed by SB and HB. The emissions of air pollutants during the BOP were generally higher than those during the Non-BOP, except for HB. In contrast, the significant impact of the traffic volume increase on the concentrations of air pollutants at monitoring sites near the three beaches during the BOP were not found compared to the Non-BOP due to the significant distances between monitoring sites of air pollutants and monitoring sites of traffic volume at the beaches.