This study deals with the application of an artificial neural network (ANN) model to predict power consumption for utilizing seawater source heat pumps of recirculating aquaculture system. An integrated dynamic simulation model was constructed using the TRNSYS program to obtain input and output data for the ANN model to predict the power consumption of the recirculating aquaculture system with a heat pump system. Data obtained from the TRNSYS program were analyzed using linear regression, and converted into optimal data necessary for the ANN model through normalization. To optimize the ANN-based power consumption prediction model, the hyper parameters of ANN were determined using the Bayesian optimization. ANN simulation results showed that ANN models with optimized hyper parameters exhibited acceptably high predictive accuracy conforming to ASHRAE standards.

This study deals with the maximum thermal load analysis and optimal capacity determination method of tank culture system for applying seawater source heat pump to save energy and realize zero energy. The location of the fish farm was divided into four sea areas, and the heat load in summer and winter was analyzed, respectively. In addition, two representative methods, the flow-through aquaculture system and the recirculation aquaculture system were reviewed as water treatment methods for fish farms. In addition, the concept of the exchange rate was introduced to obtain the maximum heat load of the fish farms. Finally, power consumption for heat pumps was analyzed in the view point of sea areas, tank capacity, and exchange rate based on the calculated maximum thermal load.

Welding is one of representative manufacturing processes in the industrial field. Cryogenic storage containers are also manufactured through welding, and conversion to laser welding is issue in the field due to many advantages. Since welding causes thermal-elastic deformation, design considering distortion is required. Prediction of distortion through FEM is essential, but laser welding has difficulties in the field because there is no representative heat source model. The author presented the model that can cover various models using a multi-layer heat source model in previous studies. However the previous study has a limitation which is a welding heat source model must be derived after performing bead on plate welding. Thus this study was attempted to estimate the welding heat source parameters by comparing the shape of bead under various conditions. First, the difference between penetration shape and welding heat source parameters according to welding power was analyzed. The radius of the welding heat source increased according to the welding power, and the depth of the welding heat source also increased. The correlation between the penetration shape and the welding heat source parameter appears at a similar rate, however the follow-up research is necessary with more model data.

Due to environmental pollution, regulations on fossil fuels are required. There is a movement for the regulations by using LNG fueled propulsion ships. LNG is an eco-friendly fuel that does not emit NOx or SOx during combustion, but its boiling point is -163°C. Under that condition, the use of metal is restricted, and IMO defined applicable materials through IGC code. Among the metals, 9% nickel steel is one of excellent mechanical properties such as yield strength and tensile strength in cryogenic condition. Thus 9% nickel steel is widely used in cryogenic storage containers for ships. In addition, laser welding, which minimizes thermoelastic distortion by applying a concentrated heat source to a narrow area for a short period of time, is in the spotlight. So, this study is a basic research to predict and respond to thermal distortion during laser welding. Secondary version of the representative heat source model was derived through the author's previous research with STS304L, and the heat source model was derived by applying the heat source model to 9% nickel steel in this study. 9% nickel steel is a material that is in high demand and is widely used in the manufacture of cryogenic containers, so this study is expected to be able to respond immediately to the field.

9% nickel steel has remarkable mechanical properties in a cryogenic condition and is widely used in storage containers for LNG fueled ships. Demand for laser welding rather than conventional arc welding has grown to increase manufacturing efficiency. However there are various types of heat sources which are suggested by other researchers. With that, it is difficult to select a proper heat source shape for welding conditions. The author proposed a representative heat source model that can cover most of suggested heat source models through previous studies. Welding power was fixed at 4kW and the speed was changed to 1.0m/min, 1.5m/min, and 2.0m/min respectively. The shapes of the welding heat sources were derived, and the tendency of the main parameters was also deducted. It was observed that the width and depth of the weld bead decreased as the welding speed increased through welding experiment, parameters of welding heat source are changed linearly. Based on this study, it is expected that it will be possible to estimate the shape of the heat source under untested welding conditions.

Laser welding is used in various industries due to fast welding speed, and prediction with FEM is needed to design. The multi-layered heat source model that can cover various models has been recently proposed to analyze laser welding, but it takes a lot of time because more than 2,000 cases are compared to derive the results. In order to reduce the time, the simplified model should be suggested. In order to derive a simplified model, laser welding heat transfer analysis was performed using the welding direction length and the convection coefficient of the welding direction surface as parameters. As a result, the model whose difference is less than 0.1% compared to reference model is deducted. The analysis time was reduced by about 90% from 48 hours to 5 hours. Also difference of convection coefficient on the welding direction surface does not affect the temperature distribution much.

As laser welding has low thermal distortion and fast welding speed, the needs in the field is increasing in varous industries. Prediction of distortion and design with that prediction are very important for using welding process in the field. However many types of heat source models for laser welding are suggested, field engineers feels difffucult for using a proper model for a specific case. Thus I, author, suggested a representative model which can cover most of existing models with multi-layered heat source model. This method is very powerful, but there are much time consumption with analysis and comparision among more than 1,000 candidates. To solve these shortcomings, this study focused on to find the simplified model. In order to construct the simplified model, the length of the orthogonal direction to the welding direction was reduced from 300mm to 35mm, which makes time reduction of 75% with sustaining the quality of the original model. That can cover the disadvantage of multi-layered heat source model for laser welding, enhance the prediction of welding distortion after laser welding

PURPOSES : Steel deck bridges are the preferred structural type for reducing dead load, and the use of thin-layer asphalt concrete with excellent adhesion to the steel deck and excellent deformation followability is increasing for bridge pavements. However, because these materials are constructed at a high temperature of 240 °C or higher to maintain high fluidity during construction, excessive thermal deformation and stress may be temporarily induced in the steel deck. Therefore, the stability of the structure must be assessed by considering the environmental conditions of the site during pavement construction. Herein, a method is presented for estimating the heat source equation, in which conduction and convection effects are removed using temperature measurement data, for modeling U-rib using plate elements. The validity of the study is assessed by deriving the equivalent heat source equation using the temperature data measured from the underside of the steel deck while constructing a 40-mm-thick goose asphalt concrete pavement layer on a 12-mm-thick steel deck. In addition, the practicality is verified by performing heat transfer and thermal stress analyses. METHODS : By comparing the temperature data measured during the construction of high-fluidity asphalt concrete with the results of repeated heat transfer numerical analysis, heat source data without field conduction and convection conditions are obtained. Subsequently, a heat source equation suitable for the heat source data is derived using the least-squares method. RESULTS : The results of the heat transfer analysis using the equivalent heat source equation calculated using the presented method are almost consistent with the measured temperature data. In addition, the behavioral characteristics of the structure that matches the behavior of the actual structure can be derived through thermal stress analysis, which considers heat conduction and convection to adjacent members. CONCLUSIONS : Even when the steel deck and U-rib member are modeled as plate elements, thermal effect analysis can be performed reasonably while considering field conditions.

Due to environmental pollution, regulations on existing petroleum-based fuels are increasing day by day. LNG is in the spotlight as an eco-friendly fuel that does not emit NOx or SOx, but its boiling point is -163°C, so it needs to be handled with care. Materials that can be used at the above temperature are defined by IMO through the IGC Code. Among them, 9% nickel steel has great advantages in yield strength and tensile strength under cryogenic conditions, but it is difficult to use in arc welding such as FCAW for various reasons. This study is a study to apply fiber laser welding to solve this problem. As a previous study, this study conducted a study to find a welding heat source. After performing bead on plate welding, the optimal heat source was derived by analyzing the shape of the bead and adjusting the parameters of the heat source model. In this case, by applying the multi-island genetic algorithm, which is a global optimization algorithm, not the intuition of the researcher, accurate results could be derived in a wide range.

The multi-layered heat source model is a model that can cover most of existing studies and can be defined with a simple formula. Based on the methodology performed in previous studies, the welding heat source was found through experiments and FEM under the welding power conditions of three cases and the parameters of the welding heat source were analyzed according to the welding power. In this study, parameters of fiber laser welding heat source according to welding power were searched through optimization algorithm and finite element analysis, and the correlation was analyzed. It was confirmed that the concentration of the welding heat source in the 1st layer was high regardless of the welding power, and it was confirmed that the concentration of the welding heat source in the 5th layer (last layer) increased as the welding power increased. This reflects the shape of the weld bead that appears during actual fiber laser welding, and it was confirmed that this study represents the actual phenomenon.

In this study, a welding heat source model was presented and verified during fiber laser welding. The multi-layered heat source model is a model that can cover most of existing studies and can be defined with a simple formula. It consists of a total of 12 parameters, and an optimization algorithm was used to find them. As optimization algorithms, adaptive simulated annealing, multi island genetic algorithm, and Hooke-Jeeves technique were applied for comparative analysis. The parameters were found by comparing the temperature distribution when the STS304L was bead on plate welding and the temperature distribution derived through finite element analysis, and all three models were able to derive a model with similar trends. However, there was a deviation between parameters, which was attributed to the many variables. It is expected that a more clear welding heat source model can be derived in subsequent studies by giving a guide to the relational expression and range between variables and increasing the temperature measurement point, which is the target value.

Welding is the most widely used technology for manufacturing in the automobile, and shipbuilding industries. Fiber laser welding is rapidly introduced into the field to minimize welding distortion and fast welding speed. Although it is advantageous to use finite element analysis to predict welding distortion and find optimized welding conditions, there are various heat source model for fiber laser welding. In this study, a welding heat source was proposed using a multi-layered heat source model that encompasses most of the existing various welding heat source models: conical shape, curved model, exponential model, conical-cylindrical model, and conical-conical model. A case study was performed through finite element analysis using the radius of each layer and the ratio of heat energy of the layer as variables, and the variables were found by comparing them with the actual experimental results. For case study, by applying Adaptive simulated annealing, one of the global optimization algorithms, we were able to find the heat source model more efficiently.

The estimation of heat source model is very important for heat transfer analysis with finite element method. Part I of this study used adaptive simulated annealing which is one of the global optimization algorithm for anticipating the parameters of the Goldak model. Although the analysis with 3D model which depicted the real situation produced the correct answer, that took too much time with moving heat source model based on Fortran and Abaqus. This research suggests the procedure which can reduce time with maintaining quality of analysis. The lead time with 2D model is reduced by 90% comparing that of 3D model, the temperature distribution is similar to each other. That is based on the saturation of heat transfer among the direction of heat source movement. Adaptive simulated annealing with 2D model can be used to estimate more proper heat source model and which could enhance to reduce the resources and time for experiments.

Anticipation of welding deformation with finite element method is a very interested topic in the industries, adequate heat source model is essential for concluding reasonable results. This study is related to estimate the parameters of Goldak heat source model, and global optimization algorithm is applied to this research. The heat affected zone (HAZ) boundary line of bead on plate (BOP) welding is used as the target, parameters of heat sources are used as the variables. Adaptive simulated annealing is applied and the optimal result is obtained out of 1,000 candidates. The convergence of finite element method and the global optimization is meaningful for estimation of welding deformation, which could enhance to reduce the resources and time for experiments.

In order to enhance the utilization of underground heat including underground water, the comparison between the existing high density polyethylene underground heat exchanger and the newly developed metal heat exchanger was conducted to suggest the potential use of geothermal energy corresponding to the geological characteristics of Jeju Island. When the acquired heat of the underground loop system test condition of the KS B 8292 water-water geothermal heat pump unit was compared by installing heat exchanger of HDPE material and the heat exchanger of STS material under the same bore hole condition, the total heat area of the heat exchanger of STS material was about 15% less than HDPE, but the acquired heat was estimated to be about 4 times or more.

In this study, the cooling and heating amount, temperature, flow rate of turbine type heat meter for water source heat-pump system were experimentally investigated at the standard operating conditions. The obtained cooling and heating capacity from the heat meter were deviated within 5.0%, 3.8% comparing with the precise values calculated from an accredited test facility. Even though the accumulated cooling and heating amount values of the heat meter had a small difference comparing with the precise values, the temperatures of heat meter showed greatly different values comparing with the precise temperature. Therefore, it is highly recommended to develop the heat meter which is appropriate for the water source heat pump systems.

쓰레기 소각장이나 산업체의 폐열을 농업에 활용한 사례는 몇몇 있었다. 그러나 온배수를 농업에 활용한 사례는 전무하였으며, 치어, 종패 등을 양식하는 수산업이 대부분이었다. 본 연구에서는 화력발전소의 온배수(폐열)를 열원으로 이용하는 120 RT 규모의 냉난방시스템을 제주특별자치도 서귀포시 안덕면 소재의 5,280m2 아열대 작물(망고) 재배 온실에 설치, 10월에서 다음해 2월까지 약 5개월 동안 난방을 실시하여 난방에너지 비용 절감 효과 등 분석하였다. 난방에너지 비용 절감효과는 면세경유에 대하여 87%이였으며, 또한 발전소의 온배수를 에너지원으로 재활용함으로 서 62%의 이산화탄소 배출 저감 효과를 얻었다. 본 연구를 계기로 2015년에 해수가 수열에너지 분야로 재생에너지에 포함되었다. 해수의 표층의 열을 히트펌프를 사용하여 변환시켜 얻은 에너지라는 수열에너지 분야의 기준과 범위를 볼 때, 이는 온배수가 재생에너지에 포함되었다고 말해도 과언이 아닐 것으로 사료된다. 그 이유는 온배수도 해수임에도 불구하고 온도가 일반 해수 보다 7~8oC 높아, 일반 해수를 히트펌프의 열원으로 이용하는 것보다 온배수를 열원으로 이용했을 때 히트펌프의 성능이 높기 때문이다. 또한 같은 해 농식품부의 폐열 재이용 시설 지원 사업이 발표되어, 발전소 온배수뿐만 아니라 산업체와 소각장의 폐열을 농업에 활용하면 지원을 받을 수 있게 되었다. 이 사업에 의하여 2015년 당진시, 하동군, 제주시, 곡성군이 선정되었으며, 2016년 태안군, 서귀포시 등이 선정되어, 2016년 말 곡성군과 제주시가 공사를 완료, 농업에 폐열을 활용하고 있으며(제주시는 발전소, 곡성군은 산업체 폐열을 이용하고 있음), 기타 지역은 추진 중이다.