This study presents code-compliant seismic details by addressing dry mechanical splices for precast concrete (PC) beam-column connections in the ACI 318-19 code. To this end, critical observations of previous test results on precast beam-column connection specimens with the proposed seismic detail are briefly reported in this study, along with a typical reinforced concrete (RC) monolithic connection. On this basis, nonlinear dynamic models were developed to verify seismic responses of the PC emulative moment-resisting frame systems. As the current design code allows only the emulative design approach, this study aims at identifying the seismic performances of PC moment frame systems depending on their emulative levels, for which two extreme cases were intentionally chosen as the non-emulative (unbonded self-centering with marginal energy dissipation) and fully-emulative connection details. Their corresponding hysteresis models were set by using commercial finite element analysis software. According to the current seismic design provisions, a typical five-story building was designed as a target PC building. Subsequently, nonlinear dynamic time history analyses were performed with seven ground motions to investigate the impact of emulation level or hysteresis models (i.e., energy dissipation performance) on system responses between the emulative and non-emulative PC moment frames. The analytical results showed that both the base shear and story drift ratio were substantially reduced in the emulative system compared to that of the non-emulative one, and it indicates the importance of the code-compliant (i.e., emulative) connection details on the seismic performance of the precast building.

The ductility of the system based on the capacity of each structural member constituting the seismic force-resisting system is a significant factor determining the structure’s seismic performance. This study aims to provide a procedure to supplement the current seismic design criteria to secure the system’s ductility and improve the seismic performance of the steel ordinary moment frames. For the study, a nonlinear analysis was performed on the 9- and 15-story model buildings, and the formation of collapse mechanisms and damage distribution for dynamic loads were analyzed. As a result of analyzing the nonlinear response and damage distribution of the steel ordinary moment frame, local collapse due to the concentration of structural damage was observed in the case where the influence of the higher mode was dominant. In this study, a procedure to improve the seismic performance and avoid inferior dynamic response was proposed by limiting the strength ratio of the column. The proposed procedure effectively improved the seismic performance of steel ordinary moment frames by reducing the probability of local collapse.

For fast-built and safe precast concrete (PC) construction, the dry mechanical splicing method is a critical technique that enables a self-sustaining system (SSS) during construction with no temporary support and minimizes onsite jobs. However, due to limited experimental evidence, traditional wet splicing methods are still dominantly adopted in the domestic precast industry. For PC beam-column connections, the current design code requires achieving emulative connection performances and corresponding structural integrity to be comparable with typical reinforced concrete (RC) systems with monolithic connections. To this end, this study conducted the standard material tests on mechanical splices to check their satisfactory performance as the Type 2 mechanical splice specified in the ACI 318 code. Two PC beam-column connection specimens with dry mechanical splices and an RC control specimen as the special moment frame were subsequently fabricated and tested under lateral reversed cyclic loadings. Test results showed that the seismic performances of all the PC specimens were fully comparable to the RC specimen in terms of strength, stiffness, energy dissipation, drift capacity, and failure mode, and their hysteresis responses showed a mitigated pinching effect compared to the control RC specimen. The seismic performances of the PC and RC specimens were evaluated quantitatively based on the ACI 374 report, and it appeared that all the test specimens fully satisfied the seismic performance criteria as a code-compliant special moment frame system.

선박 및 교량 구조물은 일종의 길이가 긴 박스형 구조로서 수직 굽힘 모멘트에 대한 저항력이 설계의 주요 인자이다. 특히 선박 거더는 반복적으로 불규칙적인 파랑하중에 장시간 노출되어 있기 때문에 구조부재의 연속 붕괴 거동을 정확하게 예측하는 것이 무엇보다 도 중요하다. 본 논문에서는 순수 휨모멘트를 받는 박스거더의 하중 변화에 따른 좌굴을 포함한 소성 붕괴 거동을 수치해석적 방법을 이용 하여 분석하였다. 분석대상은 Gordo 실험에서 사용한 세 가지 박스거더로 선정하였다. 구조강도 실험 결과와 비선형 유한요소해석에 의한 결과를 비교하여 차이가 발생하는 원인에 대해서 고찰하였다. 본 논문에서는 카본스틸 재료의 제작 시 필연적으로 사용하는 용접열에 의한 초기 처짐의 영향을 반영하기 위하여 전체와 국부적인 처짐 형상의 조합을 제안하였고, 이 결과는 실험 결과와 거동 및 최종강도 추정율이 7% 이내에서 잘 일치하고 있었다. 논문에서 검토한 절차 및 초기 처짐 구성에 대한 내용은 향후 유사 구조물의 최종강도를 분석하는데 좋 은 지침으로 사용할 수 있다.

본 연구는 모형선박의 횡방향 무게분포를 변화시키면서 횡요주기 및 관성모멘트에 의한 GM을 추정하고 경사시험으로 계측되 는 GM 값과 비교한다. 그 과정에서 각 수치를 분석하여 관계성을 파악한다. 실험 및 비교에 사용된 선박의 종류는 3종류로 7톤급, 20톤급 어선과 KVLCC의 모형선을 사용하였다. 실험은 스윙프레임 테스트와 자유 횡요 감쇠테스트를 수행하여 관성모멘트와 횡요주기를 계측하 고, 경사시험으로 GM을 계측하였다. 관성모멘트와 횡요주기로 추정된 GM과 경사시험으로 구해진 GM은 선박의 무게 분포 변화에도 동 일한 경향을 보였지만, 경사시험에서 구해진 GM이 더 작은 값을 보였다. 따라서 GM 추정 시에 관성모멘트나 횡요주기 외에도 추가적인 보정 계수나 파라미터가 필요하다고 판단된다. 추후 무게중심을 변화시켜 추정 GM과의 관계를 분석하여 보정 계수를 산출할 계획이다.

This study presents a dry precast concrete (PC) beam-column connection, and its target seismic performance level is set to be emulative to the reinforced concrete (RC) intermediate moment resisting frame system specified in ACI 318 and ASCE 7. The key features include self-sustaining ability during construction with the dry mechanical splicing method, enabling emulative connection performances and better constructability. Test specimens with code-compliant seismic details were fabricated and tested under reversed cyclic loading, which included a PC beam-column connection specimen with dry connections and an RC control specimen. The test results showed that all the specimens failed in a similar failure mode due to plastic deformations in beam members, while the hysteretic response curve of the PC specimen showed comparable and emulative performances compared to the RC specimen. Seismic performance evaluation was quantitatively addressed, and on this basis, it confirmed that the presented system can fully satisfy all the required performance for the intermediate RC moment resisting frame.

국내의 서비스 수준 지진(SLE)과 최대 고려 지진(MCE)의 두 RC 건물 구조물의 실험 및 해석 결과에서 얻은 탄성 및 비탄성 응답은 비틀림에 대한 전단 및 비틀림 거동에서 저항 메커니즘의 특성을 연구하는데 사용될 수 있다. 불균형 구조의 특성 연구에서는 전단력 및 비틀림 모멘트에 대한 병진 변형 및 비틀림 변형의 상호 작용 효과를 나타내는 방정식이 제안하였다. 탄성과 비탄성 거동에서 힘과 변형 사이에 상관 관계 유무가 다르기 때문에 증분 전단력과 증분 비틀림 모멘트를 최대 벽 프레임 변형을 중심으로 항복, 제하 및 재 하중 단계로 구분하여 해당 증분 변형 및 증분 비틀림 변형 측면에서 해석을 수행하였다. 두 가지 주요 지배 모드의 탄성 조합에서 병 진 변형은 주로 전단력에 기여하는 반면 비틀림 변형은 전체 비틀림 모멘트에 크게 기여한다. 그러나 비탄성 응답에서는 증분 병진 변 형이 증분 전단력과 증분 비틀림 모멘트 모두에 기여하게 된다. 따라서 주어진 방정식을 이용하여 비탄성 응답에서 비틀림의 편심 감 소, 비틀림 강성 저하 및 겉보기 에너지 생성과 같은 모든 현상들을 설명하였다.

New buildings have been designed using different seismic design standards that have been revised. However, the seismic performance of existing buildings is evaluated through the same performance evaluation guidelines. Existing buildings may not satisfy the performance targets suggested in the current guidelines, but there are practical limitations to discriminating the existing buildings with poor seismic performance through a full investigation. In this regard, to classify buildings with poor seismic performance according to the applied standard, this study aimed to evaluate performance-based investigation of the seismic design proposals of buildings with different design standards. The target buildings were set as RC ordinary moment frames for office occupancy. Changes in seismic design criteria by period were analyzed, and the design spectrum changes of reinforced concrete ordinary moment resisting frames were compared to analyze the seismic load acting on the building during design. The seismic design plan was derived through structural analysis of the target model, compared the member force and cross-sectional performance, and a preliminary evaluation of the seismic performance was performed to analyze the performance level through DCR. As a result of the seismic performance analysis through the derived design, the reinforced concrete ordinary moment frame design based on AIK 2000 has an insufficient seismic performance level, so buildings built before 2005 are likely to need seismic reinforcement.

현 설계기준에서 제시한 단부횡보강 상세는 시공성과 생산품질이 현저히 떨어지므로 내진성능과 시공성을 확보할 수 있는 RC 구 조벽체의 단부횡보강 상세 개발이 필요하다. 최근 선재 제작기술의 발전으로 다양한 선조립철근의 제작이 가능해지고 있으며 특히 다양한 연속횡보강 철근 상세의 제작이 가능하게 되었다. 본 연구에서는 사각 연속횡보강 선조립철근 단부횡보강 상세를 적용한 RC 구조벽체의 모멘트-곡률 관계에 대한 분석을 진행하였다. 비선형 단면해석에 의하면 사각 연속횡보강의 상세를 적용한 RC 구조벽체 는 사각 연속횡보강 영역의 면적이 증가할수록 내진성능을 확보할 수 있다. 이러한 연구결과에 근거하여 사각 연속횡보강 선조립 철 근의 상세 적용시, 단부횡보강 영역의 면적만큼 사각 연속횡보강 영역의 면적을 확보해야 한다.

The design of the corner joints in furniture structures is very important to firmly support the loaded structure and to sufficiently maintain the durability and stability. Therefore, the strength of the corner joints and the rigidity of the connected panels play a very important role in the structural performance of the assembled furniture. The structural properties can be measured or calculated experimentally or numerically, and compared by representing the applyed forces or bending moments as a function of deformed value. This paper shows the numerical models to determine the strength and stiffness of the 3-types of corner joints for simple designed furniture. Based on the finite element results, the maximum stresses are concentrated on the corner joints designed with MDF panels. And the deformation resistances and maximum applied loads are calculated for furniture corner joints under tensile and compressive moment.

본 논문은 임동식(1945~, 충남 연기군)의 작품 세계를 분석하고 퍼포먼스 지속 대안으로 살펴보는 시도다. 2020년 서울시립미술관 개인전과 박수근미술상 수상 등으로 주목받았지만 그에 관한 심도 깊은 연구는 부재하기에 의미가 있다. 기존의 연구는 그가 관계한 ‘야투: 야외현장미술 연구회’ 또는 ≪예술과 마을≫ 프로젝트의 일부로 그쳤다. 임동식의 작품 세계는 “자연 현장 기반 퍼포먼스”와 그것을 기록한 아카이브, 그려낸 회화로 구성되어 독자적 모습을 보여준다. 연구는 작가가 한국과 독일을 오가며 이 같은 작품 세계를 구축한 배경을 한국 실험 미술의 태동과 전개의 맥락에서 우선 조사한다. 이어서 작가가 함부르크 조형예술대학 학위 시험에서 자기 사유를 대표하는 작품으로 소개한 1985년 퍼포먼스 <거북이와 함께한 방랑>, <풀잎과 마주한 생각>과 거기서 비롯한 아카이브, 회화를 중심으로 작업 구조를 파악한다. 그 과정에서 할 포스터(Hal Forster)의 「아카이브적 충동(An Archival Impulse)」(2004), 더글라스 크림프(Douglas Crimp)의 「픽쳐스(Pictures)」(1979)를 읽어 아카이브의 예술적 가능성을 파악하는 동시에 퍼 포먼스와 회화 사이 괴리를 좁히며 그것을 타블로 비방으로 규정한다. 결론적으로 임동식의 퍼포먼스, 아카이브, 타블로 비방이 각각 다른 차원에서 하나의 자아를 구성하며 한국 실험 미술의 성과인 이 독자성이 최근 활발한 퍼포먼스 지속 연구의 대안 제시로 의미가 있다고 밝힌다.

In seismic design standards such as KDS 41 17 00 and ASCE 7, three procedures are provided to estimate seismic demands: equivalent lateral force (ELF), response spectrum analysis (RSA), and response history analysis (RHA). In this study, two steel special moment frames (SMFs) were designed with ELF and RSA, which have been commonly used in engineering practice. The collapse probabilities of the SMFs were evaluated according to FEMA P695 methodology. It was observed that collapse probabilities varied significantly in accordance with analysis procedures. SMFs designed with RSA (RSA-SMFs) had a higher probability of collapse than SMFs designed with ELF (ELFSMFs). Furthermore, RSA-SMFs did not satisfy the target collapse probability specified in ASCE 7-16 whereas ELF-SMFs met the target probability.

This paper is to investigate the retrofitting effect for a non-seismic reinforced concrete frame strengthened by perimeter steel moment frames with indirect integrity, which ameliorates the problems of the direct integrity method. To achieve this, first, full-scale tests were conducted to address the structural behavior of a two-story non-seismic reinforced concrete frame and a strengthened frame. The non-seismic frame showed a maximum strength of 185 kN because the flexural-shear failure at the bottom end of columns on the first floor was governed, and shear cracks were concentrated at the beam-column joints on the second floor. The strengthened frame possessed a maximum strength of 338 kN, which is more than 1.8 times that of the non-seismic specimen. A considerable decrease in the quantity of cracks for the strengthened frame was observed compared with the non-seismic frame, while there was the obvious appearance of the failure pattern due to the shear crack. The lateral-resisting capacity for the non-seismic bare frame and the strengthened frame may be determined per the specified shear strength of the reinforced columns in accordance with the distance to a critical section. The effective depth of the column may be referred to as the longitudinal length from the border between the column and the foundation. The lateral-resisting capacity for the non-seismic bare frame and the strengthened frame may be reasonably determined per the specified shear strength of the reinforced columns in accordance with the distance to a critical section. The effective depth of the column may be referred to as the longitudinal length from the border between the column and the foundation. The proposed method had an error of about 2.2% for the non-seismic details and about 4.4% for the strengthened frame based on the closed results versus the experimental results.

FRP 시트(Sheet)를 활용한 보강 공법은 제작 과정에서의 간편함과 시공의 용이성으로 현장에서 다수 적용되고 있으며, 기존 연구자들은 FRP 시트로 보강한 철근콘크리트의 휨강도를 예측하기 위한 연구를 진행하였다. 그러나 이는 주로 탄소 섬유와 유리 섬유에 한정되어 있었다. 이 연구에서는 바잘트 섬유시트의 역학적 성질을 파악하기 위하여 물성 시험을 수행하였으며, 바잘트 섬유시트로 보강한 철근콘크리트 보의 휨실험을 수행하였다. 또한 그 결과 값을 비교 분석하여 기존 연구를 바탕 으로 바잘트 섬유 시트로 보강한 철근콘크리트 보의 휨모멘트 예측식을 제안하였다. 강도설계법, ACI440.2R (2017) 그리고 Park et al. (2005)의 예측값을 검토한 결과, 강도설계법은 실험값과 예측값의 비가 0.88로 나타났으며, ACI440.2R (2017) 설계식은 0.92, Park et al. (2005)은 0.97로 나타나 기존의 해석 방법은 휨모멘트를 과대평가하는 것으로 나타났다. 본 연구의 제안식은 실험값과 예측값의 비가 1.00으로 나타나 휨모멘트를 안전측으로 예측하는 것으로 나타났다.

The purpose of this study was to assess knee joint loading in the target knee during a golf swing compared to loading rates of high impact activities such as cutting and drop landings. Nine healthy competitive golfers completed golf swings with the target foot both straight and externally rotated 30 degrees, as well as drop landings and cutting maneuvers. Motion capture data was collected at 240 Hz and ground reaction force data was collected at 2400 Hz. The frontal and transverse knee moments were examined using repeated measures ANOVA through SPSS. The abduction moments were higher in golf swings as compared to the other high impact activities (p=.010), while the external rotation moments were lower (p=.003). There were no significant differences between externally rotated and neutral golf swings. These results suggest moments applied to the knee during a golf swing are similar to those applied during a high impact activity.

Lightly reinforced concrete (RC) moment frames may suffer significant damage during large earthquake events. Most buildings with RC moment frames were designed without considering seismic loads. The load-displacement response of gravity load designed frames could be altered by masonry infill walls. The objective of this study is to investigate the load-displacement response of gravity load designed frames with masonry infill walls. For this purpose, three-story gravity load designed frames with masonry infill walls were considered. The masonry infilled RC frames demonstrated larger lateral strength and stiffness than bare RC frames, whereas their drift capacity was less than that of bare frames. A specimen with a partial-height infill wall showed the least drift capacity and energy dissipation capacity. This specimen failed in shear, whereas other specimens experienced a relatively ductile failure mode (flexure-shear failure).