PURPOSES: The purpose of this study is to verity the applicability of a portable small-loop electromagnetic survey method to underground cavity detection. METHODS: In order to evaluate applicability of the method, a test bed comprised of four sections was constructed. The two sizes of the four cavities artificially formed at two depths were contained in the test bed. Each cavity was positioned at center of each 6 m long section. Four types of pavement materials such as unpaved ground, bricks, asphalt, and concrete were used at every section. The portable small-loop electromagnetic device measured electrical conductivity as an exploration signal that varied according to the electrical properties underground. The electrical conductivity was converted into two-dimensional electrical resistivity distribution sections using an inverse analysis program. RESULTS : The results showed that the electrical resistivity of the non-cavity area was lower than that of the cavity area. The electrical resistivity increased as the measurement device moved closer to the cavity position. It was also found that the electrical resistivity values were not significantly affected by pavement type. The small cavity with diameter of 35 cm could be detected up to 1.2 m depth. CONCLUSIONS: Therefore, it was verified that the portable small-loop electromagnetic survey method is applicable to the detection of cavities in sections where ground subsidence is expected. This method can be effectively used for small-scale roads such as sidewalks, parkways, and side streets where large exploration equipment cannot enter.

In general, the pretensioned PSC members are manufactured at the factory and are transported to the site. Due to road conditions, their sizes are limited. Therefore, until now pretensioning method is only applied to small PSC members. In order to produce large scale PSC members using pretensioning method, they shall be made on site. In this study, a portable prestressing device to produce pretensioning PSC girders on site has been developed. The portable prestressing device should be safe and stable about jacking force. In this paper, the portable prestressing device to produce 10m-span pretensioning PSC girders was made. The static loading test was performed to analyze the resisting mechanism of each component of that device. The jacking force was introduced by stretching and anchoring the tendons at its both ends. In the static loading test, the structural characteristics of the developed device are investigated.

Both a fluorescent marking system (FMS) and a portable harmonic radar system (PHRS) are effective insect tracking methods. Prior to comparing their efficacies, we tested the viability of FMS in detection of an agricultural pest, Riptortus pedestris (Hemiptera: Alydidae); previous studies showed the harmlessness of PHRS on R. pedestris and its detection distance. Fluorescent marking allowed the detection of marked R. pedestris from > 25 m, when illuminated with a laser in the dark, while affecting only the vertical walking distance of the insect. Then, we assessed the efficacy of the FMS and PHRS as well as combining both methods (BOTH) in detection of R. pedestris in a grass field and a bean field during day and night. PHRS and BOTH showed higher detection rates than FMS in all settings, except for in the bean field at night. Also, although BOTH did not enhance total detection time, it facilitated the retrieval of the sample at night compared to only using PHRS.

Many studies for personal mobility are increasing at the latest. One part of personal mobility study is electric scooter. Driving elements of electric scooter are battery and motor, patterns of vehicle being proposed multiply by manufacturer. The old and the infirm's population in domestic and abroad increases day by day. Thus, the personal vehicle for them that can be managed easily is needed for them. Following the trend “personal mobility”, this study propose electric-drive scooter which is portable and compact. Prototypes of proposed models are manufactured to commercialize it. As results, adopt of foldable type at electric scooter can be decreased size. Also 4-wheel scooter is more stable than 3-wheel sooter.

This study developed a portable extinguishing equipment that can extinguish A-class, B-class fire. This equipment is made of Water Mist Gun, controlling board, decelerator, pump, engine, and etc,. This equipment is formed mist water when pressurized water with high pressure flows through a radial shape nozzle. As a result of several efficiency tests, it is developed nozzle and equipment that are not clogged, and improved the extinguishing efficiency. This developed equipment indicated a excellent effect of initial extinguishment of fire in a vulnerable area where it is difficult to approach such as temple, and traditional market.

When a radiation detector is applied to the measurement of the radioactivity of high-level of radioactive materials or the rapid response to the nuclear accident, several collimators with the different inner radii should be prepared according to the level of dose rate. This makes the in-situ measurement impractical, because of the heavy weight of the collimator. In this study, an IRIS collimator was developed so as to have a function of controlling the inner radius, with the same method used in optical camera, to vary the attenuation ratio of radiation. The shutter was made to have the double tungsten layers with different phase angles to prevent the radiation from penetrating owing to the mechanical tolerance. The performance evaluation through the MCNP code was conducted by calculating the attenuation ratio according to the inner radius of the collimator. The attenuation ratio was marked on the outer scale ring of the collimator. It is expected that when a radiation detector with the IRIS collimator is used for the in-situ measurement, it can change the attenuation ratio of the incident photon to the detector without replacing the collimator.

The goal of this research was to develop a portable system that could be used to evaluate the quality of milk in real time at a raw milk production site. A real-time portable quality evaluation system for raw milk was developed to enable non-destructive quality evaluation of somatic cell count (SCC), fat, protein, lactose, and total solid (TS) in milk samples. A prediction model of SCC, fat, protein, lactose, and TS was constructed using partial least squares (PLS) and 200 milk samples were used to evaluate the prediction performance of the portable quality evaluation system and high performance spectroscopy. Through prediction model development and verification, it was found that the accuracy of high performance spectroscopy was 90% for SSC, 96% for fat, 96% for protein, 91% for lactose, and 97% for TS. In comparison, the accuracy of the portable quality evaluation system was relatively low, at 90% for SSC, 95% for fat, 92% for protein, 89% for lactose, 92% for TS. However, the measurement time for high performance spectroscopy was 10 minutes for 1 sample, while for the portable quality evaluation system it was 6 minutes. This means that the high performance spectroscopy system can measure 48 samples per day (8 hours), while the portable quality evaluation system can measure 80 (8 hours). Therefore, it was found that the portable qual ity evaluation system enables quick on-site quality evaluation of milk samples.

The objectives of this study were to evaluate the safe criteria of portable slipmeter using human perception onto the several different floor surfaces under contaminated conditions. It was difficult to find why many different slipmeters took there’s own safe criteria. It is still unclear how thres hold values established in many literatures. Two different subjective slippery evaluating methods, AHP(Analytic Hierarchy Process) and Friedman test,were used to evaluate the perception of slipperiness of seven different floor surfaces under the contaminated condition with detergent solution. Twelve subjects worn same footwear and walked with self-selected step and cadence along the test floors. The SCOF(Static Coefficient of Friction) obtained for same test conditions with BOT-3000 was compared to perception of slipperiness to establish as a safe criteria. The very high significant correlation(r=0.97) was found between AHP and Friedman test. Also, The high significant correlation(r=0.96) was found between AHP and SCOF obtained with BOT-3000. The results suggested that the SCOF should be greater than 0.63 for safer walking. Perception rating obtained with AHP showed a high correlation with Friedman test and the SCOF obtained with BOT-3000 except for polished tile floor.The safe criteria obtained through this study were similar to ANSI/NFSIB101.1.

목 적: 시각손상을 유발하였을 시, 광학 확대경과 휴대용 전자확대경을 사용시 근거리 사물을 인식하는데 걸리는 시간에 대해서 평가하고자 한다. 방 법: 15명의 참여자에게 영수증 내에 있는 여러 가지 정보와 사진의 정보를 파악하는데 걸리는 시간을 측정하였다. 3가지 시각 손상 조건을 구현하였으며, 이는 시력저하, 백내장 그리고 시야협착이었다. 이런 시각 손상 조건하에서 광학확대경과 전자확대경에 대한 사물인식 시간을 측정하였다. 결 과: 본 연구에 참여한 참여자는 21세부터 26세로 평균나이는 22.73±1.28이다 근거리 정보를 인식과 사진의 정보를 파악하는데 걸린 시간은 광학확대경과 휴대용 확대경간 유의한 차이가 없었다. 시각 손상 조건을 서로 비교하였을 때, 시력저하 조건과 백내장 조건은 유의한 차이가 없었으나, 시력저하와 시야협착 그리고 백내장 조건과 시야협착 조건간에는 유의한 차이를 보였다. 결 론: 근거리 사물의 정보를 인식하는데 있어서, 광학 확대경과 휴대용 전자확대경은 비슷한 정도의 효율성을 보여주었다. 하지만 시야협착이 있는 경우에는 다른 시야 손상에 비해 정보인식 시간이 다소 오래 걸렸다. 따라서, 시야협착이 있는 경우에는 시야 확장에 도움이 되는 보조기기의 처방을 통하여, 읽기 능력 향상을 도와주는것을 고려하여야 할 것이다.

PURPOSES : Skid resistance and noise of roads highly depend on the characteristics of pavement texture. Therefore, estimation of texture characteristics may give useful information for the skid resistance and noise of road. Generally, Sand Patch Test is performed in order to estimate MTD(Mean Texture Depth). However, it is time-consuming and needs traffic control. This study aimed to investigate the effectiveness of measurement texture depth using the Portable Laser Profiler that give the MPD(Mean Profile Depth). METHODS : MTD and MPD were collected on the number of expressway sections including Central Inland Test Road sections in Korea. Statistical analysis are performed to establish the relationship between MTD data based on Sand Patch Test and MPD data obtained by the Portable Laser Profiler. RESULTS : Linear relationship MPD and MTD is observed for both of asphalt pavement and concrete pavement such as R-square of 0.51 to 0.58. CONCLUSIONS : Even though, the test method and definition of MPD and MTD are different. EMTD(Estimated Mean Texture Depth) can be obtained by using the correlationship between MPD with MTD.

Marine caused pollution occurs mostly near coastal area and its main cause was known to be human feces issued from small vessels. To sterilize liquid pollutants from portable toilets of small vessels, an electrolysis treatment is judged to be the most economic and stable method considering an environment of its use. In this paper, we presents an electrolysis apparatus which is the most appropriate for sterilizing pollutants from portable toilets of small vessels and derives the minimum operating time of the apparatus for sterilizing norovirus which is a main target of marine caused pollution sources. In order to utilize renewable energy, we designed an apparatus which generates a renewable energy from solar cells. As a result, we could confirm the applicability of the proposed system with the results from experiments in three cases of different weather conditions.

본 연구는 최근 조사료의 신속한 품질평가 방법으로 근적외선 분광법의 이용성이 확대되고 있는 시점에 근적외선 분광기의 현장 적용성을 평가하기 위하여 수행되었다. 실험실용 근적외선분광기와 소형 근적외선분광기의 조사료 품질평가의 예측 정확성을 평가하기 위하여 전남지역에서 이탈리안 라이그라스 사일리지 67점을 수집하여 각각의 근적외선 분광기를 이용하여 스펙트럼을 측정한 후 사료가치의 실험실 분석값과 다변량회귀분석을 통하여 검량식을 유도하여 예측 정확성을 평가하

본 연구에서는 국내의 시설 내 작물재배에 적합한 자동관수 기술을 개발하기 위한 첫 단계로 전기저항의 변화원리를 이용하는 워터마크 센서를 장착한 소형 컨트롤러를 작물재배에 활용하여 자동관수기술의 효용성을 구명하고자 하였다. 이를 위해 비닐하우스 내에 다른 토성을 갖는 토양을 격리베드에 인공적으로 조성한 후 토마토를 정식하여 수분퍼텐셜을 -20kPa 수준으로 자동으로 조절하면서 재배하였다. 점적관수에 따른 토양 내 깊이별 수분변화는 Sentek 축전형 수분센서를 이용하여 측정하였다. 워터마크센서를 이용한 수분퍼텐셜 제어성능은 (-)20kPa 수준부근에서 유지되지 않고 반복적으로 0~(-)20kPa 대역에서 높은 변화 값을 나타내어 안정적이지 못한 것으로 나타났다. 특히, 물 공급은 관수시마다 약 50~60분 비교적 긴 시간동안 진행되어 수분공급이 과잉되는 문제가 나타났으며 건조시에도 수분퍼텐셜의 변화가 계단응답 반응의 형태로 변하는 불량한 측정해상도를 나타내었다. 이러한 문제는 워터마크센서의 토양과 전극 접촉형태가 다공컵식 수분장력계에 비해 수분값에 연속적으로 반응할 수 없는 구조이기 때문인 것으로 판단하였다. 자동관수에 따른 토양종류별 수분변화는 그 기울기가 토성별로 서로 달랐으며 양질사토의 경우 수분함량의 변화정도가 가장 높았다. 수분함량의 변화속도는 낮과 밤의 경우 시간에 따른 변화율이 달라서 변곡선의 형태를 나타내었다. 이러한 이유는 낮과 밤의 일교차와 태양광 유무에 의하여 수분증발량 차이가 발생하였기 때문인 것으로 판단하였다. 직물에서 20cm 떨어진 지점의 깊이별 수분함량은 작물에 인접한 위치와 비교하였을 때 세가지 토양 모두 관수에 의한 변화정도는 미미하여 직물에 인접한 곳만 수분공급이 효율적으로 이루어지는 것을 확인하였다. 추후 연구에서 양질사토 베드에서 관찰된 토마토 생육 불량 문제 개선과 관수멈춤 시간을 적용하여 물공급의 과잉 문제를 해결하는 보완실험이 요구되었다.

최근 10년간 전세계적으로 아스팔트 포장을 재활용하는 기술이 급속도로 확산되고 있으며 노후 아스팔트 포장을 폼드 아스팔트 또는 유화 아스팔트를 사용하여 현장에서 바로 100% 재활용하는 현장 상온 재생 아스팔트 포장기술이 다양하게 적용되고 있다. 특히, 아이오와 주에서는 교통량이 적은 지방도로에서 기존 포장의 수명을 연장 시켜주는 현장 상온 재생 아스팔트 공법을 많이 적용하고 있다. 일반적으로 현장 상온 재생 아스팔트 포장층은 수분의 침투나 교통하중으로부터 보호하거나 포장설계를 만족시키기 위해 가열 아스팔트 포장으로 덧씌우기를 한다. 일반적으로 현장 상온 재생 아스팔트 포장층 위에 가열 아스팔트 포장으로 덧씌우기 할 시기는 대부분에 감독자들은 일정한 양생기간 또는 최대 함수비에 근거하여 결정하고 있다. 따라서, 본 연구에서는 감독자가 최적에 덧씌우기 아스팔트 포장 시기를 결정할 수 있도록 현장 상온 재생 아스팔트 포장층의 현장 함수비를 간단하게 측정하여 덧씌우기 시기를 결정할 수 있는 수분 감소계수를 개발하는 것이다. 먼저, 현장 상온 재생 아스팔트 포장층의 함수비를 TDR 함수량계를 사용하여 측정하였고 현장 상온 재생 아스팔트 포장이 시공되는 기간 동안에 강우량, 대기온도, 습도, 바람속도 등 기상정보를 수집하였다. 마지막으로 현장 상온 재생 아스팔트 포장의 초기 함수비, 대기온도, 습도, 바람속도를 변수로 하는 수분 감소계수를 개발하였다. 실제 현장 상온 재생 아스팔트 포장에서 측정한 값을 사용하여 개발한 수분 감소계수는 감독자가 연속적으로 현장 상온 재생 아스팔트 포장층의 함수비를 측정하지 않고 최적의 덧씌우기 포장 시점을 결정할 수 있다.

Pine wilt disease, caused by pine wood nematode, Bursaphelenchus xylophilus (Steiner et Buhrer) Nickle, has become the most serious threat to pine trees in Korea since first reported in 1988. Pine wood nematode is transferred to uninfested trees by Monochamus alternatus (Coleoptera: Cerambycidae) (vector). A typical controlling method against vectors in Korea is fumigation of the dead trees infested by vector M.alternatus and B.xylophilus using metam-sodium SL(25%). However, this method is harmful to the environment because of the chemical contamination and vinyl waste in the mountain afterward. Portable Bark Remover (PBR) was contrived to reduce these environmental problems. The vectors oviposite under the bark of the freshly dead trees only. Debark infested trees prohibited the vectors from oviposite and finally, vectors can not complete their life cycle. The PBR is a newly designed as a debarking device that is equipped on top of the chain saw engine allowing ease and rapid debarking of the infested trees at the controlling field. Debarking of freshly-dead trees can eliminate egg-laying and hatch places where between the wood and bark from vectors. The new method for vector controlling using the debarking device is expected to lower-price and high-efficiency comparing with other conventional methods such as “crushing”, “burning” and “fumigation”.