In this study, a tuned mass damper(TMD) was installed to control the displacement response to earthquakes by generalizing to six analysis models according to the shape of the upper structure based on the case of various large spatial structures around the world. The six analysis models are ribbed type, latticed type, elliptical type, gable type, barrel type, and stadium type composed of 3D arch trusses. In this paper, ribbed type, latticed type and elliptical type were analyzed. The mass of each TMD was set to 1% of the total structural mass. Result of analyzing the optimal number and position of the analysis model, the displacement response control was the most excellent in the model with 6 and 8 TMDs, and the displacement response decreased in most cases. The displacement response control was better with installing the TMD at the edge point than focusing the TMD at the center of the analysis model. However, when 10 or more TMDs are installed or concentrated in the center, large loads intensively act on the structure, resulting in increased displacement. Therefore, although it is slightly different depending on the shape, it is judged that the displacement response control is the best to install 6 and 8 TMDs at the close to the edge point.

In this study, performance experiments were performed on the shape of steel dampers that affect the rocking behavior. Three types of strut shapes of SI type, SV type and SS type were considered as experimental variables. As a result of the experiment, the capacity to resist the moment and drift ratio according to the strut shape of the steel damper was evaluated as very close. Finally, it was evaluated that the SV type steel damper has stable deformation and energy dissipation capability. As a result of the evaluation of the proposed damper transmission force, it is considered that the damper transmission force is evaluated larger than the applied horizontal force, and it is necessary to supplement it.

Many electronic applications require magnetic materials with high permeability and frequency properties. We improve the magnetic permeability of soft magnetic powder by controlling the shape magnetic anisotropy of the powders and through the preparation of amorphous nanoparticles. For this purpose, the effect of the shape magnetic anisotropy of amorphous Fe-B-P nanoparticles is observed through a magnetic field and the frequency characteristics and permeability of these amorphous nanoparticles are observed. These characteristics are investigated by analyzing the composition of particles, crystal structure, microstructure, magnetic properties, and permeability of particles. The composition, crystal structure, and microstructure of the particles are analyzed using inductively coupled plasma optical emission spectrometry, X-ray diffraction, scanning electron microscopy and focused ion beam analysis. The saturation magnetization and permeability are measured using a vibrating sample magnetometer and an LCR meter, respectively. It is confirmed that the shape magnetic anisotropy of the particles influences the permeability. Finally, the permeability and frequency characteristics of the amorphous Fe-B-P nanoparticles are improved.

Due to the serious air pollution problem, interest in eco-friendly vehicles is increasing. Solving the problem of pollution will necessitate the securing of high energy storage technology for batteries, the driving force of eco-friendly vehicles. The reason for the continuing interest in the transition metal oxide LiMO2 as a cathode material with a layered structure is that lithium ions reveal high mobility in two-dimensional space. Therefore, it is important to investigate the effective intercalation and deintercalation pathways of Li+, which affect battery capacity, to understand the internal structure of the cathode particle and its effect on the electrochemical performance. In this study, for the cathode material, high nickel Ni0.8Co0.1Mn0.1(OH)2 precursor is synthesized by controlling the ammonia concentration. Thereafter, the shape of the primary particles of the precursor is investigated through SEM analysis; X-ray diffraction analysis is also performed. The electrochemical properties of LiNi0.8Co0.1Mn0.1O2 are evaluated after heat treatment.

This study utilized data to classify and characterize the body types of plus-size adult men aged in their 30s and 40s. Diversity is an important factor in the era of inclusive design, and discussion about size diversity to include the plus size should be accommodated. Data from 493 adult men classified as obese (with a World Health Organization criterion ≥25 BMI) were used for the analysis. The results of the study are as follows. Six independent factors were extracted using factor analysis for cluster analysis, which were then classified into five types. Type 1 (29.01%) was identified as body type I with the smallest degree of obesity. Type 2 (15.4%) was identified as body type Y with wide shoulders and a thin waist. Type 3 (14.2%) was the largest body volume (body type O), while the fourth (19.27%) identified as body type H has a large height and upper body. Lastly, type 5 (22.11%) has a long lower body and a slim abdomen, referred to as body type X. This study presents a basis for the development of various clothing sizes utilizing the body shape characteristics of plus-size men in their 30s and 40s. Follow-up research is needed to develop patterns for plus size men and to design various products.

In this study, the structural analyses were conducted for each model by applying the loads into the design of a large commercial truck seat. Model C with three vertical frames has the smallest total deformation among all models, indicating the strongest stiffness. The maximum total deformation of model C was shown to be 0.68 times smaller than that of model A and 0.79 times smaller than that of model B. The equivalent stress of model C was also shown to be the lowest, indicating the greatest stiffness. The maximum equivalent stress of model C was shown to be 0.8 times smaller than that of model A and 0.91 times smaller than that of model B. At the upper part of the seat or the part where the force was applied, all three models were shown to have the largest total deformations and equivalent stresses. If the result of this study is applied to the design of automotive seat frame, it is thought that the durable and rigid sheets can be manufactured efficiently. By utilizing this study result, the equivalent stress and total deformation are investigated without the real experiment by shape at the seat of large commercial truck, and the durability and rigidity can be seen.

Hydro-electric power is a method of generating electricity from the rotational force of turbine blades by using the potential energy of a river or reservoir water. Recently, the necessity of small hydropower development is expanding due to the development and support of renewable energy, and because of the difficulty and environmental problems of huge dams. The purpose of this paper is to deal with a method of increasing the efficiency of small water turbine that can be adopt in low head condition. In order to improve the turbine efficiency, channel shape is optimized in order to minimize head loss using computational fluid dynamics. The angle values for the contraction and enlargement part of the channel where the turbine is located are found from the analyses. Additionally, three-dimensional analysis is applied to the optimized channel shape in order to confirm the optimized pipe.

Natural gas is the most realistic fuel among eco-friendly fuels. Natural gas production is limited, and in Korea, it is supplied and utilized in the form of liquefied natural gas (LNG). In the case of LNG, the vaporization point is 163 degrees below zero, so ordinary metal cannot be used due to its brittleness. The International Maritime Organization (IMO) defines metals that can be used in the IGC Code, and is used for storage containers, transportation containers, etc. based on the metals. Welding is essential in the manufacture of large structures such as LNG storage tanks. In this study, weldability studies related to cryogenic materials were conducted. In Part I of this study, high-manganese steel and part II were studied for two types of stainless steel (STS304L, STS316L), and in Part III, aluminum (AL5083). During laser welding, the shape of the Bead on Plate (BOP) was analyzed, and a total of nine cases were analyzed using laser power and welding speed as variables. It was confirmed that the penetration and the width of the welding width were linearly proportional to the amount of heat input. Based on this study, it is possible to conduct a follow-up study to find the optimal welding conditions for butt welding and fillet welding.

As the part of efforts to respond to the environmental pollution, the demand for clean energy is increasing. Natural gas is one of the most realistic alternatives, and interest in the storage and transportation containers to utilize the natural gas is growing. The production area of ​​natural gas is limited, and in Korea, it is imported in the form of liquefied natural gas. LNG is a cryogenic state with a vaporization point of -163°C, so the ordinary metal cannot be used due to its brittleness. The international maritime organization (IMO) defines the metals that can handle LNG in the IGC Code, and the research is ongoing. This study was a preliminary study to check the weldability of related metals and confirmed the shape of bead on plate (BOP) during the laser welding for each material. In part I, a study was conducted on the high manganese steel, and in part II, a study was conducted on the materials of STS304L and STS316L among the stainless steel. Based on this study, it can be used as an optimal welding condition for the butt and fillet welding.

In this study, the flow analyses were carried out on the electric train models with three kinds of mounting materials installed at the front part of train. By examining the results of flow rate and pressure, It was investigated which type of design should be designed to be more efficient in high-speed operation. The three types of models are set as models a, b and c, and each has its own shape. For all models, the wind speed was set at 110 km/h, the most common driving speed for wide-area electric trains. In the case of the model a, it was good at cutting the wind flow as a round shape when viewed from the top. But from the side, it showed a vortex forming in the upper corner. To the contrary, the model b, which has a wedge-shaped side, could be seen from the top as a result of a vortex. Finally, in the case of model c combined with models a and b, the least vortex, front pressure, and resistance forces were shown by selecting the flow advantages of models a and b. By utilizing this study result, the flow velocity and pressure are investigated without flow experiment by shape of the front part of electric train, and the flow capacity can be seen.

As demand for eco-friendly energy increases, demand for natural gas and Liquefied natural gas (LNG) storage technologies continues to increase. LNG is a cryogenic environment with a temperature of -163°C, so ordinary metals cannot be used due to brittleness. Accordingly, IGC Code designates the cryogenic materials such as Invar, STS304L, Al5083-0, and High Manganese Steel. For fabricating those materials, research on welding possibility is the most important. Thus this study focused on the possibility of laser welding of the cryogenic materials. The weldability of High Manganese Steel was researched in this paper, the shape and the dimensions of the beads after bead on plate (BOP) welding were observed. The experiment was conducted on a total of 25 cases with laser power and welding speed of 5 cases each, and the width, height, and penetration of the beads were confirmed. It was confirmed that the paramenter of bead increased linearly with the laser power, and the paramenters of bead increased linearly with decreasing welding speed. Based on this study, high manganese steel can be applied in various industries by applying it to butt welding.

In this study, by analyzing the flow rate and the pressure applied to the fan for the flow of air with room temperature into the fan in desktop computer, it was investigated which model was suitable for flow resistance. When comparing the speed distribution of air flow by model according to fan shape, model A was able to confirm that the fan performance was not good but the external flow was widely distributed. And model B was able to know that the performance was good but the external flow was smaller. Model C was found to have good performance and a wide distribution of outer flow. In cases of three models, it was equally shown that the pressure was highest on the blade side of the inlet where the air enters. Model B receives more pressure than models A and C when the same air flow rate is applied, so models A and C are considered more efficient cooling fans than model B. When considering the flow rates and the pressures acting on the model, model C is thought to have relatively good performance. By utilizing this study result, the flow rate and pressure are investigated without flow experiment by the shape of fan in desktop computer, and the flow capacity can be seen.

In this study, the deformation, equivalent stress and strain energy were analyzed on the electric kick board emerging as a new means of transportation at the accident of a front collision according to each shape were analyzed. The largest part deformation happened at the handle, and the board part where the person’s feet was placed was seen to become weak. The equivalent stress was most visible at the board section, unlike the deformation results. In particular, the deformation and stress of model A which has a long and thin neck, have occurred greatly. Therefore, the longer the neck, the greater the deformation and stress occur. Among all models, the deformation and stress were the smallest at model C. As model A has a particularly thinner neck and board connection part, a large strain energy appeared. Therefore, it is considered that the connection needs to be reinforced thickly and firmly. On the study result, the thicker the board part of the electric kick board and the lower the body of the vehicle, the safer it is. The results of this study can be effectively applied to investigate the values of stresses and deformations, and strain energies through structural analysis without the fracture test at the front collision according to the shape of electric kick board.

In this study, the structural and fatigue analyses were carried out according to the shape of the self-made car frame. As a result of structural analysis, all models are shown to have the weak strength and large deformation, as the equivalent stress increases at the forward part of the impact force. It can be seen that model 3 is deformed less than other models 1 or 2. And model 3 with the truss structure prevents the great deformation from the collision. In case of irregular fatigue loads, the fatigue life of the ‘Sample history’ increased by about 59.3 times compared to the ‘SAE bracket history’ under extreme fatigue load conditions, indicating that the fatigue load condition of the ‘Sample history’ were stable. The fatigue life and deformation of model 3 among all models are significantly different to models 1 and 2. If the research results are applied to the design of self-made cars, it will be useful for improving the durability and preventing the damage. The results of this study can be effectively utilized to investigate the values of stresses and deformations, and fatigue lives without the experiments of fracture and fatigue according to the shape of the car frame.