Several tests should be performed to estimate the structural and chemical stability of the radioactive waste. Among the tests in Gyeongju LILW repository, the leaching test which follows ANS 16.1 standard test method should be conducted for Cs, Sr, and Co radionuclides and must satisfy leachability index larger than 6 which applies deionized water as a leachant. However, the expected leachant inside the silo is groundwater that contains various ions and a high pH condition is predicted due to the concrete structures inside the silo. According to the chemical environment of the leachant, the chemical form of the radionuclides varies from precipitate to ion. Cobalt precipitates when the leachant has high pH environment which is similar condition to the cement-saturated leachant. Unlike the cobalt, cesium is preferred to exist as ion in the high pH condition. Therefore, the significant effect of the chemical environment of the leachant on the leachability of the radionuclides should be considered for the waste acceptance criteria of the radioactive waste repository. From the ‘NRC, Technical position on the waste form, rev1’, the leaching test method should follow the ANS 16.1 methods by using deionized water as leachant, however, a new leachant showing more aggressive leachability can be applied instead of deionized water. In the other hand, ASTM C1308 leaching test method recommends applying actual groundwater of the repository as a leachant. FT-04-020, the leaching test method of France, suggests the ion composition of the groundwater including the pH value. Therefore, the adequacy of using deionized water as leachant for the leaching test method of Cs, Sr, and Co should be re-examined. In this study, the leaching behavior of Cs, Sr, and Co under the several leachant types is estimated. The cement solidified specimen containing single Cs, Sr, and Co were manufactured. The leaching test following ANS 16.1 was performed by applying deionized water, simulated groundater, and cement-saturated groundwater. As a result, a leachability index difference according to the leachant type was discussed. The result of this study is expected to be a background data that helps understanding the actual leaching behavior of the Cs, Sr, and Co in the Gyeongju LILW repository.

In this paper, uniaxial tensile tests of ETFE films with three kinds of thicknesses(100, 200, 250μm) and two kinds of directions(machine direction & transverse direction) are performed and the tensile strength, the tensile strain at break and the Young’s modulus of ETFE films are compared for two kinds of specimen types(2 & 5). It could be figured out that there are no significant difference between tensile strengths of two specimen types but the tensile strain at break and the Young’s modulus of ETFE films are affected by the specimen types. And it is concluded that the uniaxial tensile test of specimen type 2 are more reliable than that of specimen type 5.

Three-dimensional motion analysis systems and force plates are used for gait phase detection and ground reaction force(GRF) or ground reaction moment(GRM) data collection. But force plates as measurement systems are restricted to laboratory environments and have limitations for abnormal walking with foot dragging. Therefore the methods were proposed to compute the GRM from the kinematic data of three-dimensional motion analysis systems. Gait phase detection with kinematic data using foot velocity algorithm(FVA) was performed. The validity of gait phase detection was obtained comparing with the results of force plates. A gait model with 7 segments was composed to compute GRM. The results of gait model with kinematic data were compared with those of force plates. The result of the vertical direction is similar. But anterior-posterior direction and lateral direction show similar tendency with some gaps.

Nowadays, the study of CFRP reinforced with carbon fiber is focused on improving the the mechanical property. The study on the fracture data of CFRP are not properly made out than that of the general mechanical joint. In this study, the fracture property of mode 1 at the same condition of tensile experiment is investigated by applying the layer angle to laminated CFRP with the thickness of 15 mm. When the reaction forces until dropping out the bonded surface are compared with the cases of the layer angles of 0°, 45° and 60°, the reaction force is shown to be most and the elapsed time until dropping out the bonded surface is longest at that of 45°. The deformation energy is also shown to have the highest value by dropping out the adhesive interface. As the basis of the analysis result of this study, the most safety with fracture resistance is shown in the case of 45°. the bonded structure applying the appropriate layer angle is thought to have the structural safety.

CFRP has the high strength and low weight. But it tends to be frail if it is applied with the mechanical bonding method using weld, rivet or bolt. So, the chemical bonding method using the special adhesive has been utilized. By applying the bonding method with the adhesive, this paper investigates the mechanical property of DCB specimen bonded with the type of mode 2 through the simulation analysis. Four kinds of specimen thicknesses are 25mm, 35mm, 45mm and 55mm in this study. The mechanical behaviors of specimens due to the forced displacements are investigated as the distributions of equivalent stresses. The reaction force becomes higher as the specimen thickness is increased. The result of this study about the fracture property of adhesive joint is thought to be contributed to the safe design of structure with CFRP.

As aluminum foam has the most superior absorption of impact energy, this material has been used at automobile and airplane. If aluminum foam is used by jointing bolt and nut, it can be broken. Therefore, it is more effective to bond aluminum foam and other materials by adhesive. In this study, the fatigue fracture simulation through ANSYS program is carried out on the aluminum foam specimen bonded with adhesive as the type of DCB Mode Ⅲ. There are four kinds of specimens with the types of DCB Mode Ⅲ in this study. The thicknesses of four specimens are 35mm, 45mm, 55mm and 65mm. In cases of specimen thicknesses of 35mm, 45mm, 55mm and 65mm, the maximum loads are shown as ±0.2kN, ±0.55kN, ±1kN and ±1.2kN respectively. As the specimen thickness increases, the maximum loads increase. The results of fatigue experiment as specimen thickness of 55mm can be shown to approach the simulation results by confirming the simulation results of this study. So, The simulation data can be applied in order to investigate the mechanical property at DCB specimen with the type of Mode Ⅲ.

현미경을 이용한 관찰기술은 나날이 발전하고 있으며 그 중에서도 공초점현미경은 최근 여러 분야에서 응용연구가 진행되고 있다. 본 연구에서는 파장이 632.8nm인 He-Ne 레이저를 사용하고, NA=1.25이며 배율이 100x인 대물렌즈와 3차원 스테이지를 사용하여 시료 이동방식(specimen scanning)의 공초점 현미경을 구성하였다. 그리고 PMT(photo multiplier tube)를 통하여 CD(compact disc)의 표면 형상에 대한 정보를 얻어 Labview 프로그램으로 3차원 입체영상을 구현하였다. 그 결과 피트 간격이 1.7µm, 피트의 깊이 0.1µm인 것으로 측정되어 문헌 값과 거의 일치함을 확인하였다.

구조실험에서 정확성과 효율성을 높이기 위해서는 적절한 실험장치를 적용하는 것은 중요한 요소이다. 특히, 대규모의 구조실험에서 적절한 실험장치는 비용과 시간을 절감할 수 있다. 액츄에이터와 유압잭 및 UTM은 실험체의 휨 능력을 평가하는 데일반적으로 적용되고 있다. 그러나, 대규모 실험체에서 다점 다하중 가력하중이 적용되어야 하는 경우에는 기존의 UTM 등을이용하는 실험방법은 정확한 하중을 가력하기에 어려움이 많다. 이를 해결하기 위하여 본 연구에서는 실험결과의 정확성과 효율성을 높이기 위하여 기존의 실험장치로 조합된 새로운 방법을 개발하였다.