본 연구에서는 상용화된 로프절단장치 타입 중 국내에 가장 많이 도입되어있는 Scissor type을 대상으로 유한요소해석을 수행하여 다양한 로프 걸림 상황에서 안정성이 확보되는 적합한 구조 형태를 평가하였으며, 수조 실험 및 실선 실험을 통해 효용성을 검증하였다. 연구 결과, 로프 걸림에 의하여 프로펠러축이 회전하지 않을 경우 엔진에서 발생하는 지속적인 토크로 인하여 로프절단장치에 비틀림이 발생하고 유한요소 해석상 자유도가 구속되어 있지 않은 하부의 블레이드에서 가장 높은 변형이 발생하는 것을 확인하였다. 블레이드의 두께가 증가할수록 최대변형량은 줄어들고 최대응력은 낮아져 안전율이 증가하는 결과가 나타났으며, 동일한 블레이드 두께에서 토크의 변화량이 최대응력과 최대변형량에 미치는 영향은 로프절단장치의 외력이 미치는 위치와 무관하며 정비례하게 감소하는 것으로 나타났다. 해석 결과를 토대로 실시한 수조실험 및 실선실험 결과, 모든 조건과 환경에서 로프 및 어망이 원활하게 제거되는 것을 확인하였다.

With respect to spent nuclear fuels, disposal containers and bentonite buffer blocks in deep geological disposal systems are the primary engineered barrier elements that are required to isolate radioactive toxicity for a long period of time and delay the leakage of radio nuclides such that they do not affect human and natural environments. Therefore, the thermal stability of the bentonite buffer and structural integrity of the disposal container are essential factors for maintaining the safety of a deep geological disposal system. The most important requirement in the design of such a system involves ensuring that the temperature of the buffer does not exceed 100℃ because of the decay heat emitted from high-level wastes loaded in the disposal container. In addition, the disposal containers should maintain structural integrity under loads, such as hydraulic pressure, at an underground depth of 500 m and swelling pressure of the bentonite buffer. In this study, we analyzed the thermal stability and structural integrity in a deep geological disposal environment of the improved deep geological disposal systems for domestic light-water and heavy-water reactor types of spent nuclear fuels, which were considered to be subject to direct disposal. The results of the thermal stability and structural integrity assessments indicated that the improved disposal systems for each type of spent nuclear fuel satisfied the temperature limit requirement (< 100℃) of the disposal system, and the disposal containers were observed to maintain their integrity with a safety ratio of 2.0 or higher in the environment of deep disposal.

The pipe for water supply is essential part among SOC (Social Overhead Capital) fields. Pipe for water supply is mainly damaged by deterioration of pipe, earthquake, ground sinking and so on. The leakage of water have been led to enormous economical loss in our country. The purpose of this study was to investigate the structural stability of flexible joint for relaxing impact due to earthquake and ground sinking. For this purpose, flexible joint was simulated using tensile load and internal pressure. As the results, flexible joint for structural stability was needed the tensile load of below 3 ton and internal pressure of below 60 kgf/cm2. However, it is considered that real flexible joint should be applied more high safety factor than that of simulation result because of combined stress.

Recently, automobile washing methods have been carried out using steam of high temperature and high pressure instead of water. Therefore, it is necessary to secure the structural stability of the steam tank. In this study, it is necessary to reduce the weight of the steam tank by reducing the thickness of the existing steam tank by about 25%. The safety of the product design was verified through simulation to ensure the robustness of the product by securing the structural stability and fatigue analysis at high temperature and pressure of the steam tank according to the weight reduction. For newly developed products compared to existing models.

In this paper, dynamic model of 120mm self-propelled mortar is developed, and multi flexible body dynamics analysis is performed to analyze stresses occurring in the mount during mortar fire. For this, vehicle dynamic system, mortar dynamic system, and finite element mount model are proposed. The commercial program Recurdyn is used in the analysis. As a result of the analysis, the maximum stress(146.9MPa) occurred at the mount side plate. In order to analyze the validity of the analysis results, we performed strain measurement tests by selecting three major points, and the errors of results were 7.91%, 11.15%, and 18.23%, respectively. It is confirmed that the tendency of analysis and test is similar.

SUS hexagonal bar has been widely used to make many kinds of hexagonal bolt/nuts and fittings. Peeling machine is used to make lustrous and clean surface of SUS circular bar in order to remove rust and impurities from surface of raw SUS circular bar. Similarly, roll unit system is used to make SUS hexagonal bar from SUS circular bar with lustrous and clean surface. Roll unit system is mainly divided into two parts ; one is roll unit and the other is mold frame. The purpose of this study was to evaluate the structural stability of mold frame supporting roll unit with numerical analysis. As the numerical analysis result, higher structural stability was gradually shown in order of models 4, 2, 3 and 1. It was considered that the structural stability of this study was influenced by the decrease of mold frame size, especially height decrease.

In recent years, single layer latticed domes have attracted many designers and researchers’s attention all over the world, because single layer latticed domes as space structure are of great advantage in not only mechanical rationality but also function, fabrication, construction and economic aspect. Yamada developed the shape factor S which represents the shape of spherical latticed dome from a structural perspective as well as a geometric perspective. According to a prior study, the structural behavior and the buckling characteristics of the latticed dome were mostly noticeable when the shape factor of latticed dome was in the range of 1.5 to 5. That is, S, in the range of 1.5 to 5, are able to estimate not only overall buckling, but also member buckling and nodal buckling. In this study, we developed shape models using various size of members with the fixed rise-span ratio. One particular characteristic of the latticed dome is that it is not only light in weight but also high in strength. But the aiming at the use of light-weight materials and at the minimized section of members may result in buckling to cause an unstable state of the overall structure when the external force reaches a limitation. Especially, the structural strength is disadvantageous to the snow loads than the earthquake loads because of light-weight, and is greatly affected by the conditions of loading. This paper is to develop the structural stability according to the shapes and load conditions for single-layer latticed spherical dome with 300m span.

본 연구에서는 간척지에서 플라스틱 온실의 기초안전성을 평가하기 위하여 강재 나선말뚝기초를 갖는 폭 6m 연동하우스 1개동과 강재 나선말뚝기초와 파이프줄기초를 각각 적용한 폭 8.2m 단동하우스 2개동을 SPT N값 이 2인 간척지 시험포장에 설치하여 플라스틱 온실의 인발량 및 침하량을 측정하였다. 또한 플라스틱 온실에 적용된 나선말뚝기초 3종(φ50, φ75 및 φ100)을 인근의 간척지 시험포장에 설치하여 인발저항특성을 시험하였다. 평가 기간 중 플라스틱 온실의 수직변위 움직임이 관측 되었지만 온실의 규모와 비교하여 그 변위는 무시할만한 수준이었다. 평가 기간 중의 최대 수직변위는 나선말뚝 기초를 적용한 연동하우스의 경우 +9.0mm(인발)~- 11.5mm(침하), 나선말뚝기초를 적용한 단동하우스의 경 우 +1.3mm~-7.7mm, 파이프줄기초를 적용한 단동하우스 의 경우 +0.9mm~-11.2mm로 나타났다. 나선말뚝기초의 허용인발력은 모두 극한하중 판정기준에 의해 판단할 수 있었으며 φ50mm, φ75와 φ100 나선말뚝기초의 최종 허용인발력은 각각 0.40kN, 1.0kN과 2.5kN으로 산정할 수 있었다. 평가기간 중 나선말뚝기초를 적용한 플라스틱 온실의 기초안전성을 최종적으로 판단하기에는 다소 무리가 있다고 판단되나 강재 나선말뚝기초를 간척지 플라스틱 온실의 기초로 사용하더라도 큰 문제는 없을 것으로 판단되었다.

In recent years, single layer latticed domes have attracted many designers and researchers's attention all over the world, because single layer latticed domes as space structure are of great advantage in not only mechanical rationality but also function, fabrication, construction and economic aspect. One of the most important factor, in building of single-layer single-layer lattice spherical dome with 300m span, is to ensure the structural safety. Network pattern of single layer latticed domes can be infinitely taken into account. The typical network patterns are triangle, square, hexagon etc. Especially triangular network pattern has mechanically more advantage than the other network patterns because of having not only a large equivalent shearing rigidity but also a large equivalent bending rigidity and axial rigidity. Among the triangular network pattern, that is, 3 way grid pattern, there are many mechanical differences according to the arranging methods of members. In order to ensure the structural stability of single-layer latticed dome with 3 way grid, designers are required to maintain a constant member length and the member angle. In order to achieve this, it is important to search the member array that the standard deviation of the member lengths and angles is the smallest. This paper is to develop the arrangement of member and to verify its validity for single-layer latticed spherical dome with 300m span.