PURPOSES : The purpose of this study is to provide basic data to improve the service life of asphalt pavement using basalt aggregate in Jeju Island by evaluating the performance of asphalt pavement through analysis of material and structural aspects. METHODS : To evaluate the performance of Jeju Island's asphalt pavement, cracks, permanent deformation, and longitudinal roughness were analyzed for the Aejo-ro road, which has high traffic and frequent premature damage. Cores were collected from Aejo-ro sections in good condition and damaged condition, and the physical properties of each layer were compared and analyzed. In addition, plate cores were collected from two sections with severe damage and the cause of pavement damage was analyzed in detail. RESULTS : About 45% of the collected cores suffered damage such as layer separation and damage to the lower layer. The asphalt content of surface layer in the damaged section was found to be 1.1% lower on average than that in the good condition section, and the mix gradations generally satisfied the standards. The density difference between the cores of each layer was found to be quite large, and the air voids was found to be at a high level. CONCLUSIONS : Test results on the cores showed that, considering the high absorption ratio of basalt aggregate, the asphalt content was generally low, and the high air voids of the pavement was believed to have had a significant impact on damage. High air voids in asphalt pavement can be caused by poor mixture itself, poor construction management, or a combination of the two factors. Additionally, the separation of each layer is believed to be the cause of premature failure of asphalt pavement.

In this study, we developed Rapid Enrichment Broth for Vibrio parahaemolyticus (REB-V), a broth capable enriching V. parahaemolyticus from 100 CFU/mL to 106 CFU/mL within 6 hours, which greatly facilitates the rapid detection of V. parahaemolyticus. Using a modified Gompertz model and response surface methodology, we optimized supplement sources to rapidly enrich V. parahaemolyticus. The addition of 0.003 g/10 mL of D-(+)- mannose, 0.002 g/10 mL of L-valine, and 0.002 g/10 mL of magnesium sulfate to 2% (w/v) NaCl BPW was the most effective combination of V. parahaemolyticus enrichment. Optimal V. parahaemolyticus culture conditions using REB-V were at pH 7.84 and 37oC. To confirm REB-V culture efficiency compared to 2% (w/v) NaCl BPW, we assessed the amount of enrichment achieved in 7 hours in each medium and extracted DNA samples from each culture every hour. Real-time PCR was performed using the extracted DNA to verify the applicability of this REB-V culture method to molecular diagnosis. V. parahaemolyticus was enriched to 5.452±0.151 Log CFU/mL in 2% (w/v) NaCl BPW in 7 hours, while in REB-V, it reached 7.831±0.323 Log CFU/mL. This confirmed that REB-V enriched V. parahaemolyticus to more than 106 CFU/mL within 6 hours. The enrichment rate of REB-V was faster than that of 2% (w/v) NaCl BPW, and the amount of enrichment within the same time was greater than that of 2% (w/v) NaCl BPW, indicating that REB-V exhibits excellent enrichment efficiency.

This study presents a method for analyzing the surface temperatures of specific facilities, such as the 5 MWe reactor within the Yongbyon Nuclear Complex, to explore its potential utility in monitoring suspected nuclear-related activities in North Korea using thermal infrared (TIR) satellite imagery (Landsat series). TIR band data is utilized to derive surface temperatures in the specified areas, and the temperatures are analyzed on a monthly basis to examine any patterns within these regions. This research provides a pattern-of-life on temperature variation for the target areas through multiple TIR image datasets, offering additional information to analyze facilities’ operational status in remote and inaccessible regions.

Injection molding is a process of shaping resin materials by heating them to a temperature above their melting point and then using a mold. The resin material is injected into and cooled within the mold cavity, solidifying into the desired shape. The core and cavity components that make up the mold cavity are crucial elements for the precision molding in injection molding. In the case of precision mold production, the application of 5-axis machining technology is required to ensure high machining quality for complex shapes, and among these factors, the tool angle is a critical machining condition that determines the surface roughness of the workpiece. In this study, we aim to measure the surface roughness of the machined surface of KP4A specimens during machining processes with variations in the tool angle and analyze the correlation between the tool angle and surface roughness.

Western coastal area of Chungnam, including Cheonsu Bay and Garorim Bay, has suffered from hot and cold extremes. In this study, the extreme sea surface temperature on the western coast of Chungnam was analyzed using the quantile regression method, which extracts the linear regression values in all quantiles. The regional MOHID (MOdelo HIDrodinâmico) model, with a high resolution on a 1/60o grid, was constructed to reproduce the extreme sea surface temperature. For future prediction, the SSP5-8.5 scenario data of the CMIP6 model were used to simulate sea surface temperature variability. Results showed that the extreme sea surface temperature of Cheonsu Bay in August 2017 was successfully simulated, and this extreme sea surface temperature had a significant negative correlation with the Pacific decadal variability index. As a result of future climate prediction, it was found that an average of 2.9oC increased during the simulation period of 86 years in the Chungnam west coast and there was a seasonal difference (3.2oC in summer, 2.4oC in winter). These seasonal differences indicate an increase in the annual temperature range, suggesting that extreme events may occur more frequently in the future.

수도권에 위치한 S매립장 내 3개의 매립장을 대상으로 매립가스 배출 및 주요 경로별 표면 발산과 관련된 분석을 하였다. 전체 매립가스 발생비율 10.9%인 LS1이 총 표면발산 비중은 49.4%를 차지하고 있었다. 3개 매립장에서의 메탄의 총 표면발산은 13.6 Nm3/min로서, LS1 8.4 Nm3/min (61.7%), LS2 4.0 Nm3/min(29.4%), LS3 1.2 Nm3/min(8.9%)이고, 발산경로별로는 상부 7.3 Nm3/min (53.2%), 사면 6.4 Nm3/min(46.7%), 다이크 0.02 Nm3/min(0.1%)이었다. 3개 매립장의 주요 배출경로 별 산화율은 다이크가 87.5%로 가장 크고, 상부 72.3%, 사면 71.8% 순이었다. 메탄을 기준으로 표면발 산 기여율은 매립장 별로 LS1이 전체의 61.7%로 가장 컸다. 주요 배출경로별로는 LS1의 사면이 전체의 41.7%, LS2의 상부 24.4%, LS1의 상부 20.0%로서 S매립장의 전체 메탄 표면발산량의 86.1%를 차지함 에 따라 향후 집중적인 관리가 필요할 것으로 판단되었다.

Surface water temperature of a bay (from the south to the north) increases in spring and summer, but decreases in autumn and winter. Due to shallow water depth, freshwater outflow, and weak current, the water temperature in the central to northern part of the bay is greatly affected by the land coast and air temperature, with large fluctuations. Water temperature variations are large in the north-east coast of the bay, but small in the south-west coast. The difference between water temperature and air temperature is greater in winter and in the south-central part of the bay than that in the north to the eastern coast of the bay where sea dykes are located. As the bay goes from south to north, the range of water temperature fluctuation and the phase show increases. When fresh water is released from the sea dike, the surrounding water temperature decreases and then rises, or rises and then falls. The first mode of empirical orthogonal function (EOF) represents seasonal variation of water temperature. The second mode represents the variability of water temperature gradient in east-west and north-south directions of the bay. In the first mode, the maximum and the minimum are shown in autumn and summer, respectively, consistent with seasonal distribution of surface water temperature variance. In the second mode, phases of the coast of Seosan~Boryeong and the east coast of Anmyeon Island are opposite to each other, bordering the center of the deep bay. Periodic fluctuation of the first mode time coefficient dominates in the one-day and half-day cycle. Its daily fluctuation pattern is similar to air temperature variation. Sea conditions and topographical characteristics excluding air temperature are factors contributing to the variation of the second mode time coefficient.

Carbon steel pipes, which are essentially used in the manufacturing industry, are used in various fields due to the advancement of the industry, and a cutting process is essentially applied to pipes manufactured in a nominal size. The cutting process is the most basic and first process used to obtain a material in a desired shape, and it can affect the quality of subsequent processes such as welding or painting, so high-quality cutting surfaces are essential. Therefore, due to the advantage of improving productivity, it is essential to study to secure the appropriate quality of the cutting surface of the plasma cutting process, which is widely used in the industrial field. In this study, the effect of cut surface quality according to process parameters in the plasma cutting process for carbon steel pipe materials was analyzed. The surface roughness was measured to determine the quality of the cut surface, and the relationship between the surface roughness and the process variables was confirmed by selecting the arc current and cutting speed, which are identified as the main factors forming the surface roughness, as process variables.

The most comprehensive and particularly reliable method for non-destructively measuring the residual stress of the surface layer of metals is the sin method. When X-rays were used the relationship of sin measured on the surface layer of the processing metal did not show linearity when the sin method was used. In this case, since the effective penetration depth changes according to the changing direction of the incident X-ray,  becomes a sin function. Since  cannot be used as a constant, the relationship in sin cannot be linear. Therefore, in this paper, the orthogonal function method according to Warren’s diffraction theory and the basic profile of normal distribution were synthesized, and the X-ray diffraction profile was calculated and reviewed when there was a linear strain (stress) gradient on the surface. When there is a strain gradient, the X-ray diffraction profile becomes asymmetric, and as a result, the peak position, the position of half-maximum, and the centroid position show different values. The difference between the peak position and the centroid position appeared more clearly as the strain (stress) gradient became larger, and the basic profile width was smaller. The weighted average strain enables stress analysis when there is a strain (stress) gradient, based on the strain value corresponding to the centroid position of the diffracted X-rays. At the 1/5 max height of X-ray diffraction, the position where the diffracted X-ray is divided into two by drawing a straight line parallel to the background, corresponds approximately to the centroid position.

Recently, halogen lamps for vehicle exterior lamp systems are being replaced by LEDs (Light Emitting Diode) in consideration of miniaturization, power consumption, life, luminance, and eco-friendliness. Due to regulations on the amount of light required, luminance, light uniformity, and glare prevention, it is required to develop a light guide for controlling a light source of an LED lamp for a vehicle. For the development of the light guides, the development of machining technology that can cut micro patterns of hundreds of micrometers scale into surface roughness of tens of nanometers scale must be preceded. In this study, the effect of variations in cutting conditions on surface roughness was analyzed through experiments. The micro patterns was manufactured by cutting into STAVAX material, and the surface of the micro patterns was super-finished using a ball-shaped PCD (polycrystalline diamond) tool without flutes. In experiments, the cutting conditions of the super-finishing process were varied, and the varied cutting conditions were feed rate, radial depth of cut, and spindle speed

대표적인 짚공예 가운데 하나인 맥간공예(혹은 보릿대 조각공예)는 표면이 매끄럽고 광택이 나는 보릿대를 활용하고 있으며 최근에 국내뿐 아니라 해외로 전파되고 있다. 보릿대 표면의 줄기 방향과 나란한 미세 줄무늬는 맥간공예 작품에 입체감과 각도에 따른 색감을 갖게 한다. 하지만 아직까지 보릿대 표면의 형상과 물성이 체계적으로 분석되지 않은 실정이다. 본 연구에서는 고해상도 실체현미경과 고해상도 3차원 X-ray 현미경을 이용하여 보릿대의 미세구조를 이미징할 뿐만 아니라 보릿대의 물접촉각과 인장 강도를 측정하여 보릿대의 재질을 분석하였다. 이를 통해 보릿대 최외각에 존재하는 4-6 μm 너비의 미세요철에 의한 줄무늬, 소수성을 띈 겉면, 친수성을 띈 속면, 그리고 60 MPa 정도의 줄기 방향의 항복강도를 갖는 보릿대 특성을 확인하였다. 본 연구에서 제시한 분석 방법으로 볏짚을 비롯한 다른 짚공예에 사용되는 짚 재료의 특성을 파악한다면 짚의 재질을 최대로 활용한 새로운 짚공예로 이어질 것이다.

The function of coolant in machining is to reduce the frictional force in the contact area in between the tool and the material, and to increase the precision by cooling the work-piece and the tool, to make the machining surface uniform, and to extend the tool life. However, cutting oil is harmful to the human body because it uses chlorine-based extreme pressure additives to cause environmental pollutants. In this study, the effect of cutting temperature and surface roughness of titanium alloy for medical purpose (Ti-6Al-7Nb) in eco-friendly ADL slot shape machining was investigated using the response surface analysis method. As the design of the experiment, three levels of cutting speed, feed rate, and depth of cut were designed and the experiment was conducted using the central composite planning method. The regression expressions of cutting temperature and surface roughness were respectively obtained as quadratic functions to obtain the minimum value and optimal cutting conditions. The values from this formula and the experimental values were compared. As a result, this study makes and establishes the basis to prevent environmental pollution caused by the use of coolant and to replace it with ADL (Aerosol Dry Lubricant) machining that uses a very small amount of vegetable oil with high pressure.

PURPOSES : To efficiently manage pavements, a systematic pavement management system must be established based on regional characteristics. Suppose that the future conditions of a pavement section can be predicted based on data obtained at present. In this case, a more reasonable road maintenance strategy should be established. Hence, a prediction model of the annual surface distress (SD) change for national highway pavements in Gangwon-do, Korea is developed based on influencing factors. METHODS : To develop the model, pavement performance data and influencing factors were obtained. Exploratory data analysis was performed to analyze the data acquired, and the results show that the data were preprocessed. The variables used for model development were selected via correlation analysis, where variables such as surface distress, international roughness index, daily temperature range, and heat wave days were used. Best subset regression was performed, where the candidate model was selected from all possible subsets based on certain criteria. The final model was selected based on an algorithm developed for rational model selection. The sensitivity of the annual SD change was analyzed based on the variables of the final model. RESULTS : The result of the sensitivity analysis shows that the annual SD change is affected by the variables in the following order: surface distress ˃ heat wave days ˃ daily temperature range ˃ international roughness index. CONCLUSIONS : An annual SD change prediction model is developed by considering the present performance, traffic volume, and climatic conditions. The model can facilitate the establishment of a reasonable road maintenance strategy. The prediction accuracy can be improved by obtaining additional data, such as the construction quality, material properties, and pavement thickness.

해상교통분석은 복잡해지는 해양환경에 따라 발생하는 문제해결을 위해 다방면으로 시행되고 있다. 하지만 4차 산업혁명으로 부터 도래된 자율운항선박 개발 등의 해사분야 동향은 해상교통분석에도 변화가 필요함을 암시한다. 이에 해상교통분석의 개선점을 식별 하고자 관련 연구를 분석하였으며, AIS데이터의 활용도가 높은 반면에 해도정보의 활용은 그 중요도에 비해 부족한 것으로 조사되었다. 이에 본 연구는 자율운항선박의 상용화에 대비한 해상교통분석의 개선점으로서 수치해도 데이터와 선박운항데이터인 AIS데이터를 복합 적으로 활용하는 방법을 제시하였다. 연구결과로써 해상교통분석에 수치해도데이터를 활용하였을 때 추출 가능한 해상교통특성을 제시 하였으며 이는 향후 자율운항선박의 도입을 위한 해상교통분석에 활용가능할 것으로 기대된다.

Phosphate coating is applied to the surface of the round bar material used in the multi-stage cold forging process for the purpose of lubrication. The film characteristics are determined according to the conditions of the phosphate film treatment process. In this study, the film properties according to the phosphate treatment conditions were defined as the coefficient of repeated friction and quantitative analysis was performed. Different friction behaviors were exhibited depending on the film properties, suggesting that optimization of the phosphate film treatment conditions is possible based on this. Finally, as a practical example, friction behavior according to the film characteristics was applied to the automotive engine bolt forming process. As a final conclusion, the need for linkage analysis with phosphating conditions for optimizing the forging process was raised. In addition, it can be seen that damage to the phosphate film should be considered in the process of predicting the limiting life of the die.

생체용 마그네슘 합금은 전연성 부족과 열에 의한 팽창률 변화가 심하여 2mm 이하의 판재를 만드는 것이 매우 어려움 문제이다. 이를 해결하기 위해 압연 방식, 세이퍼 방식, 밀링 방식 등의 다양한 방법이 존재할 수 있다. 압연 방식을 적용하여 실험을 진행하였으나 Mg 합금은 전연성, 취성의 문제로 인해 파괴되는 현상이 발생하였다. 그리고 세이퍼 방식은 가공시 충격이 발생하는 단속절삭이기 때문에 표면에 자국이 남게 되고 시험편이 휘어지는 현상이 발생하는 문제가 발생하였다. 최종적으로 밀링 방식으로 전환하여 가공실험을 수행해 본 결과 매우 만족할 만한 결과값을 얻게 되었고, 이 결과는 절삭조건을 절삭회전수 1000rpm, 이송속도 127mm/rev, 절삭깊이 0.5mm로 엔드밀 사용하여 가공하였을 때 Ra = 0.44㎛의 표면거칠기값을 얻게 되었다. 본 논문에서는 생체 마그네슘 합금재료로 미소판재를 가공하였을 때 매우 좋은 표면을 유지하며 2mm 이하의 미소 두께를 지속적으로 가공이 가능하도록 하였으며, 다양한 절삭조건, 2날과 4날 엔드밀 날수 변화 등을 통해 최적의 가공조건을 알아보는 실험을 진행하였다.