The organic binder-free paste for dye-sensitized solar cell (DSSC) has been investigated using peroxo titanium complex. The crystal structure of TiO2 nanoparticles, morphology of TiO2 film and electrical properties are analyzed by X-Ray Diffraction (XRD), Scanning Electron Microscopy (SEM), Electrochemical Impedance Spectra (EIS), and solar simulator. The synthesized TiO2 nanopowders by the peroxo titanium complex at 150, 300, 400˚C, and 450˚C have anatase phase and average crystal sizes are calculated to be 4.2, 13.7, 16.9, and 20.9 nm, respectively. The DSSC prepared by the peroxo titanium complex binder have higher Voc and lower Jsc values than that of the organic binder. It can be attributed to improvement of sintering properties of TCO/TiO2 and TiO2/TiO2 interface and to formation of agglomerate by the nanoparticles. As a result, we have investigated the organic binder-free paste and 3.178% conversion efficiency of the DSSC at 450˚C.

In this study, titanium(Ti) meshes and porous bodies are employed to synthesize carbon nanotubes(CNTs) using methane(CH4) gas and camphene solution, respectively, by chemical vapor deposition. Camphene is impregnated into Ti porous bodies prior to heating in a furnace. Various microscopic and spectroscopic techniques are utilized to analyze CNTs. It is found that CNTs are more densely and homogeneously populated on the camphene impregnated Ti-porous bodies as compared to CNTs synthesized with methane on Ti-porous bodies. It is elucidated that, when synthesized with methane, few CNTs are formed inside of Ti porous bodies due to methane supply limited by internal structures of Ti porous bodies. Ti-meshes and porous bodies are found to be multi-walled with high degree of structural disorders. These CNTs are expected to be utilized as catalyst supports in catalytic filters and purification systems.

The effect of titanium dioxide (TiO2) on the properties of color conversion glasses was examined for glasses based on BaO-ZnO-B2O3-SiO2. One glass sample, containing 25 mol% of each component, was used as a reference; the other three glass samples contained 1, 3, and 5 mol% TiO2, respectively. The four color conversion glass samples were prepared by sintering a mixture of glass frits and a YAG:Ce+ phosphor. The characteristics of the color conversion glass samples, such as luminous efficacy, luminance, CIE (Commission International de I'Eclairage) chromaticity, CCT (Correlated Color Temperature), and CRI (Color Rendering Index) were analyzed according to the PL spectrum. The refractive index of the glass samples was found to increase with the titanium dioxide content. In conclusion, luminous efficacy of color conversion glasses increased as the content of TiO2 was raised in the glass matrix.

화장료의 UV 차단과 은폐효과를 갖는 이산화티탄을 사용하여 자기조직체 형성공법을 적용한 하이브리드 이산화티탄을 제조하고 형태, 성질, 공정의 최적조건과 자외선차단 개선을 확인하였다. 하이브리드 이산화티탄은 마이크로 이산화티탄(250~300nm)의 표면에 나노 이산화티탄(20~30nm)을 자기조직체 형성공법을 이용해 결합시킨, 이산화티탄 대 이산화티탄의 결합체를 말한다. 하이브리드 이산화티탄 제조의 최적조건을 알아내기 위해 (-)을 띄는 마이크로 이산화티탄의 표면에 양이온의 링크로써 AlCl3 를 농도별로 조정하고, 그에 따른 마이크로와 나노 이산화티탄의 투입비율을 달리하여 각각의 조건에서 만들어진 시료를 광학분석, 입도분석, 전위차분석 등을 이용해 확인하고 최적의 제조 조건을 알 수 있었다. 최적의 제조 조건에서 만들어진 하이브리드 이산화티탄의 자외선차단 상승효과를 확인하기 위하여 하이브리드 이산화티탄이 첨가된 화장료와 사용된 하이브리드 이산화티탄과 같은 비율의 마이크로와 나노 이산화티탄을 첨가한 화장료의 SPF in-vitro 를 측정하였고, 15%내지 30%의 자외선차단 상승 효과를 확인하였다.

The β-transus temperature in titanium alloys plays an important role in the design of thermo-mechanical treatments. It primarily depends on the chemical composition of the alloy and the relationship between them is non-linear and complex. Considering these relationships is difficult using mathematical equations. A feed-forward neural-network model with a back-propagation algorithm was developed to simulate the relationship between the β-transus temperature of titanium alloys, and the alloying elements. The input parameters to the model consisted of the nine alloying elements (i.e., Al, Cr, Fe, Mo, Sn, Si, V, Zr, and O), whereas the model output is the β-transus temperature. The model developed was then used to predict the β-transus temperature for different elemental combinations. Sensitivity analysis was performed on a trained neural-network model to study the effect of alloying elements on the β-transus temperature, keeping other elements constant. Very good performance of the model was achieved with previously unseen experimental data. Some explanation of the predicted results from the metallurgical point of view is given. The graphical-user-interface developed for the model should be very useful to researchers and in industry for designing the thermo-mechanical treatment of titanium alloys.

Purpose: Various studies have been conducted on macromolecular materials that not only have basic characteristics but also UV-blocking capabilities. Here we report tinted hydrogel contact lens containing titanium silicon oxide nanoparticles. This study also showed the physical and optical effects of 4-iodoaniline on contact lenses, which affect UV transmissibility. Methods: Titanium silicon oxide nanoparticles were used as additives. HEMA, MA, MMA, 4-iodoaniline and a cross-linker EGDMA were copolymerized in the presence of AIBN as an initiator. The physical properties such as water content, refractive index, contact angle, spectral transmittance of produced contact lenses were measured. Results: Measurement of the physical characteristics of the copolymerized material showed the water content of 38.68~35.01%, refractive index of 1.4350~1.4418, contact angel of 34.15~57.25° and spectral transmittance of 1.0~84.8%. Also, the transmittance for UV light was reduced significantly in combinations containing titanium silicon oxide nanoparticles. Conclusions: Tinted hydrogel contact lens material containing titanium silicon oxide nanoparticles is expected to be able to be used usefully as a material for UV-block hydrogel contact lens.

The purpose of this study is to decrease a stress shielding effect shown in the hip joint. To conduct this study, the clad materials were produced by using an explosion welding method with two materials that were different in the elastic modulus like Ti-6Al-4V alloy and pure Ti. As for the clad materials, the Ti-6Al-4V alloy with large elastic modulus was designed as the neck of femur, and the pure Ti with small elastic modulus as the body of femur. The joints of clad materials formed by the explosion welding showed the typical wave shape, and its thickness was about 0.2㎛. New crystal or grain structure was not formed in the joints. In addition, the Vickers hardness in the joints formed the middle value between the base metal and clad metal. As a result of manufacturing prototype by processing the clad materials in three dimensions, this study gained good shape, and if it is to be applied to clinical in the future, this researcher can expect good results. From the result of this research above, it may be summed up as follows. It is considered as the stress shielding phenomenon showed on the hip joint can be decreased to a certain degree if this researcher is to utilize two clad materials with different elastic modulus like Ti-6Al-4V alloy and pure Ti

In this study, a large modulus of elasticity of the titanium alloy in use, to create artificial hip stress shielding effect appears to reduce the head portion is excellent in the strength of Ti-6Al-4V, making bone pusher which requires low elastic modulus relative modulus of pure titanium grade 2, using a small two metal after welding by explosion welding hip was made. Explosion pressure welding by the welding region with respect to the mechanical properties and the tissue was observed.

This study was aimed at synthesizing and characterizing cerium-doped titania. Cerium-doped anatase titania powders were prepared by sol-gel process, with ammonium (IV) nitrate and titanium (IV) butoxide as the raw materials. The characteristics of pure TiO2 and cerium-doped TiO2 were investigated by XRD, TG/DTA, FE-SEM, and UV-vis spectroscopy. The results of this study show that anatase type of TiO2 was obtained in as-prepared and calcined TiO2 and Ce-TiO2 powder. A DTA curve was also observed as the crystallization temperature decreased with increasing cerium contents. We found that the crystallite size of the obtained anatase particles decreased from 55 nm to 25 nm and the particle size decreased with increasing cerium contents. Moreover, UV-vis spectra showed that anatase titania powders with various cerium contents effectively extend the light absorption properties to the visible region.

목적: 본 연구는 콘택트렌즈 재료로 널리 사용되는 2-hydroxyethyl methacrylate, N-vinyl-2-pyrrolidone, methyl methacrylate, ethylene glycol dimethacrylate에 titanium isopropoxide와 tungsten(VI) oxide 나노입자를 첨가하여 안의료용 렌즈 재료를 중합하였다. 방법: 안의료용 콘택트렌즈의 첨가제로 Tungsten (VI) oxide 나노입자 사용의 활용도를 조사하기 위해 tungsten(VI) oxide 나노입자를 포함한 하이드로젤 콘택트렌즈 재료의 광학적, 물리적 특성 변화를 측정하였다. 결과: 생성된 고분자에 대한 자외선 영역의 투과율은 매우 낮게 측정되어 자외선 차단 능력이 있는 것으로 나타났다. 또한 tungsten(VI) oxide 나노입자의 첨가는 함수율의 큰 변화를 나타내지 않았으나 일정비율을 첨가한 조합에서는 소량의 함수율 변화가 나타났다. 함수율의 큰 변화가 없음에도 불구하고 산소침투율의 측정 값은 tungsten(VI) oxide 나노입자의 첨가 비율이 증가할수록 계속적으로 감소하는 경향이 나타 났다. 결론: 이상의 결과를 통해 titanium isopropoxide 및 tungsten(VI) oxide 나노입자는 하이드로젤 콘택트렌즈의 기본적인 물성을 만족시키면서 기능성 콘택트렌즈 재료로 유용하게 활용될 수 있을 것으로 판단된다.

In this study, porous titanium samples were manufactured by space holder methods using two kinds of urea and sodium chloride space holders. Three-dimensional pore structures were obtained by a computed-tomography (CT) tech- nique and utilized for finite element analysis in order to investigate the mechanical properties. The CT-based finite ele- ment analyses were in better agreement with the experimental results than unit cell model-based analyses. Both the experimental and CT-based results showed the same tendency that the elastic modulus decreased with increasing the porosities. The total porosity of the bulk body plays a key role in determining the elastic modulus of porous materials.

The coastal area of Republic of Korea is very clean compared to other countries. In this reason, west coastal area of our country is a good place for breeding up a fish such as shrimp. In winter season, the heating system is required for preventing shrimp death caused by freezing in the farm. The heater in the heating system for fishery's farm is operated very severe combating corrosion due to high accumulation by feeding material and high temperature in heated sea water. Almost all manufactured heaters of STS 316L and Ti material are scrapped every year due to heavy corrosion such a general and crevice corrosion. For comparing the general and galvanic corrosion in new heater material, the test material of Zirconium (Zr), Titanium (Ti) and STS 316L are tested by potentiodynamic polarization, electrochemical impedance spectroscopy (EIS), current density-time methods and microscopic examination in a 3.5% NaCl solution. The corrosion potential (Ecor) measured by potentiodynamic polarization for Zr, Ti and STS 316L reveals -198, -250 and -450mV, corrosion current density 0.5, 2.5 and 6.5μA/cm2 respectively. The film resistance measured by EIS are Zr 63,000, Ti 39,700 and 316L 3,150Ω, and the current of Zr-Ti couple is 0.03μA, whereas Zr-316L SS is 0.1μA. According to the result of this experiment in 3.5% NaCl solution, Zr is excellent corrosion resistance material than Ti and STS 316L.

Electrochemical surface treatment is commonly used to form a thin, rough, and porous oxidation layer on the surface of titanium. The purpose of this study was to investigate the formation of nanotubular titanium oxide arrays during short anodization processing. The specimen used in this study was 99.9% pure cp-Ti (ASTM Grade II) in the form of a disc with diameter of 15 mm and a thickness of 1 mm. A DC power supplier was used with the anodizing apparatus, and the titanium specimen and the platinum plate (3mm×4mm×0.1mm) were connected to an anode and cathode, respectively. The progressive formation of TiO2 nanotubes was observed with FE-SEM (Field Emission Scanning Electron Microscopy). Highly ordered TiO2 nanotubes were formed at a potential of 20 V in a solution of 1M H3PO4 + 1.5 wt.% HF for 10 minutes, corresponding with steady state processing. The diameters and the closed ends of TiO2 nanotubes measured at a value of 50 cumulative percent were 100 nm and 120 nm, respectively. The TiO2 nanotubes had lengths of 500 nm. As the anodization processing reached 10 minutes, the frequency distribution for the diameters and the closed ends of the TiO2 nanotubes was gradually reduced. Short anodization processing for TiO2 nanotubes of within 10 minutes was established.

Cold spray deposition using Titanium powder was carried out to investigate the effects of powder morphology and powder preheating on the coating properties such as porosity and hardness. The in-flight particle velocity of Ti powder in cold spray process was directly measured using the PIV (particle image velocimetry) equipment. Two types of powders (spherical and irregular ones) were used to manufacture cold sprayed coating layer. The results showed that the irregular morphology particle appeared higher in-flight particle velocity than that of the spherical one under the same process condition. The coating layer using irregular morphology powder represented lower porosity level and higher hardness. Two different preheating conditions (no preheating and preheating at ) were used in the process of cold spraying. The porosity decreased and the hardness increased by conducting preheating at . It was found that the coating properties using different preheating conditions were dependent not on the particle velocity but on the deformation temperature of particle. The deposition mechanism of particles in cold spray process was also discussed based on the experimental results of in flight-particle velocity.

The purpose of this study was to assess the efficacy of photodynamic therapy (PDT) using erythrosine and a halogen light source to treat a biofilm formed on a machined surface titanium disk in vivo. Ten volunteers carried an acrylic appliance containing six machined surface titanium disks on the upper jaw over a period of five days. After the five days of biofilm formation period, the disks were removed. PDT using 20 μM erythrosine and halogen light was then applied to the biofilms formed on the disks. Experimental samples were divided into a negative control group (no erythrosine and no irradiation), E0 group (erythrosine 60s + no irradiation), E30 group (erythrosine 60s + halogen light 30s), and E60 group (erythrosine 60s + halogen light 60s). Following PDT, the bacteria in the biofilm were found to be detached from each disk. Each suspension with detached bacteria were diluted and cultivated on a blood-agar plate for five days under anaerobic conditions. The cultivated bacterial counts in the E60 group were significantly lower than the control group (86.4%) or E0 group (76.7%). In the experimental groups also, the light exposure time and bacterial counts showed a negative correlation. In conclusion, PDT using erythrosine and halogen light has bactericidal effects on biofilms formed on a titanium disk in vivo. Notably, applying 20 μM erythrosine and 60 seconds of halogen light irradiation had a significantly potent effect.

was successfully formed on a Ti specimen by MAO (Micro-Arc-Oxidation) method treated in electrolyte. This study deals with the influence of voltage and working time on the change of surface microstructure and phase composition. Voltage affected the forming rate of the oxidized layer and surface microstructure where, a low voltage led to a high surface roughness, more holes and a thin oxidized layer. On the other hand, a high voltage led to more dense surface structure, wider surface holes, a thick layer and fewer holes. Higher voltage increases photocatalytic activity because of better crystallization of the oxidized layer and good phase composition with anatase and rutile , which is able to effectively separate excited electrons and holes at the surface.

The aim of this study was to evaluate surface character¬istics and biological properties of the dentin -derived hydroxyapatite (HA) coating on titanium substrate. Dentin-derived HA was obtained from extracted human teeth using a calcination method at 850℃. The commercially pure titanium (cp-Ti, ASTM Grade II) was used as a metallic substrate and a radio frequency magnetron sputtering method was employed as a coating method. Scanning electron microscopy (SEM) and energy dispersive X-ray analysis (EDX) were utilized to investigate the coating aspects and composition. Atomic forced microscopy (AFM) and a surface profiler were used to assess the surface morphology and roughness. Corrosion tests were performed in phosphate- buffered saline at a 36.5 ± 1℃ in order to determine the corrosion behavior of the uncoated and coated specimens. The biocompatibility of dentin-derived HA coated specimens with fetal rat calvarial cells and human gingival fibroblasts was assessed by SEM and cell prolif¬eration analysis. The results showed that the dentin-derived HA coatings appeared to cover thinly and homogeneously the surfaces without changing of the titanium substrate. The EDX analysis of this the coating surface indicated the presence of Ca and P elements. The mean surface roughness of cp-Ti and dentin-derived coating specimens was 0.27 µm and, 1.7 µm, respectively. Corrosion tests indicated a stable passive film of the dentin-derived HA coating specimens. SEM observations of fetal rat calvarial cells and human fibroblast cells on coated surfaces showed that the cells proliferated and developed a network of dense interconnections. The cells on all specimens proliferated actively within the culture period, showing good cell viability. At day 1 and 3, dentin-derived coating specimens showed 89% and 93% cell viability, respectively, when normalized to cp-Ti specimens. These results suggest that dentin-derived HA coating using the RF magnetron sputtering method has good surface characteristics and biocompatibility.

This study was performed to fabricate the porous titanium foam by space holder method using NaCl powder, and to evaluate the effect of NaCl volume fractions (33.3~66.6 vol.%) on the porosities, compressive strength, Young's modulus and permeability. For controlling pore size, CP titanium and NaCl particles were sieved to different size range of 70~150 and 300~425 respectively. NaCl of green Ti compact was removed in water followed by sintered at for 2 hours. Total porosities of titanium foam were in the range of 38-70%. Pore shape was a regular hexahedron similar that of NaCl shape. Porous Ti body showed that Young's modulus and compressive strength were in the range of 0.6-6 GPa and 8-127 MPa respectively. It showed that pore size and mechanical properties of Ti foams was controllable by NaCl size and volume fractions.

Zr-Ti alloy powders were successfully synthesized by magnesium thermal reduction of metal chlorides. The evaporated and mixed gasses of were injected to liquid magnesium and the chloride components were reduced by magnesium leading to the formation of . The released Zr and Ti atoms were then condensed to particle forms inside the mixture of liquid magnesium and magnesium chloride, which could be dissolved fully in post process by 1~5% HCl solution at room temperature. By the fraction-control of individually injected and gasses, the final compositions of produced alloy powders were changed in the ranges of Zr-0 wt.%~20 wt.%Ti and their purity and particle size were about 99.4% and the level of several micrometers, respectively.

The purpose of this study was to investigate the effect of cytokine-induced osteoclastogenesis on tooth movement related to orthodontic force. We evaluated the cytotoxicity as well as the expression of OPG and RANKL, which influence the homeostasis of bone metabolism. Titanium particles were applied to human periodontal ligament cells and subcultured fourth generation cells. The ALP assay and the MTT assay were used to assess changes in cytotoxicity. After 48 hours, cytotoxicity increased proportionally with the concentration of titanium. With 20 mg, the cytotoxicity was the lowest. R T-PCR was u sed for assessing m R NA l evels of O PG a nd R ANKL; after 96 hours, t he m R NAs of O PG a nd R ANKL increased steeply. A western blot analysis showed that with 20 mg of titanium, the protein expression of OPG increased linearly with time, especially a fter 96 hours, while t he p rotein e xpression o f RANKL d id n ot s how significant changes with titanium processing. Given the increase in OPG expression after the initial cytotoxicity, changes in cytotoxicity with titanium may be attributable to the antagonistic effect of OPG on cytotoxicity