In this paper, the injectors with normal quantity, over quantity of +10%, under quantities of -10% and –30%, were mounted on S-ENG and P-ENG in order to measure the voltage energy, current energy and power supplied to the injectors and the fuel economy under several speed of rpm conditions. The voltage and current energy of S-ENG was greater than P-ENG, and the power of S-ENG was measured and analyzed 4.8 times higher than that of P-ENG at all injectors, and the tendency of carbon dioxide emissions calculated from fuel efficiency measurement results was not significantly affected by the type of injectors, but P-ENG was measured to be slightly affected by the type of injectors. It is assumed that the model year and mileage of the test vehicle affects this tendency.

In this paper, we investigate the relationship between control system of Bosch system and that of Delphi system by measuring the high and low voltage waveform, current waveform and fuel injection quantity of D-2 and R- engines. Waveform measurements are used the PICO scope and the CDS tester. The injectors of D-2 and R-engines were tested under no load condition using injector with normal fuel injection quantity, injector with small fuel injection quantity and injector with many fuel injection quantity. The relation between current energy and fuel injection quantity shows that the injector variation rate of D2-engine is much larger than that of R-engine. The injector current energy of the D2-engine was more linear than that of the R-engine, therefore making the system more stable. Although the control system of the D2-engine is a more stable system only in terms of the durability of the internal parts of the injector, the injector of the R-engine has a good response because the current value is large.

In this paper, we investigate the relationship between fuel injection quantity and voltage and current energy of Bosch system and Delphi system by measuring the high and low voltage waveform, current waveform, fuel injection quantity and fuel pressure of A and J-engines. Waveform measurements are made using the PICO scope and the CDS tester. The injectors of A and J engines were tested under no load condition using injector with normal fuel injection quantity, injector with small fuel injection quantity and injector with many fuel injection quantity. In case of normal injector, A-engine has higher fuel pressure, injection interval time, voltage energy, and current energy than J-engine. The current energy of the A-engine changed linearly compared to that of the J-engine. For over and under injectors, the change in the previous physical quantity was greater for the A-engine than for the J-engine. However, the duration time of maintaining to open the injector is controlled differently, and so the voltage and current energy values are changed, and the change of the current energy is larger than the voltage energy.

This study analyzed by measuring the voltage waveform of the injector intended for operating CRDI diesel vehicle. The cases of the EGR trouble and a EGR normal is considered. 1) The voltage waveform in the case of the normal and trouble, the difference between the maximum voltage was not large, decrease in the number of voltage gated pulses with the increase in engine speed, sustained current remained for this period. 2) The voltage waveform, comparing the case of the normal case and trouble, the size of the maximum voltage, no large change in gate pulse voltage is to be generated than in the case of a defective irregular longer opening time of the injector factor it was possible to know the bad influence on the fuel efficiency.

Abstract Dielectric barrier discharge (DBD) in air, which has been established for the production of large quantities of ozone, is more recently being applied to a wider range of aftertreatment processes for HAPs (hazardous air pollutants). Although DBD has high electron density and energy, its potential use as precharging nano and submicron sized particles, is not known. In this work, we measured V‐I (voltage‐current) characteristics of DBD and estimated the collection efficiency of particles with bimodal distribution by DBD type 2‐stage ESP (electrostatic precipitator). To examine the particle collection with various applied voltage waveforms of DBD, nano size particles of NaCl (20∼100 nm) and DOS (50∼800 nm) were generated by an electrical tube furnace and an atomizer, respectively. Particle collection efficiencies of all the cases increased with increase of DBD electric power that the results corresponded to product of V by I whose magnitudes were the largest in triangular voltage waveform.