이 연구는 코르크보드를 보강하여 건축부재 및 놀이기구의 안전부재 등으로 폭넓게 활용할 것을 목적으로 코르크보드의 중층에 금속, 유리섬유, 탄소섬유를 삽입하여 보강한 3종의 코르크복합보드를 제조하였고, 코르크복합보드의 수분흡수에 따른 치수안정성 및 접착층 박리성능을 조사하였다. 코르크복합보드의 흡수율은 0.37% - 0.45%의 범위에 있었고, 코르크보드에 비해 0.61배 - 0.74배의 낮은 값을 나타내었다. 코르크복합보드의 두께팽창률은 0.92% - 1.58%의 범위에 있었고, 코르크보드 보다 1.4 - 2.4배의 높은 값을 나타내었다. 그러나 이 값들은 일반 목질보드보다 현저히 낮았고, KS규격의 12%이하를 하회하는 것이 확인되었다. 코르크복합보드의 준내수 및 내수침지박리시험후의 접착층박리율은 0%로 전혀 접착층의 박리가 일어나지 않아 우수한 내수성을 나타내었고, 흡수율과 흡수두께팽창률은 상온침지에 비해 다소 증가하였으나, 목질보드에 관한 KS규격을 하회하는 우수한 치수안정성을 나타내는 것이 확인되었다.

In recent, fiber-reinforced composites have been widely used in many fields because of their excellent performance. In order to manufacture lightweight, high-performance, and inexpensive composites various laminated structures were designed. Six types of hybrid composites were fabricated with glass/basalt/aramid fibers by VARTM process. The effect of the laminated structure on the mechanical properties of composites was investigated through impact energy, tensile and bending strength. Compared to other conditions more higher impact energy was obtained when the aramid fibers were in the center position and more higher bending strength was obtained when the fibers are laminated in the order of increasing bending performance from top to bottom. The laminate structure did not affect tensile strength which mainly depends on the property of fibers.

전 세계적으로 건설폐기물에 의한 환경문제에 대한 관심이 증가하고 있다. 이에 따라 건설재료들에 대한 재활용방안 에 대한 연구가 많이 진행되고 있다. GFRP는 최근 구조물의 보강에 많이 사용되는 건설 재료이다. 본 연구에는 GFRP를 분쇄하 여 만든 재활용 GFRP파우더(RGP)의 잔골재 대체 가능성을 검토하고자 하였다. RGP는 GFRP의 제작 시 발생되는 GFRP 잉여물을 분쇄하여 사용하였다. RGP의 잔골재 치환율을 20%, 40% 60% 80%로 설정하였다. RGP가 혼합된 시멘트 모르타르의 재료 성능을 검토하기 위하여 압축강도, 쪼갬인장강도 및 휨 강도를 측정하였다. 실험결과, RGP의 혼입으로 시멘트 모르타르의 기초물성이 증가하는 경향이 나타났다. 본 연구결과는 장기적으로 GFRP의 건설재료로의 재활용을 위한 기초자료로 활용이 가능할 것으로 판단된다.

Cured-in-place-pipe(CIPP) is the most adopted trenchless application for sewer rehabilitation to extend the life of the existing sewer without compromising both direct construction and indirect social costs especially applied in the congested urban area. This technology is globally and domestically known to be the most suitable for partial and full deteriorated pipe structure rehabilitation in a sewer system. The typical design of CIPP requires a significant thickness of lining to support loading causing sewage flow interruption and increasing material cost. This paper presents development of a high strength glass fiber composite lining material for the CIPP application and structural test results. The test results exhibit that the new glass fiber composite lining material has 12 times of flexural strength, 6.2 times of flexural modulus, and 0.5 Creep Retention Factor. These test results can reduce lining design thickness 35% at minimum. Even though taking into consideration extra materials such as outer and inner films for actual field applications, the structural capacity of the composite material significantly increases and it reduces 20 percent or more line thickness as compared to the conventional CIPP. We expect that the newly developed CIPP lining material lowers material costs and minimizes flow capacity reduction, and fully replaceable to the conventional CIPP lining materials.

In this study, glass fibers are fabricated via a continuous spinning process using manganese slag, steel slag, and silica stone. To fabricate the glass fibers, raw materials are put into an alumina crucible, melted at 1550℃ for 2 hrs, and then annealed at 600℃ for 2 hrs. We obtain a black colored glass. We identify the non-crystalline nature of the glass using an XRD(x-ray diffractometer) graph. An adaptable temperature for spinning of the bulk marble glass is characterized using a high temperature viscometer. Spinning is carried out using direct melting spinning equipment as a function of the fiberizing temperature in the range of 1109℃ to 1166℃ , while the winder speed is in the range of 100rpm to 250rpm. We investigate the various properties of glass fibers. The average diameters of the glass fibers are measured by optical microscope and FE-SEM. The average diameter of the glass fibers is 73 μm at 100rpm, 65 μm at 150rpm, 55 μm at 200rpm, and 45 μm at 250rpm. The mechanical properties of the fibers are confirmed using a UTM(Universal materials testing machine). The average tensile strength of the glass fibers is 21MPa at 100rpm, 31MPa at 150rpm, 34MPa at 200rpm, and 45MPa at 250rpm.

PURPOSES: The objective of this study is to evaluate the physical properties of recycled asphalt mixtures reinforced with glass fiber. METHODS: Firstly, mixing design was conducted on recycled asphalt mixture for use of 50% recycled aggregate. Various laboratory tests were performed on four types of recycled asphalt mixtures with different glass fiber content to evaluate the physical properties. The laboratory tests include indirect tensile strength test, dynamic modulus test, Hamburg wheel tracking test and tensile-strength ratio to evaluate cracks, rutting and moisture resistance of mixtures. RESULTS: The indirect tensile strength of fiber reinforced glass increased about 139.4%. As a result of comparing the master curves obtained by the dynamic modulus test, the elasticity was low in the low temperature region and high in the high temperature region when the glass fiber was reinforced. The glass fiber contents of PEGS 0.3%, Micro PPGF 0.1% and Macro PPGF 0.3% showed the highest moisture resistance and rutting resistance. CONCLUSIONS : The test results show that use of glass fiber reinforcement can increase the resistance to cracking, rutting, and moisture damage of asphalt mixtures. It is also necessary to validate the long-term performance of recycled asphalt mixtures with glass fiber using full scale pavement testing and field trial construction.

General D-glass(Dielectric glass) fibers are adaptable to PCBs(Printed circuit boards) because they have a low dielectric constant of about 3.5~4.5. However, very few papers have appeared on the physical characteristics of D-glass fibers. D-glass fibers were fabricated via continuous spinning process using bulk D-glass. In order to fabricate the D-glass, raw materials were put into a Pt crucible, melted at 1650℃ for 2 hrs, and then annealed at 521 ± 10℃ for 2 hrs. We obtained transparent clear glass. The transmittance and adaptable temperature for spinning of the bulk marble glass were characterized using a UV-visible spectrometer and a viscometer. Continuous spinning was carried out using direct melting spinning equipment as a function of the fiberizing temperature in the range of 1368℃ to 1460℃, while the winder speed was between 100 rpm and 200 rpm. We investigated the physical properties of the D-glass fibers. The average diameters of the glass fibers were measured by optical microscope and FE-SEM. The average diameters of the D-glass fibers were 21.36 um at 100 rpm and 34.06 um at 200 rpm. The mechanical properties of the fibers were confirmed using a UTM(Universal materials testing machine). The average tensile strengths of the D-glass fibers were 467.03 MPa at 100 rpm and 522.60 MPa at 200 rpm.

E (Electric) -glass fibers are the most widely used glass fibers, taking up 90 % of the long glass fiber market. However, very few papers have appeared on the physical characteristics of E-glass fibers and how they depend on the fiberizing temperature of fiber spinning. Glass fiber was fabricated via continuous spinning process using bulk E-glass. In order to fabricate the E-glass specimen, raw materials were put into a Pt crucible and melted at 1550 oC for 2hrs; mixture was then annealed at 621 ± 10 oC for 2hrs. The transmittance and adaptable temperature for spinning of the bulk marble glass were characterized using a UV-visible spectrometer and a viscometer. Continuous spinning was carried out using direct melting spinning equipment as a function of the fiberizing temperature in the range of 1175~1250 oC, while the winder speed was fixed at 500 rpm. Subsequently we investigated the physical properties of the E-glass fiber. The average diameter of the synthesized glass fiber was measured by optical microscope. The mechanical properties of the fiber were confirmed using a UTM (universal materials testing machine); the maximum tensile strength was measured and found to be 1843 ± 449MPa at 1225 oC.

In this study, material characteristics of glass fiber composite were evaluated by experiment. Tensile, compression and in-plane shear test were performed as test method of ASTM. Velocity of Tensile and compression test was 2mm/min and in-plane shear test was 4mm/min. At the test result, elastic modulus of tensile and compressive were similar. Maximum compressive strength and maximum compressive strain were smaller than the maximum tensile strength and maximum tensile strain.

S-2유리섬유직물과 폴리에스터 수지로 구성된 적충복합재료를 케블라 49 Thread로 1/2인치, 1인치 2인치 간격으로 스티칭하여 스티칭 간격에 따른 물성과 충격 강도의 변화로부터 최적스티칭 조건을 구하였으며 또한 스티칭하지 않은 적층복합재료와의 물성차를 비교연구하였다. 인장실험과 3점굽힘실험을 통해 시편의 종류별 기본 물성을 알아보았고, 234.7J의 충격에너지를 가해 시편의 파단 현상과 에너지 흡수 능력을 조사하였다. 파단에너지의 약 50% 정도인 110.2J의 충격에너지로 3회 반복실험하여 시편의 손상정도와 충격강도를 비교 검토하였다. 인장실험과 굽힘 실험의 결과 1인치 간격으로 스티칭한 시편이 가장 높은 강도를 보였으며, 충격실험에서도 가장 뛰어난 에너지 흡수능력 및 손상에 대한 저항을 보였다. 반복충격 실험의 결과 스티칭하지 않은 시편은 현저한 충격강도의 감소를 보인 반면 스티칭한 시편은 반복충격에도 에너지 흡수능력이 우수하게 유지되었다. C-scanning으로 손상부위를 관찰한 결과 스티칭으로 인해 손상영역의 확산이 억제되어 현저히 감소함을 보여주었다. 스티칭 간격이 너무 조밀한 경우 강도의 향상보다는 스티칭으로 인한 손상이 더 커져서 1/2인치 간격으로 스티팅한 시편의 경우는 인장강력이나 충격에너지 흡수가 스티칭하지 않은 시편에 비해 오히려 감소하는 결과를 나타내었다. 그러나 이러한 감소에도 불구하고 외부충격에 의한 손상영역의 확산은 효과적으로 억제되어 국부적인 손상만이 발생함을 알 수 있었다.

Municipal solid wastes incinerator (MSWI) bottom ash and melting slag are used to prepare external panel for increasingthe recycling rate of them in this study. In case of external panel, the most important property is flexural strength. Becauseit is easily distorted by external force. Wasted glass fiber (below WGF) is used to increase the flexural strength of externalpanel. Flexural strength of prepared panel was 14.6MPa of the mixing ratio of 3.0wt% WGF. But compressive strengthwas decreased with the addition of WGF. Because L/S ratio has to be increased to enhance the workability at high additionamount of WGF. High liquid content hinders geopolymer formation. But compressive strength (about 20MPa) was notlow at this condition.

In this study, the tensile properties of FRP in the oceanic environment were compared. The tensile properties at room temperature and sea water temperature were compared and the tensile properties according to the the salt stress permeation duration are compared. It is appeared that the difference in the tensile properties of composite materials due to the temperature difference very little, and it is appeared that the tensile difference due to salt stress permeation by the types of glass fiber has a difference.