As the demand for appropriate heat dissipation measures to improve product stability and performance continues to increase and product design becomes highly integrated, research to improve heat transfer performance while maintaining the same area or size is required. In this study, the sample-shaped aluminum plate was treated as upper-coating, and the thickness of the coating was divided into 1mm, 2mm, and 3mm, respectively, and the coating material was applied with silver, copper, and graphene. The temperature condition of the heat source was set to 473K, and heat dissipation analysis was performed under natural convection. The thermal performance was compared and analyzed through temperature distribution, flow velocity distribution, and heat flux, and it was confirmed that the high thermal conductivity of graphene compared to other materials had a dominant effect on the increase in the conduction heat transfer rate. And it was confirmed that the high surface temperature of the graphene coating also increased the heat transfer rate by convection, thereby enhancing the heat dissipation effect.

Asphalt concrete(Ascon) is used to repair potholes and cracks. Special truck-mounted cargo boxes transport 200℃ asphalt concrete to repair potholes and cracks. However, long working and transportation hours to repair wide roads decrease the temperature of the asphalt concrete inside the cargo boxes. If the asphalt concrete temperature drops below 170℃, the adhesion with roads that need repair decreases. Therefore, the temperature of the asphalt concrete needs to be maintained for a long time. Conventional asphalt concrete cargo boxes are mostly burner-type models using hot air to prevent the temperature of the asphalt concrete from dropping. However, there are significant temperature differences between the asphalt concrete near and far away from the hot air, so the temperature decreases over time and leads to the disposal of large amounts of asphalt concrete. This causes waste of resources and environmental pollution. Therefore, this study proposed a heat dissipation cut-off type cargo box model to solve this problem and demonstrated its performance over conventional burner-type models through tests and analysis.

본 연구에서는 DVR 내부 공기유동을 직접 제어하여 CPU의 온도를 낮추기 위한 유동제어 구조물을 제안하였다. 제안된 구조물은 세 개의 얇은 판의 형태로 구성되었으며, DVR 내부의 공기 유동을 포괄적으로 제어하여 CPU의 효율적인 방열을 유도하고자 하였다. DOE와 RSM을 이용한 매개변수 연구기법을 통해 유동제어 구조물의 형상을 최적화하였으며, 해석에는 유한체적방법을 이용한 유체역학 분석 패키지인 FlowVision을 사용하였다. 실제 DVR 기기에서의 실험을 통해 해석 결과를 검증한 결과 CPU의 온도가 16.1℃ 낮아짐을 확인하였다

Composite materials consisting of pure aluminum matrix reinforced with different amounts of graphite particles are successfully fabricated by mechanical ball milling and spark plasma sintering (SPS) processes. The shrinkage rates of the composite powders vary with the amount of graphite particles and the lowest shrinkage value is observed for the composite with the highest amount of graphite particles. The current slopes of time increase with increase in the amount of graphite particles whereas the current slopes of temperature show the opposite trend. The highest thermal conductivity is achieved for the composite with the least amount of graphite particles. Therefore, the thermal properties of the composite materials can be controlled by controlling the amount of the graphite particles during the SPS process.

LEDs are increasingly used for many applications including automotive, display and special lighting applications. The performance and lighting characteristics of the LED depend on cooling condition because the power LED generates lots of heat. In this study, the effect of the generated heat from power LED module on lighting characteristics and performance is measured and evaluated. For experiments, the transient temperature of a power LED module with cooling condition is measured.

In recent years, conventional streetlight is replaced by LED streetlight to reduce power consumption dramatically and to maximize lighting effects. However the characteristic of power LED itself driven by high current to increase the illumination, we need

In this study, copper vapor chambers with built-in cooling fins, which eliminated the soldered or brazed joints in the conventional vapor chamber, were fabricated using the metal injection molding process. The results show that with optimized molding parameters, fins with an aspect ratio up to 18 could be produced. After sintering, the densities of the fin and chamber reached 96%. With only 32 cooling fins and a small fan installed, the thermal resistance of the heat sink was 1.156 ℃/W, and the power dissipation was 40W when the junction temperature was 70℃. When copper powder was sintered onto the chamber to make a vapor chamber, the thermal resistance decreased to 1.046℃/W.