Nano-sized TiO2-60 wt% SrO composite powders were synthesized by a sol-gel method using titanium isopropoxide and Sr(OH)2 · 8H2O as precursors. 3, -5, -7 wt%Ag spot-coated TiO2-60 wt% SrO composite powders were synthesized by a Ag electroless deposition method using TiO2-60 wt% SrO composite powders calcined at 1050˚C, which mainly exhibited the SrTiO3phase. However, a small number of rutile TiO2, Sr2TiO4 and SrO2 phases were also detected. In the Ag spot-coated powders synthesized by electroless deposition, nano-sized particles about 5-25 nm in diameter adhered to the TiO2-60 wt% SrO composite powders. The photocatalytic activity of Ag spot-coated TiO2-SrO and TiO2-SrO composite powders for degradation of phenol showed that all of TiO2-SrO composite powders were highly active under UV light irradiation. 7 wt%Ag spot-coated TiO2-60wt.%SrO composite powders had a relatively higher photocatalytic activity than did TiO2-SrO composite powders under visible light.

In order to investigate the effect of doping C, N, B and F elements on TiO2 for reducing the band gap, the heat treatment of TiO2 was carried out with tetraethylammonium tetrafluoroborate. Through XRD and XPS analysis, the C, N, B and F doped anatase TiO2 was confirmed. According to the increase of temperature during treatment, the particle size was increased due to aggregation of TiO2 with elements (B, C, N and F). To investigate the capacity of photocatalyst for degradation of dye under solar light, the degradation of acridine orange and methylene blue was conducted. The degradation of dyes was carried out successfully under solar light indicating the effect of doping elements (B, C, N and F) on TiO2 for reducing the band gap effectively.

xTiO2-ySiO2 system photocatalysts were developed by sol-gel method based on the change of production parameters, and their structure of crystallization and the specific surface area were measured. Considering the efficiency of the ethanol and phenol degradation using the catalyst, the conclusions were obtained as follows: By means of X-ray analysis of xTiO2-ySiO2 powder that is obtained from Titanium and Silicon alkoxide by sol-gel process, it is shown that crystal structure of anatase type is a dominating structure and, on the other hand, the structure of rutile also partly exists. The increase of SiO2 contents causes the decrease of the degree of crystallization of the gel, whereas the specific surface area preferentially increases. It is shown that more than 90% of ethanol and phenol are degraded when reaction time is about three and an hours, and the maximum degradation rate of ethanol and phenol is shown in 60TiO2-40SiO2 catalyst.

Carbon Nano Tubes could be either metallic or semi-conducting in nature, depending on their diameter. Its photocatalytic behavior has given an impetus to use it as an anti-microbial agent. More than 95% Escherichia coli and Staphylococcus aureus bacteria got killed when exposed to Carbon Nano Tubes for 30 minutes in presence of sunlight. Carbon Nano Tubes are supposed to have smooth surface on to which it accumulates positive charges when exposed to light. The surface that is non illuminated has negative charge. At the cellular level microorganisms produce negative charges on the cell membrane, Therefore damaging effect of multi walled carbon nano tubes (exposed to light) on the microorganisms is possible. In this paper, photo catalytic killing of microbes by multi walled carbon nano tubes is reported. Killing was due to damage in the cell membrane, as seen in SEM micrographs. Moreover biochemical analysis of membrane as well as total cellular proteins by SDS PAGE showed that there was denaturation of membrane proteins as well as total proteins of both the microbes studied. The killed microbes that showed a decrease in number of protein bands (i.e. due to breaking down of proteins) also showed an increase in level of free amino acids in microbes. This further confirmed that proteins got denatured or broken down into shorter units of amino acids. Increased level of free amino acids was recorded in both the microbes treated with multi walled carbon nano tubes and sunlight.

[ TiO2 ]ACF composites were prepared by the electrochemical method with Titanium (IV) n-butoxide (TNB) electrolyte under different electrochemical operation time. The BET surface area for TiO2/ACF composites decrease with the increase of electrochemical operation time. There is a single crystal structure which is anatase in all of the samples from the data of XRD. The SEM micrphotographs of TiO2/ACF composites show that the TiO2 particles were well mixed with the ACF. There are O and P with strong C and Ti peaks in all samples from EDX results, and it also shows that a decrease of the C content with a increasing of Ti content with increasing of the electrochemical operation time in the over all composites. DSC cures show that the exothermic peak of all composites at 560℃ represents the transformation heat of amorphous parts to anatase phase and the discontinuous grain growth of the transformed anatase particles. Finally, the excellent photoactivity of TiO2/ACF composites (especially, ACFT10) could be attributed that the decrease of concentration of MB can be concluded to be much faster for the adsorption by ACF than for photocatalytic decomposition by TiO2.

This paper presents applicability of photocatalytic decomposition of methyl mercaptan using TiO2. A quartz reactor was used in order to elucidate reaction pathway in photocatalytic decomposition of methyl mercaptan. Experimental results showed that more than 99.9% of methyl mercaptan was decomposed within 30 minutes. It was found that the photocatalytic decomposition of methyl mercaptan followed pseudo first order and its reaction coefficient was 0.05min-1 During 30 minutes in the photocatalytic reaction, the concentration of methyl mercaptan, dimethyl disulfide, SO2, H2SO4, COS, H2S were determined. These results showed that 64% of methyl mercaptan were compensated for the increase in sulfur after 30 minutes through the mineralization. The proposed main photocatalytic decomposition pathway of methyl mercaptan was methyl mercaptan→dimethyl disulfide→SO2→H2SO4.

광촉매 반응이 자연유기물에 의한 나노여과막의 오염에 미치는 영향을 살펴보았다. 광촉매 분해공정은 자연유기물의 분해와 변형에 효율적이었으며 이산화티타늄과 고정화 비드를 광촉매로 사용하였다. 광촉매적 특성을 비교하기 위하여 칼슘 이온 존재 시의 휴민산의 광분해를 모델 반응으로 설정하였다. 광분해 전에는 치밀한 막오염층이 형성되어 막오염을 가속화시킨 반면, 광분해 후에는 막오염이 크게 감소하였다.

In this work, activated carbon (AC) after HNO3 modification was used as the support during the production of supported TiO2 to increase the high deposition efficiency and the photocatalytic activity. The results of N2 adsorption showed that the BET surface area of samples decreased with an increasing of the concentration of HNO3 due to the penetration of TiO2. From XRD data, a single crystal structure of anatase peak was observed in diffraction patterns for the AC coated with titanium complexes. From the SEM results, almost all particles were aggregated with each other at the carbon surface and AC was covered with TiO2 particles in all of the samples. The EDX spectra show the presence of C, O, Ti and other elements. It was also observed a decreasing of amount of C content with increasing Ti and O content from the EDX. The results of FT-IR revealed that the modified AC contained more surface oxygen bearing groups than that of the original AC. The effect of surface acidity and basity calculated from Boehm titration method was also evaluated from correlations as a function of NaOH, NaHCO3, and Na2CO3 uptake. The surface modification of AC by HNO3 leads to an increase in the catalytic efficiency of AC/TiO2 catalysts, and the catalytic efficiency increases with increasing of HNO3 concentration.

Carbon/TiO2 composites were prepared by CCl4 solvent mixing method with different mixing ratios. Since the carbon layers derived from pitch on the TiO2 particles were porous, the Carbon/TiO2 composite series showed a good adsorptivity and photo decomposition activity. The BET surface area for the carbon layer in the sample increases to increasing with pitch contents. The SEM results present to the characterization of porous texture on the Carbon/TiO2 composite and pitch distributions on the surfaces for all the materials used. From XRD data, a weak and broad carbon peak of graphene with pristine anatase peaks were observed in the X-ray diffraction patterns for the Carbon/TiO2. The EDX spectra show the presence of C, O and S with strong Ti peaks. Most of these samples are richer in carbon and major Ti metal than any other elements. Finally, the excellent photocatalytic activity of Carbon/TiO2 with slope relationship between relative concentration (C/C0) of MB and t could be attributed to the homogeneous coated pitch on the external surface by CCl4 solvent method.

It prepared the TiO2 powder which has photo-catalytic activity in the visible-light by the wet process with titanium oxysulfate. The titanium dioxide(TiO2) by the wet process creates a new absorption band in the visible light region, and is expected to create photocatalytic activity in this region. Anatase TiO2 powder which has photocatalytic activity in the visible light region, is treated using microwave and radio-frequency(RF) plasma. But, the TiO2 powder for the visible light region, which also can be easily produced by wet process. The wet process TiO2 absorbed visible light between 400nm and 600nm, and showed a high activity in this region, as measured by the oxidation removal of aceton from the gas phase. The AH-380 sample appears the yellow color to be strong, the catalytic activity in the visible ray was excellent in comparison with the plasma-treated TiO2. The AH-380 TiO2 powder, which can be easily produced on a large scale, is expected to have higher efficiency in utilizing solar energy than the plasma-treated TiO2 powder.

Sr2Ta2O7, a layered perovskite compound, has been reported to possess most excellent photocatalytic properties among the layered perovskite materials. Recently, we have demonstrated that Ba5Ta4O15 that was prepared under a mol ratio of Ba: Ta=1:1 has high photocatalytic performance as well as Sr2Ta2O7. In this study, the photocatalyst samples with a mol ratio of Sr: Ba: Ta = (1-x): x: 1 were prepared. The maximum photocatalytic performance was obtained for x= 0.2, which is three times as high as that of undoped Sr2Ta2O7.

The photocatalytic degradation of methylene blue(MB) was investigated using TiO2 as photocatalyst and UV radiation. TiO2 supported with activated carbon(AC) was prepared by SOL-GEL method and depended on several parameters such as the mass ratio of TiO2/AC, pH and experimental time. The presence of the anatase and rutile crystal phase was determined by XRD analyses of the prepared TiO2. The degradation of MB with TiO2/AC was about 20% higher than that of AC alone. A variation of photodegradation was negligible under UV radiation conditions ( ≥ 40W). It was experimentally showed that the photodegradation rate was increased with increasing the amount of photocatalyst. The optimal catalyst was prepared by impregmation of 5wt%-TiO2 with AC and was calcined at 300℃, and showed about 99% removal efficiency for 3hrs.

Activated carbon fiber (ACF) filters are widely used to remove volatile organic compounds (VOCs) in air cleaning devices. The performance of ACF filters could be enhanced combining adsorption process with photodegradation process. In this study, to investigate this enhancement effect, a duct-type reactor was made and TiO2 was i㎜obilized on a co㎜ercialized ACF filter. Benzene, toluene, and m-xylene (BTX) were chosen as target compounds. Removal experiments for BTX were done under different air velocity and upstream concentration conditions. The range of inlet concentration was 200～1,400 ppb and the air velocities were 0.4, 0.7 and 1.0 m/s. Adsorption by an ACF filter alone showed high removal efficiency of BTX, depending on the BTX species, the upstream concentration, and the air velocity. The combination of TiO2 and ACF filter significantly increased removal of benzene which was less removed than other pollutants by an ACF filter alone. It was found that the combination effect was small in removal test of toluene and m-xylene. Removal efficiency in the tested experimental conditions was decreased in order of toluene > m-xylene > benzene.

Transition metal doped nanostructured powders were synthesized by mechanical alloying(MA) to shift the adsorption threshold into the visible light region. The synthesized powders were characterized by XRD, SEM, TEM and BET for structural analysis, UV-Vis and photoluminescence spectrum for the optical study. Also, photocatalytic abilities were evaluated by decomposition of 4-chlorophenol(4CP) under ultraviolet and visible light irradiations. Optical studies showed that the absorption wavelength of transition metal ions doped powders moved to visible light range, which was believed to be induced by the energy level change due to the doping. Among the prepared powders, doped powders, showed excellent photooxidative ability in 4CP decomposition

Titanium dioxide was prepared by Polymer Complex Solution Method(PCSM) according to the mole ratio of Titanium (IV) isopropoxide(TTIP)/solvent and polymer(Poly Ethylene Glycol). Polymer electrolytes were usually made by dispersing preproduced ceramic nanoparticles in a polymer matrix. Using this method, pure and nano-sized powder was synthesized through a simple procedure and polymer entrapment route. At the optimum amount of the polymer, the titanium ions are dispersed in solution and a homogeneous polymeric network is formed. The maximum intensity of anatase phase of was achieved by calcining at for 2h. The synthesized powders were nano-sized and the average size was about 50nm. Anatase/Rutile ratio of the synthesized was 70%/30%