본 연구에서는 실버 파우더의 입자 크기, 즉 평균 입자 크기가 2㎛과 7㎛, 이렇게 2가지 실버 페이스트를 개발하였다. 이렇게 개 발된 실버 페이스트에 대해서 점도 및 점탄성, 경화후에 잔류용제 유무 확인을 위한 TGA측정, Strain에 따른 저항 변화 및 전극 표면 구조 변화에 대해서 검토하였다. 이러한 결과를 정리하면 Strain에 따른 저항 변화를 최소화하기 위해서는 실버 파우더의 입 자를 2㎛정도인 것이 가장 바람직함을 알 수 있었다.

본 논문은 교정보호체계 내 대상자 수 적정화 필요성과 그 방향에 대해 다룬다. 범 죄자의 실효적 재범방지를 위해서는 증거기반 정책의 수립과 집행체계의 전문성 강화 등 다양한 이슈가 논의 될 수 있다. 다만, 이러한 정책들이 성공하기 위해서는 정책의 집행대상을 명확히 하여 밀도 높은 교정교화 활동을 실시 할 필요가 있다. 이러한 관 점에서, 우리 교정보호체계가 가진 큰 문제점은 교정과 보호체계 모두 필요 이상의 많 은 범죄자들을 관리감독하고 있다는 점에 있다. 교정시설의 과밀수용현상과 보호관찰 소의 만성적 인력부족 현상은 이러한 현상의 단면을 잘 보여준다. 우리 교정보호체계 는 이러한 문제점을 시설과 인력의 확충이라는 방법을 통해서 해결하려 해왔다. 그러 나 교정보호체계가 각자의 몸집을 불려가는 망의 확장 현상은 귀중한 형사사법 자원 의 낭비를 초래할 뿐 아니라, 최근 가장 설득력 있는 교정이론 중 하나인 RNR이론에 따르면 재범률 감소에 긍정적 영향을 주지 못한다. 교정과 보호 두 기관은 지역사회안전을 해치지 않는 범위내에서 대상자의 수를 감소시킴으로써 근본적인 문제를 해결 해야 한다. 시설내 교정체계는 지금 보다 많은 수용자를 탈 시설화(decarceration) 하여야 하고, 사회내 처우체계도 재범위험성이 낮은 범죄자를 조기해방(early release) 시켜줘야 한다. 본 논문은 한국의 교정보호체계가 전체 교정보호 대상자 총량의 감소 를 통해 스마트한 교정보호체계로 거듭날 수 있도록, 실효적 정책대안과 향후 제언을 제시하였다.

Consumer demand for imported and craft beer is increasing. Almost all the malt used by craft beer companies is imported. This study sought to develop a malting technology to expand the use of domestic barley, the main raw material for beer, and to examine its influence on the quality of domestic malt. The Hopum cultivar of beer barley was purchased and used at the Jeollanam-do Seed Management Center. A pilot-scale malting facility built by the National Institute of Crop Science was used. One sack (40 kg) of barley was sieved through screening sieves, and the barley was classified according to size (3.1, 2.8, 2.5, 2.2, and 2.2 mm), with the size-related composition being 18.1, 48.9, 23.3, 6.4, and 1.0%, respectively. The malt yields were 89.0, 87.6, 86.6, 82.2, and 76.1%, respectively. The coleoptiles elongation decreased as the barley size decreased. The protein content of malt tended to be high at small particle sizes of 2.2 mm. The soluble solid content of wort prepared from malt revealed good values of 17.4-17.5oBx, except for 15.3oBx for particles <2.2 mm in size. According to barley size in the malting process, these findings should be valuable quality indicators of malt.

The massive amount of radioactive waste will generated during decommissioning of nuclear. Among the radioactive waste from these disposal process, 50-55 million tons of concrete waste are included. For safe disposal, it is very important to accurately analyze the concentration of radionuclides, especially 129I and 131I, contaminated concrete. 129I, a long-lived radioisotope of iodine (t1/2=1.57 × 107 y), and 131I (t1/2=8.04 d) are generated from the fission of uranium in nuclear reactors. In Korea, according to the Nuclear Safety and Security Commission (NSSC) radioactive clearance level guide, the limit for radioactive clearance level of 129I is less than 0.01 (Bq/g). Iodine can be absorbed, accumulate in organisms, and exhibit low energy emission compared with cesium, and cobalt. Therefore, it is essential to an accurately separate and analyze iodine radioactive waste. In this study, we focused on the determination of iodine in simulated cement waste form containing KI for the recovery of iodine. We performed cement waste form sieved through a different particle size (0.5 mm < ɸ < 6.35 mm). For the separation of iodine from solid samples with low iodine content, such as soil, sediment, and cement, for sample decomposition associated with solvent extraction using CHCl3 for separation of iodine from the matrix. The separation of iodine in cement waste particles was therefore carried out using an acid leaching method using KI containing cement particles. We observed that cement particle size decreased at 6.35 mm to 0.5 mm with iodine yield decrease at 0.840±0.011 to 0.582±0.010. Thus, in this study, the acid leaching method enables to determination Iodine in cement.

The backfill refills the deep geological disposal system after the installation of buffer in the disposal hole. SKB and Posiva have established the safety function for the backfill such as hydraulic conductivity of 10-10 m/s and swelling pressure of 0.2 MPa. The study on the thermal properties is required for the evaluation of performance design and long-term stability of backfill, since the thermal condition affects the hydraulic and mechanical behavior of backfill. Thermal conductivity is a key characteristic of thermal properties due to heat dissipation from spent fuel. In this study, thermal conductivities of bentonite-sand mixed blocks were measured. The silica sands were used instead of the crushed rock with bentonil-WRK, one of the candidate bentonite of the Korean repository system. The effects of size distribution and mass ratio of sand were evaluated. Four different size of silica sand (i.e., 0.18-0.25, 0.7-1.12, 1.6-2.5, 2.5-5.0 mm) and five mixing ratio (i.e., 1:9, 2:8, 3:7, 4:6, 5:5 of bentonite and sand) were used for characterization of thermal conductivity. As a result, the thermal conductivities were measured ranging from 1.6 to 3.1 W/m∙K depending on the size and mass ratio of the sand. The smaller the size or higher the mixing ratio of sand or the higher the water contents, the higher the thermal conductivity on the surface of backfill block. The higher compressing pressure induce higher thermal conductivity. Meanwhile, the feasibility study of backfill block productivity was reviewed according to the variables of this study. The excessive sand ratio and water contents lead to poor quality that results in the failure of the block. In Korea, the research of backfill is only now in fundamental steps, thus the results of this study are expected to use for setup the experimental conditions of hydraulic and mechanical performance, and can be used for the design of safety function and evaluation of long-term stability for deep geological disposal system.

The measurement activities to evaluate material balance of nuclear material are usually performed by operator. It is because that the IAEA does not have enough manpower to carry out nuclear measurement accountancy of all nuclear materials in the world. Therefore, the IAEA should consider scenarios which facility operator tries to divert nuclear material for misuse by distorting measurement record. It is required to verify the operator’s measurement data whether it is normal or not. IAEA measures inventory items using their own equipment which is independent of facility operator equipment for verification. Since all inventory lists cannot be verified due to limited resources, the number of items to be verified is determined through statistical method which is called as sample size calculation. They measure for the selected items using their own equipment and compares with operator’s record. The IAEA determines sample size by comprehensively considering targeted diverted nuclear material amount and targeted non-detection probability and performance of measurement equipment. In general, the targeted diverted nuclear material amount is considered significant quantity (plutonium: 8 kg, uranium-235: 75 kg). If the targeted non-detection probability or the performance of the verification equipment is low, the sample size increases, and on the contrary, in the case of high non-detection probability or good performance of verification equipment, even a small sample size is satisfied. It cannot be determined from a single sample size calculation because there are so many sample size combinations for each verification equipment and there are many diversion scenarios to be considered. So, IAEA estimates initial sample size based on statistical method to reduce calculation load. And then they calculate non-detection probability for a combination of initial sample size. Through the iteration calculation, the sample size that satisfies the closest to the target value is derived. The sample size calculation code has been developed to review IAEA’s calculation method. The main difference is that IAEA calculates sample size based on approximate equation, while in this study, sample size is calculated by exact equation. The benchmarking study was performed on reference materials. The data obtained by the code show similar results to the reference materials within an acceptable range. The calculation method developed in this study will be applied to support IAEA and domestic inspection activities in uranium fuel fabrication facility.

털부처꽃(Lythrum salicaria L.)은 전국에 분포하는 다년생 초본식물로 척박하고 습한 지역을 포함한 다양한 환경에서 잘 자라는 것으로 알려져 있다. 따라서 하천변, 척박지에서 정원 용, 화훼용 및 관상용 식물로 이용이 가능하다. 본 연구는 털 부처꽃의 적정 육묘 조건(토양종류, 플러그 트레이 셀 크기,파종립수, 액비농도 및 차광)을 조사하였다. 대조구(원예상토) 에서 재배된 유묘의 생육이 가장 우수하였다. 반면 피트모스 와 펄라이트의 혼합용토는 육묘기간이 지속되면서 생육수치 가 감소하는 경향을 나타냈다. 셀 크기는 용적이 가장 큰 162 셀에서 재배된 유묘의 생육이 우수하였으나, 200셀과 288셀에 서 자란 묘도 건강했다. 한편 유묘의 결주발생을 고려하면 셀 당 2립을 파종하는 것이 적합하였다. 액비 처리는 유묘의 생 육을 촉진하였다. 특히 Hyponex 1000배는 초장, 줄기직경, 엽수, 마디수, 근장, 지상부 생체중 및 지하부 생체중을 증가 시켰다. 또한 유묘의 생육은 55% 차광 하에서 우수하였다. 따 라서 털부처꽃의 가장 효과적인 생육조건은 원예상토가 충진 된 288셀 플러그 트레이에 셀 당 2립을 파종하고 Hyponex 1000배를 시비하면서 55% 차광 하에서 재배하는 것이었다.

화상회의 시스템 사용자 증가 및 기술 발전으로 인해, 화상회의 사용맥락과 화상회의 인터페이스 레이아웃이 다양 해졌다. 사회불안은 화상회의 소통상황에도 영향을 주는데, 대면소통과 구별되는 요소인 비디오 피드백과 밀접한 관 련성이 있는 것으로 나타났다. 비디오 피드백은 상대방에게 보이는 본인의 모습을 화상회의 시스템 인터페이스에 표시해주는 기능이다. 비디오 피드백은 업무 성과를 저해하고 피로감을 유발하는 것으로 알려졌으나, 화상회의 시스 템에서 기본 기능으로 설정되어 있고 사용자들에게 보편적으로 선호된다. 본 연구는 과업지향정도, 비디오 피드백 화면크기, 사회불안이 비디오 피드백 선호도에 미치는 영향을 보기 위해 실시되었다. 연구는 온라인 설문으로 진행 되었고, 설문 참가자는 화상회의 중 과업지향정도, 사회불안수준, 선호하는 비디오 피드백 화면크기, 비디오 피드백 기능 선호도를 평가하는 문항에 응답하였다. 연구 결과, 비디오 피드백 화면크기는 과업지향정도와 비디오 피드백 선호도를 매개하는 것으로 나타났다. 구체적으로 과업지향정도가 높을수록 작은 비디오 피드백 화면크기를 선호하였 고, 이는 비디오 피드백 선호도 감소로 이어졌다. 한편, 사회불안수준에 따른 비디오 피드백 화면크기의 매개효과 차이는 유의미하지 않았다. 이러한 결과는 사용자와 화상회의 시스템의 상호작용에 대한 이해에 도움을 주어 화상회 의 시스템 디자인에 활용될 수 있는 정보를 제공한다.

This research was conducted for dewatered sludge cake of industrial wastewater treatment, i.e., as the object of inorganic sludge discharged especially in iron & steel manufacturing shop which used Air drying system to reduce water content. That drying system's single-type cyclone separator was confirmed to have significantly lower separation efficiency on the conditions 20μm and below of particular size through computational fluid dynamics(CFD) analysis. However, we found out the primarily advanced value of separation efficiency on dual-type directly connected. Regarding separation efficiency on size of 10μm, the efficiency of a single-type was presented at 51.91%. On the other side, the efficiency of the dual-type was 97.88%. This advanced effect of the dual cyclone separator was checked at a demo facility of air drying equipment designed by 340m3/min of airflow on site.

The study was aimed to investigate the operational meal costs by kindergarten size in Seoul and to analyze recognition for optimal meal prices. A survey (31.6% recovery rate) was conducted on all kindergartens (779 kindergartens) in Seoul on April 2021 using descriptive analysis, t-test, and dispersion method. A price sensitivity measurement (psm) method was used to determine optimal meal prices. Result showed an average food cost for kindergartens of 2,647 won, an average labor cost of 605 won, an average operating cost of 146 won, and the total meal cost of 3,506 won. Total meal cost decreased with increasing kindergarten size (p<0.001). On the other hand, kindergartens with more students decreased the ratio of food cost to total meal cost, and operating cost and labor costs (p<0.001) increased. The optimal price of kindergarten operators' meal cost (OPP) was KRW 3,673. Furthermore, the analysis showed the sensitivity of operators' meal costs to kindergarten size was insignificant.

This study was conducted to provide basic data for product development and marketing strategies for the Thai home meal replacement (HMR) market, to reflect the changing trends in household sizes in Thailand. The results of analyzing the characteristics and differences of HMR consumption behavior between single-person households and multi-person households in Thailand were as follows: It was found that single-person households use HMR to save money and for the convenience in cooking and preparation. In the preference by HMR type, multi-person households showed a higher preference for all types of products than single-person households. Thai consumers, regardless of their household size, mainly use department stores and large shopping malls to purchase HMR, and they most prefer to get information through Internet advertisements. The shelf life, quality, taste, hygiene, and freshness of HMR were the main considerations for their selection. Based on the results of this study, the Thai market requires the development of HMR products that are reasonable in terms of cost and preparation time. In addition, it is necessary to develop products that can satisfy consumer needs, such as nutritional enhancement and therapeutic foods, products that are organic, eco-friendly, cater to various menus, and address the premium segment.

PURPOSES : In this study, the amount of core stone breaking in the size of boulders by excavator braker work was analyzed quantitatively through on-site test construction. In addition, the factors affecting workload were studied. METHODS : In the field test, 30 core stones of boulder sizes (1–4 m3) that appeared during earthworks, such as road construction and site construction, were collected from three locations, and the rock breaking work was carried out simultaneously using three excavator breakers(1.0-m3 volume). During the core stone breaking, progress was analyzed through video recordings. RESULTS : After the completion of rock breaking, the amount of breaking work was analyzed by direct loading and weighing using a 15- ton dump truck. As a result of the test construction, there was a significant difference in the amount of work completed per hour. CONCLUSIONS : It was found that the results were greatly affected by not only the performance of the excavator braker equipment, but also the skill of the driver and the size of the core stones.