To solve the problem of water pollution, researchers have proposed a photocatalytic degradation technology, in which the key factor is the development of efficient photocatalytic materials. Graphitic carbon nitride (g-C3N4), an n-type semiconductor, has been widely studied due to its suitable band gap (2.7 eV), low cost, easy preparation, non-toxicity, and high photostability. However, the pure-phase g-C3N4 still has defects such as low specific surface area, insufficient visible light absorption, low charge mobility, few active sites for interfacial reaction, and easy recombination of photogenerated electron–hole pairs, which leads to the lower photocatalytic activity of g-C3N4. Aiming at the problems mentioned above, this paper focus on the synthesis of g-C3N4-based composites with high photocatalytic activity via lemon juice induction method. Thiourea and lemon juice were selected as precursors, and carbon quantum dots (CQDs) as electron mediators were introduced anchoring on the surface of g-C3N4 to build g-C3N4/CQDs with compact interface. The results showed that small-sized CQDs are uniformly distributed on the surface of g-C3N4, and the g-C3N4/CQDs composite has a 2D0D structure, which reduces the recombination of photogenerated electron–hole pairs. The photocatalytic degradation efficiency of 4% g-C3N4/CQDs for RhB reaches the highest data of 90.9%, and the photocatalytic degradation rate is 0.016 min− 1, which is about 2.3 times that of g-C3N4. After four cycles of photocatalytic reaction, the photocatalytic degradation efficiency of the material remained at 81.7%. Therefore, the g-C3N4/CQDs synthesized via lemon juice induction has a more stable microstructure, and the charge separation efficiency is greatly improved, which is suitable for practical photocatalytic environmental protection.

We report the synthesis and gas sensing properties of bare and ZnO decorated TeO2 nanowires (NWs). A catalyst assisted-vapor-liquid-solid (VLS) growth method was used to synthesize TeO2 NWs and ZnO decoration was performed using an Au-catalyst assisted-VLS growth method followed by a subsequent heat treatment. Structural and morphological analyses using X-ray diffraction (XRD) and scanning/transmission electron microscopies, respectively, demonstrated the formation of bare and ZnO decorated TeO2 NWs with desired phase and morphology. NO2 gas sensing studies were performed at different temperatures ranging from 50 to 400 oC towards 50 ppm NO2 gas. The results obtained showed that both sensors had their best optimal sensing temperature at 350 oC, while ZnO decorated TeO2 NWs sensor showed much better sensitivity towards NO2 relative to a bare TeO2 NWs gas sensor. The reason for the enhanced sensing performance of the ZnO decorated TeO2 NWs sensor was attributed to the formation of ZnO (n)/ TeO2 (p) heterojunctions and the high intrinsic gas sensing properties of ZnO.

In this study, Y3Al5O12:Eu3+ red phosphors were synthesized at different temperatures using a solid state reaction method. The crystal structures, surface and optical properties of the Y3Al5O12:Eu3+ red phosphors were investigated using Xray diffraction (XRD), field emission scanning electron microscope (FE-SEM), and photoluminescence (PL) analyses. From XRD results, the crystal structure of the Y3Al5O12:Eu3+ red phosphors was determined to be cubic. The maximum emission spectra were observed for the Y3Al5O12:Eu3+ red phosphor prepared by annealing for 4h at 1,700 oC. The 565~590 nm photoluminescent spectra of the Y3Al5O12:Eu3+ red phosphors is associated with the 5D0 → 7F2 magnetic dipole transition of the Eu3+ ions. The intensity of the photoluminescent spectra in the red phosphors is more dominant for the magnetic dipole transition than the electric dipole transition with increasing annealing temperature. The International Commission on Illumination (CIE) coordinates of Y3Al5O12:Eu3+ red phosphors prepared by 1,700 oC annealing temperature are X = 0.5994, Y = 0.3647.

Cu-doped ZnSe quantum dots were successfully synthesized in an aqueous solution using an internal doping method. The effects of ligand type, CuSe synthesis temperature, and heating time on Cu-doped ZnSe synthesis were systematically investigated. Of MPA, GSH, TGA, and NAC used as ligands, MPA was the optimal ligand as determined by PL spectrum analysis. In addition, the emission wavelength was found to depend on the synthesis temperature of the internal doping core of CuSe. As the temperature increased, the doping of Cu2+ was enhanced, and the emission wavelength band was redshifted; accordingly, the emission peaks moved from blue to green (up to 550 nm). Thus, the synthesis of Cu:ZnSe using internal doping in aqueous solutions is a potential method for ecomanufacturing of colortuned ZnSe quantum dots for display applications.

Hydrogen-bonded organic frameworks (HOFs) are a new type of porous crystalline material that are constructed by intermolecular hydrogen bonding of organic building blocks to form twodimensional (2D) and three-dimensional (3D) crystalline networks. High-quality HOF single crystals are easily grown for direct superstructure analysis using single crystal X-ray diffraction, which is essential for revealing the relationship between structure and properties. The unique advantages of HOF, such as high crystallinity, porosity and fast regeneration, have allowed it to be used in a variety of applications including catalysis and gas separation. Squaric acid (SQA) is a non-carboxylic, organic acid with proton donor and acceptor ability which is known to take on a variety of coordination modes with metal ions. Pyrazine is a six-membered aromatic heterocycle bearing two nitrogen atoms, which has sp2 hybridized C atoms with C-H hydrogen bonds. This work describes the synthesis and structural characteristics of HOF based on squaric acid and pyrazine. Based on single crystal X-ray diffraction data, this MOF crystallizes in the triclinic P-1 space group. Each asymmetric unit is composed of H2SQ and pyrazine. All squaric acid molecules share one H atom with the N atom of pyrazine molecules. The layer distance between nearby O atoms from squaric acid in different layers equals 5.29 Å. Also, our HOF showed high adsorption capacity the during experiments. The composition and comparative characteristics of HOF are given using SCXRD, PXRD, SEM and UV-vis.

Nuclear spent fuel (SNF) disposal in deep geological repositories is considered as one of sound options for the long-term and safe sequestration of radiotoxic SNF and the sustainable use of nuclear energy. The chemical behaviors of various radionuclides originated from SNF should be well understood to evaluate the migrational behaviors of radionuclides and their reactions and interactions with various geochemical components. Formation of secondary minerals, colloids, other insoluble precipitates is of interest since the concentrations of radionuclides in groundwaters can be limited by the solubility of those solid phases. Particularly when evaluating their solubility, the use of well-defined solid materials in terms of chemical composition and molecular structure is crucial to obtain reliable measurement results. In this study, a synthetic calcium uranyl silicate (Ca-U(VI)-silicate, or uranophane) was prepared and characterized by using various analytical methods including powder X-ray diffraction (pXRD), scanning electron microscopy/energy dispersive X-ray spectrometry (SEM/EDX), and vibrational (FTIR and Raman) spectroscopies. Uranyl silicate minerals are significant to the disposal of nuclear wastes. Our simulation demonstrates that uranophane (Ca[UO2SiO3OH]2·5H2O), one having a U:Si ratio of 1:1, can be a mineral species limiting U(VI) solubility under groundwater conditions in Korea. For the preparation of Ca-U(VI)-silicate, we applied a two-step hydrothermal synthetic procedure reported in literature with modification. Briefly, we conclude that the obtained mineral phase is the ‘α-uranophane’; our characterization results show that the structural and spectroscopic properties of the synthetic Ca-U(VI)-silicate agree well with those of α-uranophane. For instance, the pXRD patterns obtained from the solid show nearly identical diffraction peak positions with those from the reference XRD pattern. From IR and Raman spectroscopy it is noticed that the stretching modes of UO2 2+ and SiO4 4- ions result in strong absorption bands in a region of 700 ~ 1,100 cm-1. Elemental compositions of the synthetic solids were also estimated by using EDX analysis, which results in a Ca:U:Si ratio close to 1:2:2 on average. However, we found that it is difficult to obtain good crystallinity of uranophane, which can be observable by using SEM and its image analysis. We believe that this work serves as a model study to provide synthetic routes of radionuclide-related mineral phases and applicable solid phase characterization methods. In the presentation, the potential use of the U(VI)-silicate solid phase for the upcoming groundwater solubility measurements will be discussed. Keywords: Hexavalent Uranium, Silicate

Fescues, which are widely cultivated as grasses and forages around the world, are often naturally infected with the endophyte, Epichloë. This fungus, transmitted through seeds, imparts resistance to drying and herbivorous insects in its host without causing any external damage, thereby contributing to the adaptation of the host to the environment and maintaining a symbiosis. However, some endophytes, such as E. coenophialum synthesize ergovaline or lolitrem B, which accumulate in the plant and impart anti-mammalian properties. For example, when livestock consume excessive amounts of grass containing toxic endophytes, problems associated with neuromuscular abnormalities, such as convulsions, paralysis, high fever, decreased milk production, reproductive disorders, and even death, can occur. Therefore, pre-inoculation with non-toxic endogenous fungi or management with endophyte-free grass is important in preventing damage to livestock and producing high-quality forage. To date, the diagnosis of endophytes has been mainly performed by observation under a microscope following staining, or by performing an immune blot assay using a monoclonal antibody. Recently, the polymerase chain reaction (PCR)-based molecular diagnostic method is gaining importance in the fields of agriculture, livestock, and healthcare given the method’s advantages. These include faster results, with greater accuracy and sensitivity than those obtained using conventional diagnostic methods. For the diagnosis of endophytes, the nested PCR method is the only available option developed; however, it is limited by the fact that the level of toxic alkaloid synthesis cannot be estimated. Therefore, in this study, we aimed to develop a triplex real-time PCR diagnostic method that can determine the presence or absence of endophyte infection using DNA extracted from seeds within 1 h, while simultaneously detecting easD and LtmC genes, which are related to toxic alkaloid synthesis. This new method was then also applied to real field samples.

목적 : 본 연구는 항균 기능을 갖춘 안경테의 필요성에 주목하여 고분자 물질인 Polyvinylpyrrolidone(PVP)을 사용하여 은 나노 입자를 합성하고, 금속 안경테 소재에 코팅하여 항균성과 코팅 특성을 평가해 보고자 한다. 방법 : 안정성이 높은 고분자 물질인 PVP를 환원제, 분산제, 안정제로 사용하고 합성 온도를 달리하여 은 나노 입자를 합성하였다. 합성한 시료의 특성은 UV-visible spectrophotometer, SEM, EDS를 사용하여 분석하였으 며 paper disk diffusion method로 항균성을 평가하였다. 합성한 은 나노콜로이드를 금속 안경테 소재인 티타 늄, 스테인리스스틸 기판에 코팅하고 코팅막의 특성과 항균성을 측정하였다. 결과 : PVP를 사용하여 합성한 시료 모두에서 은(Ag)이 검출되어 은 나노 입자의 생성을 확인할 수 있었다. 합성 온도에 따른 은 나노 입자의 크기는 차이를 보였으며 Escherichia coli, Pseudomonas aeruginosa, Aspergillus brasiliensis의 경우 45℃에서 합성한 은 나노콜로이드의 항균활성이 가장 크게 나타났다. 이를 금속 안경테 소재 기판에 코팅한 후 항균성을 확인한 결과 코팅막의 항균력을 확인할 수 있었다. 결론 : PVP를 사용하여 합성한 은 나노콜로이드를 금속 안경테 소재 기판에 코팅한 결과 코팅막의 항균성이 확인되어 항균 기능을 가진 안경테 제작 시 항균 물질로 활용될 수 있을 것이라 사료된다.

Sulfur is an essential element in plants, including amino acids, vitamin synthesis, and acting as an antioxidant. However, the interaction between endogenous sulfur and proline synthesis has not been yet fully documented. White clover (Trifolium repens L.) is known as a species highly sensitive to sulfate supply. Therefore, this study aimed to elucidate the role of sulfur in regulating proline metabolism in relation to ammonia detoxification and hydrogen peroxide (H2O2) accumulation in white clover. The detached leaves of white clover were immersed in solution containing different concentration of sulfate (0, 10, 100, and 1000 mM MgSO4). As MgSO4 concentrations were increased, the concentration of H2O2 increased up to 2.5-fold compared to control, accompanied with H2O2 detection in leaves. Amino acid concentrations significantly increased only at higher levels (100 and 1000 mM MgSO4). No significant difference was observed in protein concentration. Proline and Δ1-pyrroline-5-carboxylate (P5C) concentrations slightly decreased at 10 and 100 mM MgSO4 treatments, whereas it rapidly increased over 1.9-fold at 1000 mM MgSO4 treatment. Ammonia concentrations gradually increased up to 8.6-fold. These results indicate that exogenous sulfur levels are closely related to H2O2 and ammonia synthesis but affect proline biosynthesis only at a higher level.

The presence of dyes in water is the most popular problem recently, so the current study was directed towards the synthesis of an effective material consisting of NiO and MWCNTs. The NiO/F-MWCNTs nanocomposite was synthesized using a simple hydrothermal method after functionalization of MWCNTs using sulfuric acid and nitric acid and utilized as an efficient surface to adsorption of malachite green dye from polluted water. The nanocomposite sample was characterized using several techniques are X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), Thermogravimetric analysis (TGA), Field emission scanning electron microscopy (FESEM), High- resolution transmission electron microscopy (HRTEM), Brunauer–Emmett–Teller (BET) surface area analysis, Barrett-Joyner-Halenda (BJH) analysis and Energy dispersive X-ray (EDX). The analytical results showed that the prepared nanocomposite is of good crystalline nature with a particle size of 25.43 nm. A significant specific surface area was 412.08 m2/ g which indicates the effective impact of the nanocomposite in the adsorption of malachite green (MG) dye. On the other hand, the effect of adsorbent dose, temperature, acidic function and contact time on the adsorption efficiency of dye was studied. The kinetics of dye adsorption were also investigated employing two kinetic models, pseudo-first-order model and pseudo-second-order model. Finally, the thermodynamic functions were determined to identify the type of the reaction and the spontaneity of the process.

As frontier materials, graphene oxide (GO) and graphene have penetrated almost all research areas and advanced numerous technologies in sensing, electronics, energy storage, catalysis, water treatment, advanced composites, biomedical, and more. However, the affordable large-scale synthesis of high-quality GO and graphene remains a significant challenge that negatively affects its commercialisation. In this article, firstly, a simple, scalable approach was demonstrated to synthesise high-quality, high yield GO by modifying the improved Hummers method. The advantages of the optimised process are reduced oxidation time, straightforward washing steps without using coagulation step, reduction in cost as eliminating the use of phosphoric acid, use of minimum chemical reagents, and increased production of GO per batch (~ 62 g). Subsequently, the produced GO was reduced to reduced graphene oxide (rGO) using three different approaches: green reduction using ascorbic acid, hydrothermal and thermal reduction techniques. The GO and rGO samples were characterised using various microscopy and spectroscopy techniques such as XRD, Raman, SEM, TEM, XPS and TGA. The rGO prepared using different methods were compared thoroughly, and it was noticed that rGO produced by ascorbic acid reduction has high quality and high yield. Furthermore, surface (surface wettability, zeta potential and surface area) and electrical properties of GO and different rGO were evaluated. The presented synthesis processes might be potentially scaled up for large-scale production of GO and rGO.

A porous-carbon material UiO-66-C was prepared from metal–organic frameworks UiO-66 by carbonization in inert gas atmosphere. Physicochemical properties of UiO-66-C materials were well characterized by Powder X-ray diffraction (PXRD), Scanning electron microscope (SEM), Fourier-transform infrared spectroscopy (FT-IR), Raman spectrometer, N2 adsorption/ desorption isotherms (BET), and the adsorption properties of the products were studied UiO-66-C has a high specific surface area up to 1974.17 m2/ g. Besides, the adsorption capacity of tetracycline could reach 678.19 mg/g, the adsorption processes agreed well with the pseudo-second-order kinetic model and Langmuir isotherm model.

NiMoS2 is a promising material for various functional applications and highly compatible with GO to make hybrid nanocomposites with excellent characteristics for supercapacitor electrode material. Deposition of NiMoS2 was achieved on the rGO(reduced Graphene Oxide) surface to form a NiMoS2− rGO nanocomposite by the method of the facile hydrothermal synthesis process. XRD pattern shows the crystalline nature of composites. Raman and EPMA result interpreting the composites formation and elements compositions, respectively. The sheet-like morphology of rGO was found in the composites by FESEM images. Particles distribution was confirmed by HR-TEM. The electrochemical properties of the pure NiMoS2 and NiMoS2– rGO composites have been studied by cyclic voltammetry analysis. The results revealed that the NiMoS2/ 5% rGO nanocomposites exhibit high specific capacitance compared to pure NiMoS2 due to the synergistic effects of NiMoS2 and rGO in the composite material. The photocatalytic behavior of the prepared nanocomposites for dye degradation was tested. The quantity of rGO has significantly improved the photocatalytic behavior of NiMoS2/ rGO composites. The studies on degradation mechanism, the N2 adsorption/desorption isotherms, pore size distribution behavior and % of removal of MB reveal the enhanced photocatalytic performance of sysnthesised composites.

Graphene, the wonder material has brought a revolutionary change in the field of nanotechnology owing to its tremendous properties. Though different methods for the synthesis of graphene have been reported, the chemical synthesis route offers a scalable and high-volume production of graphene. The unreliability of graphite and hydrocarbon resources to serve as steady supplies of carbon resources and further in the synthesis of graphene has led to the exploration and use of alternative low-cost carbon-rich resources (coal, graphite, rice husk, sugarcane bagasse, peanut shells, waste tyres, etc.) as precursors for graphene synthesis. The use of untraditional carbon resources reduces dependence on traditional resources (coal, graphite), reduced cost, increased reliability, and provides a way for the management of waste biomass. This review hence focuses on the synthesis of graphene by the most common approachable method, oxidation–reduction of graphite, along with the various other chemical methods of synthesis from varied carbon resources.

Polyoxometalates (POMs) are nanoclusters composed of transition metals with high oxidation states. Owing to their redox properties and structural diversity, POMs have been applied to broad fields, such as catalysis, materials, and medicine. Among various fields of application, POMs play an important role in radiochemistry. POMs can form complexes with tri- and tetravalent lanthanides and actinides (radioactive elements), which may be good sequestrators or agents for separating nuclear wastes. Among the most prominent POM structures, Anderson-type POMs with a general formula of [Hy(XO6)M6O18]n− (y=0–6, n=2–8, M=addenda atom, X=heteroatom) represent one of the basic topological structures of the POM family. An important feature of Anderson type POMs is incorporating a large number of various heteroatoms with different size and oxidation states, which can lead to tune chemical properties. Interestingly, no example of Anderson type POMs with early transition metal ions in the heteroatom site has been reported to date. Herein, we discovered that the Anderson POM Na2K6Ti0.92W6.08O24·12H2O, which consists of pure inorganic framework built from a central Ti core supported by six WO6 inorganic scaffold, and the crystal structure was confirmed and refined using single-crystal X-ray diffraction (SC-XRD). In addition, structural characterizations, including, Fourier-transform infrared spectroscopy (FT-IR), X-ray photoelectron spectroscopy (XPS), and Inductively coupled plasma-optical emission spectroscopy (ICP-OES) were performed.

Efficient capture and storage of radioactive iodine (consisting of two isotopes: 129I and 131I), produced or released from nuclear activities, are of paramount importance for sustainable development of nuclear energy due to their volatility and long half-life. Therefore, it is very important to develop new adsorbents for efficient utilization of radioactive iodine from nuclear waste. Various methods and materials are used for I2 capturing and removing, including MOFs due to their high porosity and fast adsorption kinetics, which are rightfully considered effective sorbents for removing I2. Metal–organic frameworks (MOFs) are porous crystalline materials which have diverse pore geometry and unique physicochemical properties, have attracted enormous attention for use in gas storage, separation and catalysis. The ability of MOFs to adsorb volatile products at room temperature can significantly improve the cost-effectiveness of the utilization process. This work describes the synthesis and characterization of three new metal-organic frameworks based on pyrazine (pyz), 44’bipyridine (bpy), 1,2 -bis(4 - pyridyl) – ethane (bpe) and copper (II) hexafluorozironate, as potential adsorbents for I2 capture. All of these three MOFs exhibit a two - dimensional (2D) crystal structure consisting from infinity non-crossing linear chains. The crystal structure of [Cu(pyz)2(ZrF6)2(H2O)2], [Cu(bpy)4(H2O)2ZrF6] and [Cu(bpe)4(H2O)2ZrF6] were characterized using powder X-ray diffraction (PXRD), single crystal X-ray diffraction (SC-XRD). Comparative characteristics of synthesized MOFs, including Fourier-transform infrared spectroscopy (FTIR) and thermogravimetric analysis (TGA) were also performed. The I2 sorption experiments were examined by UV-vis spectroscopy.