The design shear strength equations of RC shear walls have been developed based on their performance under in-plane (IP) loads, thereby failing to account for the potential performance degradation of shear strength when subjected to simultaneous out-of-plane (OOP) loading. Most of the previous experimental studies on RC walls have been conducted in one direction under quasi-static conditions, and due to the difficulty in experimental planning, there is a lack of research on cyclic loading and results under multi-axial loading conditions. During an earthquake, shear walls may yield earlier than their design strength or fail unexpectedly when subjected to multi-directional forces, deviating from their intended failure mode. In this paper, nonlinear analysis in finite element models was performed based on the results of cyclic loading experiments on reinforced concrete shear walls of auxiliary buildings. To investigate the reduction trend in IP shear capacity concerning the OOP load ratio, parametric analysis was conducted using the shear wall FEM. The analysis results showed that as the magnitude of the OOP load increased, the IP strength decreased, with a more significant effect observed as the size of the opening increased. Thus, the necessity to incorporate this strength reduction as a factor for the OOP load effect in the wall design strength equation should be discussed by performing various parametric studies.

Mulberry fruit is a superior source of polyphenols, especially anthocyanin, and has a long history of use as an edible fruit and traditional medicine. The anthocyanin composition of mulberry fruit from 15 Korean cultivars was analyzed by ultra-performance liquid chromatography diode array detector with quadrupole time of flight/mass spectrometry (UPLC-DAD-QToF/MS) based on a cyanin internal standard. The four glycosides were identified by comparison with authentic standards and published reports. The major anthocyanin was cyanidin 3-O-glucoside (71.7%), followed by cyanidin 3-O-rutinoside (26.6%). The minor components (total of 1.7%) were pelargonidin 3-O-glucoside and pelargonidin 3-O-rutinoside. The total anthocyanin content (mg/100 g, dry weight) of mulberry fruit varied by cultivar and ranged from 471.5±4.0 (Su Hong) to 4,700.2±54.0 (Gwa Sang2). Among the 15 cultivars examined, Gwa Sang2 showed the highest level of cyanidin 3-O-glucoside (3,133.4±32.6), which was 9-fold higher than that of Su Hong (351.5±3.4). In conclusion, anthocyanin profiles, including pelargonidin 3-O-glucoside and pelargonidin 3-O-rutinoside, were reported for the first time from 15 Korean mulberry fruit cultivars. The results will contribute valuable information on pharmaceutical properties, breeding superior mulberry cultivars, and food industries.

Reported positive ion fragmentation of phenolic acid derivatives in rice (Oryza sativa L.) were summarized based on the literature. A total of eight phenolic acids (4 derivatives of ferulic acid, 3 derivatives of sinapic acid and p-coumaric acid) were isolated and identified from rice (raw and steamed) using UPLC-DAD-QToF/MS. Results revealed that 6-O-feruloylsurose was the major component with 3'-O-sinapoylsucorse being tentatively identified in Oryza sativa L. for the first time as a new hydroxycinnamoyl derivative in rice grains. In our study, raw brown rice had the highest phenolic acid contents with Samkwang showing higher phenolic acid content than Saeilmi and Sindongjin (12.41 vs. 7.89 and 3.10 mg/100 g dry weight, respectively). Of all varieties, brown rice had higher phenolic acid contents than white rice. These contents decreased considerably when rice was steamed whereas, p-coumaric acid and ferulic acid contents were increased. Additionally, contents of rice (raw and steamed) can be used as a fundamental report for new rice varieties.

This study investigated the quality characteristics of convenient chicken porridge prepared with fresh ginseng powder (FGP). The porridge made with the addition of FGP showed significantly higher or similar pH at 5.99-6.13 compared to porridge made without adding FGP. The convenient chicken porridge with FGP had lower viscosity and higher spreadability than the control group (p<0.05). This porridge exhibited higher lightness (L) and yellowness (b) values but a lower redness (a) value than the control group (p<0.05). The porridge made with the addition of 0.4% blanched FGP (BG0.4) displayed higher total polyphenol content, 2,2-diphenyl-1-picrylhydrazyl (DPPH) and 2,2-azino-bis-3-ethylbenzothiazoline-6-sulfonic acid (ABTS) radical scavenging activities than the other types of chicken porridge (all p<0.05). The porridge with the addition of FGP showed weaker “rice grain size”, “glossiness”, “appearance cohesiveness”, “cooked rice aroma”, “sweet taste”, “texture cohesiveness”, “thickness”, and “stickiness” than the control group (all p<0.05). The appearance and flavor acceptance were significantly higher or similar for the porridge samples made with the addition of 0.2% non-blanched FGP (NBG0.2) and 0.4% non-blanched FGP (NBG0.4) when compared with those of the control group.

PURPOSES : Evaluation of the effectiveness of changing the form of yellow carpet installation as a way to reduce child pedestrian traffic accidents. METHODS : Through expert opinion, two improvement plans for yellow carpet installation (oblique type, extended type) were derived. The improvement paln was built in virtual reality, and a virtual driving experiment was performed using a driving simulator and eye-trakcing device. The improvement effects of the two alternatives were evaluated by analyzing eye-tracking data and driving behavior. RESULTS : In the case of the oblique type, it was analyzed that it was effective in improving the total gaze time and first gaze position compared to the normal type. In the case of the extended type, it was analyzed that the workload during operation can be reduced. However, neither of them had a significant effect on driving behavior. CONCLUSIONS : Although the change in the yellow carpet installation type did not affect the driver's driving behavior, it had advantages in terms of visual behavior and workload while driving, so it can be considered as an alternative among measures to improve traffic accidents involving children and pedestrians.

Cnidium officinale M. is an important crop that is widely used as a raw material for health functional foods. However, it is experiencing cultivation difficulties due to climate change and abnormally high temperatures. In response to this problem, the characteristics and main causes of the high-temperature damage occurring in C. officinale M. cultivation fields were analyzed. A survey of five farmhouse fields in Jecheon and Bonghwa, major C. officinale M. cultivation areas in Korea in 2018, indicated that about 5% to 37% of the cultivation fields in Jecheon and 5% to 15% of the fields in Bonghwa died from wilting. The high-temperature damage of the C. officinale M. fields is divided into two categories: upper leaves drying due to solar radiation and temperature, and lower leaves dying serially to the radiant heat of the vinyl mulch. Damage caused by radiant heat was typically greater. This is due to the greenhouse effect that occurs in the small space between the black vinyl mulching and the soil. The heat radiated to the surface of the ridge creating an environmental condition that greatly exceeded the atmospheric temperature especially on hot days. As a result, short plants with underground parts, such as C. officinale M., can suffer more high-temperature damage than other plants, so it is considered that it is necessary to develop related technologies such as mulching materials that can reduce pavement temperature in the future.

In the present work, we address the new route for the green synthesis of manganese dioxide (MnO2) by an innovative method named the solution plasma process (SPP). The reaction mechanism of both colloidal and nanostructured MnO2 was investigated. Firstly, colloidal MnO2 was synthesized by plasma discharging in KMnO4 aqueous solution without any additives such as reducing agents, acids, or base chemicals. As a function of the discharge time, the purple color solution of MnO4 - (oxidation state +7) was changed to the brown color of MnO2 (oxidation state +4) and then light yellow of Mn2+ (oxidation state +2). Based on the UV-vis analysis we found the optimal discharging time for the synthesis of stable colloidal MnO2 and also reaction mechanism was verified by optical emission spectroscopy (OES) analysis. Secondly, MnO2 nanoparticles were synthesized by SPP with a small amount of reducing sugar. The precipitation of brown color was observed after 8 min of plasma discharge and then completely separated into colorless solution and precipitation. It was confirmed layered type of nanoporous birnessite- MnO2 by X-ray powder diffraction (XRD), fourier-transform infrared spectroscopy (FT-IR), and electron microscopes. The most important merits of this approach are environmentally friendly process within a short time compared to the conventional method. Moreover, the morphology and the microstructure could be controllable by discharge conditions for the appropriate potential applications, such as secondary batteries, supercapacitors, adsorbents, and catalysts.

We used the measurement data derived from a proton transfer reaction time-offlight mass spectrometry (PTR-ToF-MS) to ascertain the source profile of volatile organic compounds (VOCs) from 4 major industrial classifications which showed the highest emissions from a total of 26 industrial classifications of A industrial complex. Methanol (MOH) was indicated as the highest VOC in the industrial classification of fabricated metal manufacture, and it was followed by dichloromethane (DM), ethanol (EN) and acetaldehyde (AAE). In the industrial classification of printing and recording media, the emission of ethylacetate (EA) and toluene (TOL) were the highest, and were followed by acetone (ACT), ethanol (EN) and acetic acid (AA). TOL, MOH, 2-butanol (MEK) and AAE were measured at high concentrations in the classification of rubber and plastic manufacture. In the classification of sewage, wastewater and manure treatment, TOL was the highest, and it was followed by MOH, H2S, and ethylbenzene (EBZ). In future studies, the source profiles for various industrial classifications which can provide scientific evidence must be completed, and then specified mitigation plans of VOCs for each industrial classification should be established.

본 연구는 광주 내 대형마트와 온라인 마켓에서 영유아 를 대상으로 판매하는 과자류 80건 및 음료류 40건의 식 품첨가물(타르색소, 인공감미료), 곰팡이독소 및 영양성분 (자당, 무기질)을 분석하였다. 유아용 표시 식품의 기준 및 규격이 불검출로 설정된 타르색소와 사카린나트륨은 모든 시료에서 검출되지 않았다. 과자류(기타가공품) 1건에서 인공감미료인 아세설팜 칼륨이 0.07 g/kg 검출되었으나 이 는 식품첨가물의 기준 및 규격에서 정한 허용 기준치 이 하였다. 곰팡이독소는 아플라톡신 및 오크라톡신 A는 검 출되지 않았으며, 푸모니신 B1, B2 및 제랄레논이 각각 과자류에서 14건(9.78-78.94 μg/kg), 6건(5.58-11.73 μg/kg) 및 9건(2.96-8.83 μg/kg) 검출되었다. 푸모니신에 대한 기 준·규격은 따로 설정되어 있지 않았으나 타 연구 결과와 비교했을 때 비슷한 수준이었으며, 제랄레논은 식품 일반 에 대한 공통 기준·규격 이내로 확인되었다. 자당은 과자 류에서 65건(0.02-40.94 g/내용량(g)), 음료류에서 24건(0.12- 27.60 g/내용량(g)) 검출되었으나 식품유형간 유의적인 차 이는 없었으며, 타 연구 결과와 비교했을 때 그 함량도 적 은 편이었다. 다만, 검출 시료 89건 중 1건을 제외하고는 모두 1일 영양성분 기준치를 성인 기준으로 표시하고 있 었기 때문에 제품 구입 시 영유아 기준으로 오인될 우려 가 있다. 무기질은 대부분의 시료에서 검출되었으며 과자 류 중 4건의 시료에서 내용량 당 아연 함량이 상한섭취량 (1-2세: 6 mg/일, 3-5세: 9 mg/일)을 초과하는 수준이었다. 아연 강화식품이나 보충제의 과다 섭취가 인체의 유해성 을 보인다는 다수의 보고가 있으므로 섭취시 유의할 필요 가 있다. 나트륨은 과자류 80건 중 16건이 영유아용 표시 식품의 기준을 초과하였으나 모두 품목제조보고서상 영유 아 섭취 대상 식품으로 표시하지 않아 해당 기준을 적용 할 수 없었다. 따라서 영유아용 표시 식품의 기준·규격을 설정과 함께 현재 시행되는 기준·규격이 알맞게 적용될 수 있도록 표시 기준 강화 등의 제도적 개선이 필요할 것으 로 보인다.

This study was carried out in order to provide suggestions with regard to optimal control methods for various odor emission facilities (162 companies and 26 industrial classifications) through comparative analysis of effective odor treatment technologies for each type of odor substance by literature reviews, based on measured 22 odor substance data for 162 samples taken from A city. The industrial classification of Pulp showed the highest odor quotient (7,589 as average value) and was followed by the industrial classifications of Wastewater, Woods, and Furniture, indicating average odor quotient values of 2,361, 1,396 and 1,392, respectively. Absorption using chlorine dioxide and sodium hydroxide can be an optimal treatment method to remove the odor substances of sulfide and aldehyde groups. Biofilers with microbial communities will be effective to remove odors caused by volatile organic compounds (VOCs) and an absorption method using sulfuric acid is proper for the removal of odor substances caused by nitrogens.

Purpose: This study aimed to explore university students’ experiences of participating in online classes during the COVID-19 outbreak. Methods: A survey was conducted with 169 third- and fourth-year students at five universities in W City from May 5 to 22, 2021 through an online survey platform. Qualitative data were collected from 13 third- and fourth-year students at five universities in the same area through three focus group interviews between May 22 and 25 and analyzed through qualitative content analysis. Results: The experience of online classes was rated in the following order: live lectures (92.9%) and recorded lectures (73.4%). Satisfaction with online classes was rated for recorded lectures, which were scored 3.54±1.05 (out of five), and live lectures, which were scored 3.32±1.02. Lack of interaction with faculty (37.9%) and lack of participating practicum (30.8%) were cited as dissatisfaction factors in online classes. From the qualitative data, five sub-themes were identified: “not being respected in one’s learning”, “increased burden of learning in a situation of poor communication,” “it's not that I hate online classes”, “efforts to improve the loose will and attitude toward classes”, “reduced quality of experience and uncertain future”. These sub-themes were abstracted under the theme of “everyday life of learning alone toward an uncertain future”. Conclusion: To ensure more effective online learning, it is necessary to strengthen the interaction between faculty and students, apply online teaching strategies suitable for class objectives, and support various programs to motivate students for self-directed learning.

Background: The purpose of this study was to determine the bidirectional association between burning mouth syndrome (BMS) and depression disorders. Methods: A total of 854 pairs of BMS and 58 999 pairs of depression disorders matched 1:1 for age and sex were analyzed using conditional logistic regression models, which were adjusted for potential confounding factors. Results: Bidirectional analysis found that BMS was associated with depression disorders (odds ratio=4.64, P < 0.001) and depression disorders was also significantly associated with BMS (odds ratio=2.97, P < 0.001). Conclusion: These findings indicate a significant bidirectional association between BMS and depression disorders. The odds ratios suggest that BMS is a stronger predictor for incidence of depression disorders than depression disorders predicting incidence of BMS. Given this retrospective cohort design, the mechanisms underlying the association between BMS and depression disorders are not directly analyzed. Therefore, further investigation are needed to analyze the causality between BMS and depression disorders.

목적: 본 연구의 목적은 운동심상 훈련이 심폐 기능에 미치는 효과를 확인하는 것이다. 방법: 본 연구는 20대 성인 남성 26명을 대상으로 실시하였다. 참가자는 각각 13명의 참가자를 고려하여 운동심상 훈련 군과 대조군으로 무작위로 할당되었다. 측정 방법으로는 트레드밀에서 심장부하 검사를 실시하였고, 최대산소섭취량, 운동 시간 및 회복 심박수를 측정하였다. 운동심상 훈련군은 일주일에 5번 운동심상 훈련을 적용하였다. 본 연구에서는 군 내 결과를 확인 하기 위하여 대응 t 검증을 하였고, 군간 비교를 위하여 독립 t검증을 실시하였다. 결과: 최대 산소 섭취량은 각 군의 전후 비교와 각 군 간의 비교에서 유의한 차이를 보였다. 운동심상 훈련군은 대조군에 비해 운동시간에 유의한 변화가 있었다. 회복 심박수에는 유의한 차이가 없었다. 결론: 본 연구에서는 운동심상 훈련군에서 최대산소섭취량 및 운동 시간을 개선하지만 회복 심박수에는 영향을 미치지 않는 것으로 나타났다. 따라서 운동심상 훈련은 심폐 기능 강화를 위한 프로그램으로 고려할 가치가 있다

보물 제1746호로 지정된 논산 노강서원강당은 2008년 정밀안전진단, 2015~2017년 주기적인 모니터링 결과에 따라 2017년 보수정비기본계획을 수립을 통해 현재 기둥이상 해체수리를 진행하고 있다. 강당의 건립시기는 기문헌(『노강서원지』, 각종 보고서, 문화재 안내 등)에서 1675년으로 보고 있으나, 해체 수리 과정에 서 확인된 중도리와 대공의 묵서, 기와 명문, 주요부재의 연륜연대 조사 등의 결과를 종합하여 창건시기를 검토해본 결과 1695년으로 확인되었다. 조선후기 서원의 기능이 교육에서 향사 중심으로 이동한 사실에 비춰본다면, 기존에 알려진 1675년 노강서원은 사당 중 심의 영역으로 건립된 후 1682년 사액을 통한 재정적 뒷받침을 바탕으로 1695년 강당을 신축한 것으로 보는 것이 타당하다 고 판단된다.

This study was carried out to investigate the proper wattage and installation distance for the efficient use of nano-carbon fiber infrared heating lamp (NCFIHL), a heating device advantageous for heating energy saving, when the production of watermelon plug seedlings in the plug seedling nursery in winter season. Six small beds were divided into plastic film, and 700 W and 900 W nano-carbon fiber infrared heating lamps were installed at 100 cm above the bed. 1 lamp at central (control), 60 cm interval (2 lamps), and 40 cm interval (3 lamps) heating lamps were installed in each bed inside the greenhouse. All treatments, except the control, were set to keep the night air temperature at 20℃ after lighting the NCFIHL. The leaf temperature showed a tendency to increase fast as the install distance was narrow. The leaf length and leaf width tended to increase as the installation distance of the 700 W heating lamp was narrow. The compactness was high in 700 W heating lamp with 40 cm of installation distance. Therefore, in consideration of maintaining the set temperature at night, installing 700 W electric lamps at 40 cm was an efficient power and installation distance for watermelon grafted seedlings considering economic feasibility.