PURPOSES : This study is conducted to evaluate the development of materials for extinguishing ESS(Energy Storage System) fires in electric vehicles using industrial byproducts. METHODS : Grout containing an appropriate amount of fly ash, silica fume, blast furnace slag powder, and ferronikel slag, which are industrial byproducts, was prepared. The fluidity, stress, and mechanical properties were evaluated in accordance with standard test methods. RESULTS : The fluidity of the materials used for the evolution of ESS fires differed depending on the material of the industrial byproducts. In the case of blast furnace slag, its fluidity is low owing to viscosity even when it content is high, and the use of ferronikelsrag is shown to be suitable for the evolution of ESS fires in fluidity and curing tests. CONCLUSIONS : Fire-extinguishing materials using industrial byproducts require a long curing time but exhibit the fluidity required for ESS fire extinguishment. In particular, the curing and fluidity of Peronikel slag and fly ash are suitable for ESS fire extinguishing.

In this paper, as there are many cases of fires occurring due to the failure or inoperability of the thermostat of electronic products, the purpose is to test and analyze the risks and probabilities through fire cases and reproduction experiments, and suggest countermeasures. Among electronic products, water purifiers are composed of a refrigerant system with a compressor to make cold water, a heating device to make hot water, and an electric device used as an energy source. Due to the nature of the water purifier manufacturing, these devices are subject to a lot of moisture and dust. etc. exist in large quantities and use electrical energy, so there is a possibility of fire due to short circuit in the wire, electrical abnormal overheating (tracking phenomenon) in the thermostat, electronic board, starting relay, etc., and overheating of the heating device (Band Heater). there is. Therefore, in order to prevent fires from these devices, a system to remove foreign substances inside the water purifier is necessary, the use of heat-resistant (fire-resistant) wires for electrical devices is essential, and the use of non-combustible materials (semi-combustible materials) for each part is necessary to prevent fire. The risk must be eliminated through prevention and combustion expansion prevention devices.

In recent years the tunnel construction is increasing worldwide because of development of science and technology and increasing of transportation demand. Tunnels are complex structures normally rectangular cross section or semicircular and constructed to connect between different sections of roads. Because of the importance, the construction and extension of road tunnels are also continuously increasing along with the development. According to data from the Korea Expressway Corporation, the number of road tunnels, which was 1,332 in 2010, increased rapidly by about 2.1 times over 10 years to a total of 2,742 in 2020. The extension of road tunnels is also on the trend of increasing, with a total of 945 km in 2010 reaching 2,157 km in 2020. The benefits of a double-deck tunnel are emphasized, particularly in terms of construction cost and convenience. This tunnel design incorporates a central slab, dividing the tunnel into upper and lower spaces. The versatility of a double-decker tunnel is evident in its ability to accommodate various uses for both levels. For instance, the upper level can function as vehicle roads, while the lower level can be designated for train tracks. In this study, the effect of RWS and modified hydrocarbon fire curve was applied to the concrete tunnel bracket through simulation to analyze the temperature after the fire occurrence.

In this study, in order to establish a strategy for developing an fire following earthquake risk assessment method that can utilize domestic public databases(building datas, etc.), the method of calculating the ignition and fire-spread among the fire following earthquake risk assessment methodologies proposed by past researchers is investigated After investigating and analyzing the methodology used in the HAZUS-MH earthquake model in the United States and the fire following earthquake risk assessment methodology in Japan, based on this, a database such as a domestic building data utilized to an fire following earthquake risk assessment method suitable for domestic circumstances (planned) was suggested.

This study attempted to analyze the comparative advantage in terms of disaster safety costs in verifying the effectiveness and economic feasibility of the high-performance water-bulwark system in the pole tunnel, which was recently promoted as a part of the acceleration of vehicles. The tunnel to be analyzed was divided into a short tunnel(Anyang, Cheonggye) and a long tunnel(Suraksan, Sapaesan). As a result, it was analyzed that 25% of the improvement effect would occur if one lane was secured by applying the Water-Bulwark System. It was analyzed that this is because the time value cost, which accounts for a large proportion of the traffic congestion cost of short tunnels and pole tunnels, differs depending on the congestion time and traffic volume, not the length of the tunnel.

콘크리트 구조물은 시간이 경과함에 따라 Steel Re-bar 부식 등이 원인이 되어 주요 구조부재의 내력이 저하된다. 이 를 방지하기 위해 아연도금, 에폭시 코팅, 피복두께 증가 등의 방법이 사용되지만 근본적인 문제가 해결되지 않는다. 최근 들어 Steel Re-bar를 대체할 복합섬유에 대한 연구가 활발히 수행된다. CFRP Re-bar는 경량이며 고강도이고 내식성이 우수하다. Steel Re-bar의 임계온도는 538℃인 반면 CFRP Re-bar의 임계온도는 250℃로 화재에 취약하다. 따라서 건설현장에 적용하기 위한 내 화피복 방안이 필요하다. 본 연구에서는 콘크리트 피복두께(40, 60, 80mm), SFRM(0, 15, 30mm)두께를 변수로 CFRP Re-bar가 배 근된 표준화재 3시간 노출된 콘크리트 기둥 단면의 온도분포를 확인하고, 온도상승에 따른 소재 강도 감소를 고려하여 P-M상관 도를 도출하였다. 이를 통해 건설현장에 CFRP Re-bar를 사용하기 위한 내화피복 두께를 제안하고자 한다. 1시간 내화성능을 만 족하기 위해 콘크리트 피복두께가 60mm 필요하며, 2시간은 80mm가 필요하다. SFRM 15mm를 도포하면 400×400 단면의 경우 2 시간, 600×600과 800×800 단면의 경우 3시간 내화성능을 만족한다.