This study evaluated the effectiveness of odor reduction when spraying inside the Bio-curtain (hereinafter referred to as curtain) according to the exhaust fan operating rate. Spraying is a main factor affecting the ability to odor reduction of curtains. The curtain (total area: 37.9m3) was constructed with two layers of light-shielding screens stretched over a rectangular parallelepiped structure installed around an exhaust fan (630 mm) on the side wall of a pig barn. Air samples for odor analysis were collected from inside the pig barn and outside the curtain. The main odorous compounds such as volatile fatty acids, phenols, indoles, and ammonia were measured. The odor reduction effectiveness was evaluated by total odor activity values (TOAVs) summed to the odor activity values of each odorous compounds. Depending on the exhaust fan operating rate, the reduced rate of TOAVs gradually decreased to the range between 15.67% and 68.80%. Because the contact time between the spraying liquid and the air velocity of the exhaust fan becomes shorter (or there is a reduction in liquid to gas flow ratio) as the exhaust fan operating rate increases. The results of this study can be used as basic data for research into spraying conditions to improve the odor reduction effectiveness of curtains.

The operating parameters considered in this study include evaporating and condensing temperature, degree of subcooling and degree of superheating. in R744-R717 cascade refrigeration system and R744 two-stage compression refrigeration system with the range of low temperature -50℃∼-30℃. The coefficient of performance(COP) of R744-R717 cascade refrigeration system is about 16∼20% greater than that of R744 two-stage compression refrigeration system in the range of evaporation temperature of -50℃∼-30℃. R744 two-stage compression refrigeration system is unstable because its coefficient of performance changes significantly depending on the evaporating temperature and total compression work, and compression efficiency decreases. In this case, not efficient for long-term use. Whereas R744-R717 R744-R717 is a cascade refrigeration system using eco-friendly refrigerants. And this system is a high-efficiency refrigeration system that performs well even under various operating conditions. This is why it can be configured by selecting a refrigerant suitable for the high temperature side and the low temperature side.

PURPOSES : This study aims to propose drone-command standard operating procedure (SOP) guidelines and Analyze their potential application to increase the use and utility of drones in urban disaster situations. Although the effectiveness and efficiency of obtaining disaster-situation information through drones have been verified by previous studies and practical experience, a survey of actual drone usability indicated a utilization rate of only approximately 4.13%. METHODS : To provide guidance for improving drone command SOPs, prior research and relevant literature were reviewed to identify commonalities between disaster-response command and control and drone use. A sample of 73 active-duty firefighters, including incident commanders (ICs) and drone pilots, were surveyed and interviewed. The data were analyzed and categorized to establish the reasons why drones are not actively used in urban disaster-response procedures. RESULTS : The primary reasons identified for not actively utilizing drones in urban disaster areas were the lack of a drone command and control system and the lack of clear criteria for when to use drones in disaster situations. In addition, many problems were found in drone-operation procedures, including emergency flight approval, securing takeoff and landing sites, and accident burden due to urban flight obstacles. To address the issues identified, standards were proposed for the type, size, and scope of urban disasters requiring drone response; for accident-prevention on basic missions and through flight safety procedures; and for installing a video transmission and reception system to easily share drone video information with ICs. CONCLUSIONS : Application of the drone-command SOP guidelines to actual urban disaster situations by disaster type will help to improve the efficiency of information acquisition and flight safety. This is expected to enable increased drone utilization. In future, extension of the research reported in this paper beyond the Seoul metropolitan area via additional follow-up studies has the potential to establish applicability of the proposed SOP guidelines to a wide variety of environments and organizational characteristics.

Wastewater management is increasingly emphasizing economic and environmental sustainability. Traditional methods in sewage treatment plants have significant implications for the environment and the economy due to power and chemical consumption, and sludge generation. To address these challenges, a study was conducted to develop the Intermittent Cycle Extended Aeration System (ICEAS). This approach was implemented as the primary technique in a full-scale wastewater treatment facility, utilizing key operational factors within the standard Sequencing Batch Reactor (SBR) process. The optimal operational approach, identified in this study, was put into practice at the research facility from January 2020 to December 2022. By implementing management strategies within the biological reactor, it was shown that maintaining and reducing chemical quantities, sludge generation, power consumption, and related costs could yield economic benefits. Moreover, adapting operations to influent characteristics and seasonal conditions allowed for efficient blower operation, reducing unnecessary electricity consumption and ensuring proper dissolved oxygen levels. Despite annual increases in influent flow rate and concentration, this study demonstrated the ability to maintain and reduce sludge production, electricity consumption, and chemical usage. Additionally, systematic responses to emergencies and abnormal situations significantly contributed to economic, technical, and environmental benefits.

This study addresses the optimal design methodology for switching between active electronically scanned array (AESA) radar operating modes to easily select the necessary information to reduce pilots' cognitive load and physical workload in situations where diverse and complex information is continuously provided. This study presents a procedure for defining a hidden Markov chain model (HMM) for modeling operating mode changes based on time series data on the operating modes of the AESA radar used by pilots while performing mission scenarios with inherent uncertainty. Furthermore, based on a transition probability matrix (TPM) of the HMM, this study presents a mathematical programming model for proposing the optimal structural design of AESA radar operating modes considering the manipulation method of a hands on throttle-and-stick (HOTAS). Fighter pilots select and activate the menu key for an AESA radar operation mode by manipulating the HOTAS’s rotary and toggle controllers. Therefore, this study presents an optimization problem to propose the optimal structural design of the menu keys so that the pilot can easily change the menu keys to suit the operational environment. K

As aerial application increasing, with social concerning in pesticide drift rises, so this study attempts to establish a test bench that can repeatedly and continuously evaluate this. To this end, this study first analyze ISO 22866 and ASABE S561.1 among the international standard test methods related to pesticide fugitive evaluation. A test bench was established at the Naju practice field of Chonnam National University in accordance with international standards, and field tests were carried out (ISO 22866, ASABE S561.1) to verify effectiveness. A test bench that established in this study and a pesticide drift recovery protocol by aerial application can improve the experimental environment where field experiments were complex and it was difficult to achieve the same conditions. In addition, it will be possible to construct a database of pesticide drift that takes into account various factors that affect pesticide drift substances, which is expected to improve the reliability of the data, as well as quantitative evaluation of pesticide drift in the air.

This descriptive correlational study describes the relationship between collaboration among health care professions and nurses’ organizational commitment in the operating room. A cross sectional survey of nurses (N = 142) was conducted in March 2020. The participants were nurses with more than one year work experience in operating rooms at three university hospitals in Seoul and Gyeonggi-do. Collaboration among nurses was measured using the Nurse–Nurse Collaboration Scale, while collaboration between nurses and physicians was measured by the Nurse-Physician Collaboration Scale (NPCS). All analyses were conducted using the IBM SPSS Statistics, version 23.0 with independent t-test, one-way ANOVA, Scheffé test, Pearson's Correlation, and multiple regression. The results were as follows : The collaboration among operating room nurses was scored with an average of 2.87 out of a total of 4. Collaboration between operating room nurses to physician scored 3.47 average out of 5 total. Organizational commitment scored 3.24 average out of 5 total. The factors influencing the organizational commitment of nurses in operating rooms include collaboration among nurses and effective communication, as well as collaboration between nurses and physicians for decision-making regarding treatment and nursing care. The explanatory amount of general characteristic, nurse-physician collaboration, and nurse-nurse collaboration variables was 33%, 15%, 13% respectively. Based on these findings, to enhance collaboration among operating room nurses, there is a significant need for systematic education on communication skills and decision-making competencies, continuous research, and organizational efforts.

PURPOSES : This study proposes a method for comparative analysis, based on geographic information systems (GIS), that can be used when introducing demand-responsive transit in areas where public transportation is not available. METHODS : To analyze areas where public transportation is neglected, bus stop location information, building location information, and administrative district boundary data for the census were acquired. Geocoding was used for address-based raw data to create a spatial database. Based on the collected data, the proportion of households separated by a certain minimum distance from a bus stop was aggregated and constructed through near analysis. When introducing a demand-responsive transit system, the operational cost was calculated and compared with the existing city bus transportation cost. RESULTS : Results show that the operating costs of introducing demand-responsive transit can be compared and analyzed using the proposed method, for a case study of Daejeon Metropolitan City. CONCLUSIONS : It is economically efficient to avoid the entry of route buses and introduce demand-responsive transit in areas isolated from public transportation where the number of people getting on and off is extremely low.

The purpose of this study is to provide technical issues in upgrade and modification of fuel handling equipment at operating nuclear power plants. The improvement for safety function and performance enhancement of fuel handling equipment has been going on for 20 years since the early 2000’s. This improvement is recently focused on the replacement of components through the performance analysis and the operation and maintenance plan based on replacement cycle of its component. Additionally, it is required to secure spare parts so that it can be operated at all times with compatibility and standardization to other domestic nuclear power plants. The fuel handling equipment is consisted of refueling machine, upender and carriage of fuel transfer system, spent fuel handling machine, new fuel elevator and various tools, and the equipment are linked in systematic interlocks. Fuel handling is a critical task during a nuclear power plant refueling outage. Even minor component defects may stop operation of the whole system and have a significant impact on the overall system process. To achieve this goal, major components that are expected to be replaced for reliable operation are summarized as follows; 1) motor assembly with AC servomotors and driver for bridge, trolley and hoist of refueling machine and spent fuel handling machine, 2) winch motor and drive for upender and carriage of fuel transfer system, 3) operator control console with a HMI PC base PLC (Programmable Logic Controller) control system, 4) positioning and load weighing sensors such as an encoder and a load cell with its support for periodic calibration and maintenance, 5) main power drapped style festoon cable assembly for bridge of refueling machine, 6) pneumatic control assembly for gripper operation of refueling machine, 7) active components (e. g., air motor, hydraulic cylinder and limit switch) to be removable and reinstallable without requiring the water level to be lowered. It is advisable to utilize such various information as it can help to improve reliability of fuel handling as a critical path in upgrade and modification of fuel handling equipment at operating nuclear power plants.

단계별 작업기를 통합하여 일관화하는 복합기를 실용화하여 생산효율이 개선되어 밭농업 생력화에 기여하였다. 본 연구의 목적은 SAS를 이용한 복합작업기의 최적 작업조건을 반응표면기법(RSM)으로 구명하고 최적 성능을 실험으로 평가하여 집약적 밭농업의 트랙터 운용방법을 제시하고자 하였다. 로터리 작업에서 회전속도와 전진속도의 관계는 견인력의 효율성과 멀칭 등 작업품질에 적정한 트랙터의 운용기준 조건을 나타낸다. 슬립과 공차를 고려하면 통합 선택기준 작업속도는 3.4<SPDcr<4.7 km/h 범위로 확장되고, 로터리 피치(p)가 40<p<56 cm/rev로 판단되었다. 여러 검토조건에 서 연료소비량을 예측하고 동력의 효율성을 평가하는데 Kim 모델이 사용되었다. 목적함수를 만족하는 적정 p의 범위에 속하는 공칭 작업속도(SPD)를 엔진속도비(n)와 주행 기어비(GR)로 나타내어 최적 설계점은 카테고리 1급(DK450) 트랙터에 대하여 독립변수 n, GR/변속단수는 0.65, 401/M4로 구명되었다. 실험 평가에서 작은 트랙터는 시뮬레이션과 비교적 일치하였고, 큰 트랙터의 실험은 낮은 연료소비량과 실작업속도로 오차를 유발하였다.

This paper is the result of a comparative analysis of crew members' workloads using the EMG and OWAS methods according to the fishing process before and after the improvement of the operating system of the experimental vessel, with the aim of improving operational efficiency and safety work of coastal improved stow net fishing vessels. The target crew members were three people with at least five years of experience on board the same fishing vessel as the experimental vessel. After improving the operating system, such as installing a power block crane and two capstans, change the location of the ball-roller, the time required for setting and hauling work decreased (p < .01), and the evaluation results by OWAS showed that the overall workload for setting and hauling net work decreased. The results of muscle activity analysis showed a decrease in lashing anchor work (p < .01) in the case of hauling net and in anchor dropping work in the case of setting net (p < .001). It is judged that the use of ball rollers in net handling has been reduced; consequently, work safety has been improved.

Complaints about foul odors are emerging as an issue, and the number of complaints is steadily increasing every year. Biofiltration is known to remove harmful or odorous substances from the atmosphere by using microorganisms, and full-scale biofilters are being installed and operated in various environmental and industrial facilities. In this study, the current status and actual odor removal efficiency of full-scale biofilters installed in publicly owned treatment facilities such as sewage, manure, and livestock manure treatment plants were investigated. In addition, the effects of design and operating factors on their efficiency were also examined. As a result, it was found that odor prevention facilities with less than 30% odor removal efficiency based on complex odors accounted for 40%-50% of the biofilters investigated. In investigating the appropriate level of operating factors on odor removal efficiency, it was found that compliance with the recommended values p lays a significant role in improving odor removal efficiency. In the canonical correlation analysis for the on-site biofilter operation and design data, residence time and humidity were found to be the most critical factors. The on-site biofilter operation and design data were analyzed through canonical correlation analysis, and the residence time and humidity maintenance were found to be the most important factors in the design and operations of the biofilter. Based on these results, it is necessary to improve the odor removal efficiency of on-site biofilters by reviewing the effectiveness of the operation factors, improving devices, and adjusting operating methods.

밭농업의 일관화를 위해 개발된 복합작업기의 효율적인 운영전략은 연료절감의 목표와 함께 저속 로터리작업의 품질에도 중점을 두어야 한다. 본 연구는 둥근 두둑 복합작업기의 작업품질을 유지하는 적정조건에서 동력과 연료소비를 계상하고 비교하여 집약적 밭농업에서의 효율적인 작업기 운용전략을 제안하려 하였다. PTO 표준 시험성적을 이용한 Kim 모델은 임의의 부분 부하 상태에서 연료소비량(FC), 비체적 연료소비율(SVFC) 및 단위면적당 연료소비율(FCA)를 구하고 셀선도(shell diagram)를 얻을 수 있다. 따라서 개발된 복합작업기에 적용할 카테고리 1 트랙터(DK450)와 카테고리 2 트랙터(PX800)를 선정하고 적정운용 조건에서의 연료소비 특성을 비교하였다. 이전 연구를 바탕으로 이론적인 목표 작업속도는 3.0<SPDth<4.0km/h와 로터리 피치(p)가 35<p<47cm/rev인 범위를 적정한 작업 기준(criteria)으로 하여 운용조건을 선택하였다. 각 트랙터에서 적정한 운용조건의 사례들을 비교하면 작은 트랙터(DK 450)를 사용함으로써 얻을 수 있는 연료소비 절약율은 FC가 19.4%, SVFC가 21.1% 그리고 FCA가 29.9% 정도로 평가된다.

In the present study, the experimental study was conducted using a multi-calorie meter, to investigate the cooling performance and cycle operation changes of the multi-heat pump (3 indoor units) for the low outside temperature in summer. The test temperature condition was the low cooling temperature, and the normal performance and dynamic behavior of 3 rooms, 2 rooms, and 1 room were measured to understand the operating characteristics of seven 7 indoor unit combinations. As a result of the experiment, the cooling capacity and COP of the multi-heat pump at low cooling temperature were about 10% and 6% higher than those of the cooling standard temperature. In addition, the dynamic behavior of the indoor units of 3 and 2 rooms was observed differently due to the load difference according to the indoor unit combinations and the non-uniformity of the refrigerant amount. And, when starting the heat pump, the compressor had a maximum peak value and stabilized by repeating the decrease and increase for each indoor unit combination.

The purpose of this study is to provide lessons learned in the experience of improvement work of fuel handling equipment at operating nuclear power plants. The upgrade of fuel handling equipment for safety enhancement and performance improvement has been going on for 15 years since the early 2000’s. The main goal is to increase fuel loading/unloading capability of the equipment from about 2.5 fuel assemblies per hour to more than six (6). It is achieved with sequential operations of three (3) fuel handling equipment, which consists of the refueling machine, the fuel transfer system and the spent fuel handling machine. The scope of the upgrade for fuel handling equipment is summarized as follows. The PC data control system based on PLC for interlocks and high speed motor drive system is introduced for better operating efficiency. The motors and drives for bridge, trolley, and hoist are replaced with AC servomotors and drivers, respectively. The fuel transfer system has an auto-initiation feature operating from the refueling machine or the spent fuel handling machine. The winch motor and drive for the carriage of fuel transfer system is also replaced with AC servomotors and drivers. And some of HPU (hydraulic power units) equipment for each building (reactor containment building and fuel handling building) are replaced to improve their function. The considerations for improvement of fuel handling equipment are as belows. 1) Fuel handling should be consistent with the instructions provided by the fuel designer and/or manufacturer, which are for Standard type fuel and Westinghouse type fuel, used in domestic nuclear power plants. Each fuel has unique design characteristics, which are PLC setpoints for overload and underload, slow speed zones for a bridge, trolley and hoist, allowable acceleration/deceleration value in handling, hoist elevation and manual speed in off-index operation at reactor. 2) The interlock system should be designed in accordance with design criteria specified by the utilities of nuclear power plant. 3) Performance should be improved according to the operating characteristics of the fuel handling equipment. High-speed and optimization of FTS upender and carriage are essential for operating performance so that its modification should be considered first. And the low speed and range in the operation mechanism of the hoist should be designed to comply with guidelines. 4) The accident analysis through self-diagnosis function and operation history in modification at domestic operating nuclear power plants would be good lessons learned. It is advisable to utilize such various information as it can help to improve reliability of nuclear fuel handling operation and power plant operation rate.

Diesel engine has the advantages of strong power, low fuel consumption and good durability, so it has been widely used in transportation, automobile, ship and other fields. However, the nitrogen oxides(NOx) and particulate matter(PM) emitted by diesel engines have become one of the main causes of air pollution. Especially during idling, the engine temperature is low, and there are more residual exhaust gases in the combustion chamber, resulting in the formation of more harmful emissions. In this study, performance of a single cylinder, four-stroke, direct injection (DI) diesel engine fueled with diesel–biodiesel mixtures has been experimentally investigated. The findings show that a remarkable improvement in PM–NOx trade-off can be achieved by burning diesel-bioethanol blend fuels.

In order to experimentally investigate the operation characteristics of the multi-heat pump with 3 indoor units, the dynamic characteristics of the cooling cycle is studied using the psychrometric multi-calorimeter. The compressor of the heat pump is the scroll inverter type, and since 3 indoor units operate cooling at the same time, it is operated at 100% full load. In particular, 3 types of indoor unit temperatures (20, 24, 26°C) are selected to understand the operation process of the multi-heat pump by the setting temperature. From this experiment, the compressor controls the EEV opening for each indoor unit while varying the frequency according to the initial start, transient, and steady operation. In addition, as the setting temperature increases in the steady range, the frequency of the compressor and the average opening degree of the EEV decrease.