This study was conducted to determine the optimal spring seeding dates for alfalfa yield and feed value. The experiment was conducted annually for three years (2021~2023) at the field in the Department of Animal Resources Development, NIAS, located in Cheonan. The treatments involved six seeding dates ranging from February 24 to April 14, with 10days intervals. Alfalfa was harvested four times a year at the early flowering stage. Dry matter yield showed a tendency to decrease with delayed the seeding date. However, depending on the climatidc condisions in the seeding year, the dry matter yield on March 14 or 24 was comparable to that on February 24. Annual dry matter yield varied, influenced by the daylight conditions each year. The average feed value did not significantly differ within in the same year with delayed seeding dates (p>0.05). Therefore, the most stable period for alfalfa spring seeding in the central area of South Korea is considered to be from February 24 to April 4, with February 24 indentified as the optimal date.

This paper proposes the armored combat bulldozer, essential for amphibious tasks, requires water ingress prevention and submersion capabilities, typically addressed by a centrifugal pump. This study aims to boost the bulldozer's drainage pump efficiency by replacing the traditional aluminum 3-blade impeller with one made of ASA material using 3D printing. Analysis via ANSYS Fluent revealed that the 5-blade impeller increased discharge volume by 19.31% and efficiency by 6.07%, while the 6-blade variant saw a 27.07% increase in discharge volume and 8.81% efficiency improvement. Further scrutiny with ANSYS Static Structure ensured the new impellers' structural integrity and robustness under extreme conditions. This research confirms the potential of 3D printing in enhancing military equipment, demonstrating significant improvements in pump performance and opening paths for advanced manufacturing techniques to meet the demanding needs of combat vehicles.

This study investigated the physicochemical properties of protein-fortified rice flour by mixing rice flour (RF) with untreated and fermented plant proteins. Fermented faba bean protein concentrate (FMFP) and chickpea flour (FMCF) were prepared by solid-state fermentation of faba bean protein concentrate (UTFP) and chickpea flour (UTCF) using Bacillus subtilis. FMFP and FMCF exhibited higher crude protein, reducing sugar and starch contents more than their counterparts. The increased rate of essential and branched-chain amino acids in FMFP and FMCF exceeded that of crude protein. Adding plant proteins to RF decreased swelling power (SP) and increased solubility in RF-UTFP and RF-FMFP mixtures, while SP and solubility increased in RF-UTCF and RF-FMCF mixtures. All RF-plant protein mixtures showed higher gelatinization temperature and lower gelatinization enthalpy than RF. Thermal gelation was found in all RF-plant protein mixtures, but the RF-FMCF mixture may form weak and unstable gel structures. The increase in pasting viscosity was minimal for the RF-UTFP and RF-FMFP mixtures but more pronounced for the RF-UTCF and RF-FMCF mixtures. Overall, FMFP may be a potential protein source to supplement the protein deficiency in RF with minimal changes in RF-based foods’ rheological and textural properties.

Black chestnut (BC) was obtained through aging of fresh chestnut (FC) at 80℃ for 15 days. Proximate and mineral compositions along with colors of FC and BC were evaluated. With aging, moisture contents decreased by 50%, whereas sugar contents, carbohydrate contents, and calories increased. Contents of minerals (Fe, P, Ca, Na, Mg, K) were significantly higher in FC than in BC, showing an order of Mg < Ca < P < K in both FC and BC. Using a Hunter color system, it was found that lightness (L), redness (a), and yellowness (b) values of FC were higher than those of BC. Antioxidant and cytotoxic activities of hot water and ethanol (50, 80, 100%) extracts prepared from FC and BC were evaluated. Extraction yields were lower with FC than with BC. Among water and ethanol extracts, water extract showed the highest DPPH radical scavenging activity for both FC and BC. IC50 values for ABTS+ radical scavenging activities increased after aging. Cytotoxicities of FC and BC extracts were similar to each other. They were different against various cell lines (3T3, HeLa, and Sarcoma-180). These results suggest that BC could be used as a new processed food using chestnut.

Aluminum alloys, known for their high strength-to-weight ratios and impressive electrical and thermal conductivities, are extensively used in numerous engineering sectors, such as aerospace, automotive, and construction. Recently, significant efforts have been made to develop novel aluminum alloys specifically tailored for additive manufacturing. These new alloys aim to provide an optimal balance between mechanical properties and thermal/ electrical conductivities. In this study, nine combinatorial samples with various alloy compositions were fabricated using direct energy deposition (DED) additive manufacturing by adjusting the feeding speeds of Al6061 alloy and Al-12Si alloy powders. The effects of the alloying elements on the microstructure, electrical conductivity, and hardness were investigated. Generally, as the Si and Cu contents decreased, electrical conductivity increased and hardness decreased, exhibiting trade-off characteristics. However, electrical conductivity and hardness showed an optimal combination when the Si content was adjusted to below 4.5 wt%, which can sufficiently suppress the grain boundary segregation of the α- Si precipitates, and the Cu content was controlled to induce the formation of Al2Cu precipitates.

도심과 교외에 식재 또는 자생하고 있는 수목의 해충 발생 양상을 파악하기 위하여 2022년 5월부터 9월까지 전남 및 전북 내 총 6개소(전북 익산 2개소, 김제 1개소, 광주 3개소)에서 조사를 실시하였다. 조사지 6개소는 조사지역(공원)이 위치한 지역 특성에 따라 산림인접지역, 수변지 역, 도심지역 세 개의 지역으로 구분하여 각 특성 지역에 따라 확인되는 해충의 다양성을 비교, 분석하였다. 조사 결과 6개소의 조사지역에서 총 5 목 27과 49속 51종의 해충 분류군이 총 13과 21종의 주요 가로수종으로부터 확인되었다. 해충 분류군 중에서 노린재목이 12과 20속 22종으로 가장 많은 종이 포함되어 있었으며, 가로수 수종에서는 왕벚나무가 25종의 가장 다양한 해충의 피해를 입는 것을 확인하였다. 조사지역 특성별 비 교를 하였을 때, 수변지역 공원에 식재 또는 자생하는 수종은 상대적으로 적었지만 산림인접지역과 도심지역 공원에 비해서 가장 많은 해충 종 수 를 확인하였다. 해충이 가해하는 부위로는 잎을 가해하는 해충이 총 22종으로 가장 많았다. 본 조사를 통해 확보한 각 가로수 수종에 발생하는 해 충의 분류군 목록을 작성하였으며, 이 중에서 피해가 심한 6종을 선정하였다. 도심 뿐만 아니라 교외지역에서의 다양한 가로수 분포 범위가 확대 됨에 따라 발생할 수 있는 수목 해충이 증가될 수 있으므로 지속적인 해충 발생 양상 조사와 연구가 필요할 것으로 판단한다.

PURPOSES : Demonstrated performance degradation of LiDAR for vehicle and pedestrian dummy in rainy and foggy road conditions. METHODS : In real-scale rain and fog road conditions, adjust the distance between LiDAR and the measurement target from 10m to 70m (in 10m interval), measure LiDAR NPC (number of point cloud) and intensity, and compare the resulting numerical values. RESULTS : LiDAR's NPC and Intensity showed statistically significant differences by overall weather condition (normal, rain, fog), and the values were found to be larger in the order of normal>rainfall>fog. In the case of vehicles, sunder rain conditions, NPC and intensity are recognized even at 70m as in normal conditions, but under fog conditions, NPC and intensity are measured only up to 30m. In the case of pedestrians, the reflective area size is smaller than that of vehicles, so they are recognized only up to 30m in rainy conditions, and NPC and intensity are measured only up to 20m in fog conditions. CONCLUSIONS : It was confirmed that LiDAR performance deteriorates in rain and fog compared to normal.

2015년부터 2022년도까지 6개목(딱정벌레목, 노린재목, 나비목, 벌목, 파리목, 총채벌레목) 곤충들에 대해서 식물검역현장 검출실적과 국내 보고된 미기록종을 분석하였다. 해당기간 동안 국경검역에서 6개목 곤충은 총 45,084건이 검출되었다. 같은 기간 국내에서는 총 545종이 미기록종 으로 보고되었으며, 이중 9종은 국경검역에서도 검출된 것으로 확인되었다. 검역현장에서는 딱정벌레목, 총채벌레목, 노린재목이 높은 검출률을 보 였으며, 국내 미기록종 중에서는 벌목이 176종으로 가장 많이 보고되었다. 본 연구를 통해 침입압력(국경검역 검출)과 실제 침입(국내 미기록종 발 견) 사이에 비동시성이 확인되었다. 향후 보다 장기적인 분석이 필요할 뿐만 아니라 지속적인 식물검역시스템 개선이 필요할 것으로 판단된다.

PURPOSES : In this study, the basis for improving the maintenance method of road pavement in Jeju Island, where deterioration is accelerating, was presented through field construction and analysis of various combinations of maintenance methods. METHODS : Construction was performed on Jeju Island's Aejo Road, which has high traffic and frequent early damage, using various asphalt mixtures mainly applied in Jeju Island, with different maintenance cross-sections depending on the level of repair. The quality and performance of the asphalt mixture collected during construction were evaluated, and MEPDG was used to analyze the service life according to the type and maintenance level of the mixture. RESULTS : While the mixture for the surface layer satisfied the quality standards and had excellent rutting and moisture resistance performance, the asphalt mixture for the intermediate and base layer did not satisfy the quality standards such as air voids, so it was judged that quality control was necessary during production. The section repaired to the base layer was found to be advantageous for the integrated behavior of the pavement and had the best structural integrity. As a result of predicting the service life, the estimated life of the section where only the surface layer was repaired was analyzed to be approximately 7 years, the section where the intermediate layer was repaired was 14.5 years, and the section where the entire section up to the base layer was repaired was analyzed to be 18 years. CONCLUSIONS : In Jeju Island, where deterioration is accelerating, it was analyzed that when establishing a maintenance plan, it is necessary to consider repairing the middle and base floors in order to secure the designed life of 10 years.

PURPOSES : LED based Variable Message Signs(VMS) have been widely used to inform safety messages to the drivers in advance. Legibility Distance of VMS is the most important factor to provide the safety messages to drivers in timely and effective way. However, current National Standards on legibility distance design considers letter size only even there is a difficulty to read the signs at adverse weather conditions such as heavy fog. So, this study examined the legibility issue under fog by evaluating the legibility distance with two design factors such as letter size and luminance. METHODS : Two foggy weather conditions, intermediate and heavy fog, were simulated at real-road-scale Proving Ground. Legibility distance at daytime and nighttime was evaluated by test subjects. Subjects were asked to fill the legible distance on the test sheet and statistical significant was analysed at the lab. RESULTS : The legibility distance(LD) under fog was observed only 22 to 41% of LD observed under normal weather condition at daytime, and 26 to 45% at nighttime condition. Study results showed a consistent increase in LD with higher luminance even at same letter size and vice versa conditions, However, statically significant difference between groups was only revealed when both letter size and luminance level increased conditions. In order to apply the test results in terms of engineering benefits, LD results from significantly different groups was evaluated with relative to Stopping Sight Distance(SSD) within conceptual frame suggested in this study. CONCLUSIONS : From the study results, current National Standard on legibility distance design needs to consider letter size and luminance simultaneously to response the legibility issue in adverse weather conditions.

This study investigated the changes in the cyanogenic glycoside (CN-Glc) content of maesil chung (MC) prepared according to its preparation conditions (i.e., maesil part, sugar type, maesil-sugar mixing ratio, liquid separation) and sugaring-ripening period and the quality characteristics of their products finalized through filtration and heat treatment (85oC, 30 min) with the 6-month ripened MC. The CN-Glc content dramatically decreased when the maesil flesh, isomaltooligosaccharide, maesil:sugar ratio of 5:5, and liquid separation after the 4-month sugaring were applied to the MC production. The CN-Glc content decreased with the ripening period. There was no effect of filtration and heat treatment on the CN-Glc reduction of the MC product. The sugar type predominantly affected the soluble solid and total carbohydrate content of the MC products, and their contents increased in the order of high-fructose corn syrup > sucrose > isomaltooligosaccharide. The MC product at a maesil:sugar ratio of 6:4 exhibited the higher organic acid content. There was no direct association between the total polyphenolic compound content and the preparation conditions of the MC product. Overall, the use of maesil flesh as a maesil ingredient and more than 6-month ripening after liquid separation may be a pivotal factor in producing the cyanogenic glycoside-reduced maesil chung.

The objective of this study was to investigate changes in the cyanogenic glycoside (CN-Glc) content of apricot and plum chungs over the sugaring-ripening period and to evaluate their quality characteristics. The whole and flesh parts of the apricot and plum were mixed with sugar to a mixing ratio of 1:1 (w/w) to prepare their chungs, after which the fruit-sugar mixtures were stored for 13 months. The CN-Glc content dramatically increased within 3-4 months, reached the maximum, and gradually decreased over storage by 13 months. The apricot and plum chungs with seeds exhibited much higher CN-Glc contents than those without seeds. All chungs stored for 10 months were filtrated and treated for 30 min at 85oC to measure their quality characteristics. Similar soluble solid contents (53.4- 53.6oBx) were found in all chungs. The apricot and plum chungs without seeds exhibited the higher concentrations of total carbohydrate, organic acid, and total polyphenolic compounds than those with seeds. In addition, the color of the apricot and plum chungs without seeds was darker and deeper yellow than those with seeds. Overall, the apricot and plum flesh may be better for producing the stone fruit chungs with minimal CN-Glc content and better nutrition.